Hi, I get sound fine on both line in and tuner, it's only when I have used the tuner then when I use line in, the audio from the tuner gets mixed with the line in audio, so I get a double audio stream.
I need to know how I could possibly disable the tuner audio stream while using line in , maybe with some register value etc. On Wed, 4 Jan 2006 12:47:28 +0100 (CET) Isabel Romero <[EMAIL PROTECTED]> wrote: >type 'ivtvctl -Y' and look if Mute = yes > >[EMAIL PROTECTED] escribió: > >I'm running SUSE 10 (x86_64) kernel 2.6.13-7 (default >kernel). > >Suse 10 comes with ivtv 0.3.7, but I decided to go with >0.4.1 as 0.3.7 didn't have any sound coming from the >tuner, only line in. > >So, I upgraded to 0.4.1 and everything seemed to be >working fine, both composite+line in and the tuner. > >Then I noticed that after I had tuned into any one >station, the sound from that station bled into the line >in >when I used the composite input. > >There seems to be no way to get rid of this. I tried >every >setting I could think of in ivtvctl, to force the audio >input, but the audio input says "Line in", so that >doesn't >help. > >If I reload the kernel modules, then everything is fine >until I tune into a station. > >Any ideas? > >I have 0.4.2 running at the moment. > >ACPI: PCI interrupt for device 0000:00:05.0 disabled >ivtv0: Removed WinTV PVR 150, card #0 >tveeprom: module not supported by Novell, setting U taint >flag. >cx25840: module not supported by Novell, setting U taint >flag. >tuner: module not supported by Novell, setting U taint >flag. >wm8775: module not supported by Novell, setting U taint >flag. >ivtv: module not supported by Novell, setting U taint >flag. >ivtv: ==================== START INIT IVTV >==================== >ivtv: version 0.4.2 (development revision 3098) loading >ivtv: Linux version: 2.6.13-15.7-smp SMP gcc-4.0 >ivtv: In case of problems please include the debug info >between >ivtv: the START INIT IVTV and END INIT IVTV lines, along >with >ivtv: any module options, when mailing the ivtv-users >mailinglist. >ivtv0: Autodetected WinTV PVR 150 card (cx23416 based) >ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 16 (level, >low) >-> IRQ 185 >tveeprom: ivtv version >tveeprom: Hauppauge: model = 26559, rev = C260, serial# = >7627545 >tveeprom: tuner = LG S001D MK3 (idx = 60, type = 38) >tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L') >PAL(D/K) >(eeprom = 0x74, v4l2 = 0x00400e17) >tveeprom: audio processor = CX25843 (type = 25) >tveeprom: decoder processor = CX25843 (type = 1e) >ivtv0: i2c attach to card #0 ok [client=tveeprom, >addr=50] >cx25840 debug 1-0044: detecting cx25840 client on address >0x88 >cx25840 1-0044: ivtv driver >cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver >#0) >zaphfc: empty HDLC frame or bad CRC received (framelen = >5, stat = 0xff, card = 0). >cx25840 1-0044: loaded v4l-cx25840.fw firmware (14264 >bytes) >cx25840 debug 1-0044: decoder set input (0) >cx25840 debug 1-0044: now setting Tuner input >cx25840 debug 1-0044: set audio input (0) >ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44] >tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c >driver #0 >ivtv0: i2c attach to card #0 ok [client=(tuner unset), >addr=61] >ivtv0: i2c attach to card #0 ok [client=wm8775[50], >addr=1b] >cx25840 debug 1-0044: decoder set input (0) >cx25840 debug 1-0044: now setting Tuner input >tda9887: module not supported by Novell, setting U taint >flag. >tda9887 1-0043: (ivtv) chip found @ 0x86 (ivtv i2c driver >#0) >ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43] >ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) >zaphfc: empty HDLC frame or bad CRC received (framelen = >4, stat = 0xff, card = 0). >ivtv0: Encoder revision: 0x02040011 >ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 >buffers (4096KB total) >ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 >buffers (2048KB total) >ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 >buffers >(2048KB total) >ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 >buffers (2048KB total) >ivtv0: Create encoder radio stream >tuner: type set to 38 (Philips PAL/SECAM multi (FM1216ME >MK3)) by ivtv i2c driver #0 >cx25840 debug 1-0044: decoder set input (0) >cx25840 debug 1-0044: now setting Tuner input >cx25840 debug 1-0044: set audio input (0) >tuner: switching to v4l2 >insmod fixup: PAL => PAL-BG >cx25840 debug 1-0044: disable output >tuner: tv freq set to 400.00 >tuner: tv 0x1b 0x6f 0x8e 0x02 >cx25840 debug 1-0044: enable output >ivtv0: Initialized WinTV PVR 150, card #0 >ivtv: ==================== END INIT IVTV >==================== >cx25840 debug 1-0044: disable output >cx25840 debug 1-0044: decoder set input (1) >cx25840 debug 1-0044: now setting Composite input >cx25840 debug 1-0044: set audio input (6) >cx25840 debug 1-0044: enable output > >_______________________________________________ >ivtv-users mailing list >[email protected] >http://ivtvdriver.org/mailman/listinfo/ivtv-users > > > > >--------------------------------- > >Correo Yahoo! >Comprueba qué es nuevo, aquí >http://correo.yahoo.es _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
