I updated my ivtv to 0.4.2 and plugged it into cable and sound appears
to be working correctly.
Thanks for all your help!
- Chris Thielen
Hans Verkuil wrote:
>Please update to 0.4.2, remove the ivtv options from modprobe (why do
>people keep setting options?) tune to a known good channel and run
>ivtvctl --log-status. Please report the output.
>
>Thanks,
>
> Hans
>
>On Tuesday 17 January 2006 01:30, [EMAIL PROTECTED] wrote:
>
>
>>I still do not have sound working on tuner0 or tuner1. I have
>>modified my modprobe.conf and firmware files, so here is an update. I
>>no longer receieve messages about buggy firmware.
>>
>>Again, my problem is a Hauppage WinTV PVR500 with dual tuners. They
>>both work fine for video but there is no audio on MythTV or when I
>>cat /dev/video0 to a mpg and use mplayer or xine to play it. All
>>volume controls I can find are turned up all the way.
>>
>>As an important note, the volume in ivtvctl says mute=1, and using
>>ivtvctl -y mute=0 does not set the mute to 0, despite it saying OK.
>>
>>Here are my updated modconf and dmesg ivtv outputs:
>>Linux video capture interface: v1.00
>>ivtv: ==================== START INIT IVTV ====================
>>ivtv: version 0.4.1 (tagged release) loading
>>ivtv: Linux version: 2.6.14-1.1656_FC4smp SMP 686 REGPARM 4KSTACKS
>>gcc-4.0 ivtv: In case of problems please include the debug info
>>between ivtv: the START INIT IVTV and END INIT IVTV lines, along
>>with ivtv: any module options, when mailing the ivtv-users
>>mailinglist. ivtv0: User specified WinTV PVR 150 card (detected
>>cx23416 based chip) ACPI: PCI Interrupt 0000:04:08.0[A] -> GSI 25
>>(level, low) -> IRQ 201 ivtv0: i2c attach to card #0 ok
>>[client=tveeprom, addr=50]
>>tveeprom 1-0050: Hauppauge model 23552, rev D492, serial# 8023885
>>tveeprom 1-0050: tuner model is Philips FQ1236A MK4 (idx 92, type 57)
>>tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
>>tveeprom 1-0050: second tuner model is Philips TEA5767HN FM Radio
>>(idx 101, type 62)
>>tveeprom 1-0050: audio processor is CX25843 (idx 37)
>>tveeprom 1-0050: decoder processor is CX25843 (idx 30)
>>tveeprom 1-0050: has radio, has no IR remote
>>ivtv0: This is the first unit of a PVR500
>>tuner 1-0060: chip found @ 0xc0 (ivtv i2c driver #0)
>>tuner 1-0060: TEA5767 detected.
>>ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=60]
>>tuner 1-0060: type set to 62 (Philips TEA5767HN FM Radio)
>>tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
>>ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
>>cx25840 1-0044: ivtv driver
>>cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
>>cx25840 1-0044: loaded v4l-cx25840.fw firmware (14264 bytes)
>>ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
>>wm8775 1-001b: ivtv driver
>>wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
>>ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
>>tda9885/6/7: chip found @ 0x86
>>ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
>>ivtv0: Detected a TEA5767 radio tuner. Enabling radio support.
>>ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
>>ivtv0: Encoder revision: 0x02050032
>>ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB
>>total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers
>>(2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472
>>buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream:
>>455 x 4608 buffers (2048KB total)
>>ivtv0: Create encoder radio stream
>>tuner 1-0061: type set to 57 (Philips FQ1236A MK4)
>>ivtv0: Initialized WinTV PVR 500 (unit #1), card #0
>>ivtv: ====================== NEXT CARD ======================
>>ivtv1: Autodetected WinTV PVR 150 card (cx23416 based)
>>ACPI: PCI Interrupt 0000:04:09.0[A] -> GSI 26 (level, low) -> IRQ 209
>>ivtv1: i2c attach to card #1 ok [client=tveeprom, addr=50]
>>tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #1)
>>ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=61]
>>cx25840 2-0044: ivtv driver
>>cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1)
>>cx25840 2-0044: loaded v4l-cx25840.fw firmware (14264 bytes)
>>ivtv1: i2c attach to card #1 ok [client=cx25840, addr=44]
>>wm8775 2-001b: ivtv driver
>>wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #1)
>>ivtv1: i2c attach to card #1 ok [client=wm8775, addr=1b]
>>tda9885/6/7: chip found @ 0x86
>>ivtv1: i2c attach to card #1 ok [client=tda9887, addr=43]
>>tveeprom 2-0050: Hauppauge model 23552, rev D492, serial# 8023885
>>tveeprom 2-0050: tuner model is Philips FQ1236A MK4 (idx 92, type 57)
>>tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08)
>>tveeprom 2-0050: second tuner model is Philips TEA5767HN FM Radio
>>(idx 101, type 62)
>>tveeprom 2-0050: audio processor is CX25843 (idx 37)
>>tveeprom 2-0050: decoder processor is CX25843 (idx 30)
>>tveeprom 2-0050: has radio, has no IR remote
>>ivtv1: This is the first unit of a PVR500
>>ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
>>ivtv1: Encoder revision: 0x02050032
>>ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB
>>total) ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers
>>(2048KB total) ivtv1: Allocate DMA encoder VBI stream: 120 x 17472
>>buffers (2048KB total) ivtv1: Allocate DMA encoder PCM audio stream:
>>455 x 4608 buffers (2048KB total)
>>ivtv1: Create encoder radio stream
>>tuner 2-0061: type set to 57 (Philips FQ1236A MK4)
>>ivtv1: Initialized WinTV PVR 500 (unit #1), card #1
>>ivtv: ==================== END INIT IVTV ====================
>>
>>modprobbe.conf:
>>alias eth0 e1000
>>alias snd-card-0 snd-intel8x0
>>options snd-card-0 index=0
>>options snd-intel8x0 index=0
>>remove snd-intel8x0 { /usr/sbin/alsactl store 0 >/dev/null 2>&1 || :
>>; }; /sbin/modprobe -r --ignore-remove snd-intel8x0
>>alias usb-controller ehci-hcd
>>alias usb-controller1 uhci-hcd
>>alias ieee1394-controller ohci1394
>># nvidia kernel module
>>alias char-major-195 nvidia-1_0-7667
>>alias nvidia nvidia-1_0-7667
>># ivtv (pvr-500)
>>alias char-major-81 ivtv
>>alias char-major-81-0 ivtv
>>alias char-major-81-1 ivtv
>>options ivtv ivtv_std=1 tuner=57,57 cardtype=6
>>
>>Any help in getting sound working would be much appreciated! Sound
>>card is working btw, if I use play and tell it to play a .wav file or
>>something.
>>
>>Thanks!
>>- Chris Thielen
>>
>>
>>
>>>I found a page,
>>>http://ivtv.writeme.ch/tiki-index.php?page=FirmwareVersions, that
>>>seems to list a lot of firmware revisions for Hauppage cards, and I
>>>downloaded the one recommended for ivtv 0.3.9 or later (I'm running
>>>0.4.1) but the zip file only contains .inf and .sys files, yet my
>>>/lib/modules/ directory for ivtv has .rom and .bin files. How do I
>>>use these recommended firmware files to see if it is indeed the
>>>cause of my no sound on a PVR500?
>>>
>>>Thanks,
>>>Chris Thielen
>>>
>>>
>>>
>>>>>ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
>>>>>ivtv0: Encoder revision: 0x02040024
>>>>>ivtv0 warning: Encoder Firmware can be buggy, use version
>>>>>0x02040011 or 0x02050032.
>>>>>
>>>>>
>>>>>
>>>>>>> What should I try?
>>>>>>>
>>>>>>>
>>>>it might be nothing, but i would try to fix this first.
>>>>
>>>>Chris
>>>>
>>>>
>>>>_______________________________________________
>>>>ivtv-users mailing list
>>>>[email protected]
>>>>http://ivtvdriver.org/mailman/listinfo/ivtv-users
>>>>
>>>>
>>>_______________________________________________
>>>ivtv-users mailing list
>>>[email protected]
>>>http://ivtvdriver.org/mailman/listinfo/ivtv-users
>>>
>>>
>>_______________________________________________
>>ivtv-users mailing list
>>[email protected]
>>http://ivtvdriver.org/mailman/listinfo/ivtv-users
>>
>>
>
>_______________________________________________
>ivtv-users mailing list
>[email protected]
>http://ivtvdriver.org/mailman/listinfo/ivtv-users
>
>
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
