On 1/31/06, Pieter Van Gorp <[EMAIL PROTECTED]> wrote: > Adding the PS2 mouse didn't help. Turns out I'm in a totally > different situation since I even don't have an ivtv0 entry in > /proc/interrupts... > > I do have some messages about missing firmware in dmesg after system > boot. Strange since I precisely followed the Wiki page... Unlike > those from the "PVR 150 on SUSE 10" thread, all required files are in > the hotplug directory... still I get: > > ivtv: ==================== START INIT IVTV ==================== > ivtv: version 0.4.2 (tagged release) loading > ivtv: Linux version: 2.6.13.2-chw-3 SMP preempt 586 gcc-3.3 > ivtv: In case of problems please include the debug info between > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > ivtv: any module options, when mailing the ivtv-users mailinglist. > ivtv0: Autodetected WinTV PVR 150 card (cx23416 based) > ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 19 > ivtv0: Unreasonably low latency timer, setting to 64 (was 32) > tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 > ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] > tuner: type set to 47 (LG NTSC (TAPE series)) by insmod option > tuner: The type=<n> insmod option will go away soon. > tuner: Please use the tuner=<n> option provided by > tuner: tv aard core driver (bttv, saa7134, ...) instead. > tveeprom: ivtv version > tveeprom: Hauppauge: model = 26559, rev = C260, serial# = 2898696 > tveeprom: tuner = LG S001D MK3 (idx = 60, type = 38) > tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L') PAL(D/K) (eeprom = > 0x74, v4l2 = 0x00400e17) > tveeprom: audio processor = CX25843 (type = 25) > tveeprom: decoder processor = CX25843 (type = 1e) > ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] > cx25840: Unknown parameter `i2c_enable' > ivtv0: Failed to load module cx25840 > ivtv0 warning: i2c client addr: 0x44 not found for command 0xc008561c! > wm8775 1-001b: ivtv driver > wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0) > ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b] > tda9887 1-0043: (ivtv) chip found @ 0x86 (ivtv i2c driver #0) > ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43] > ivtv0: unable to open firmware v4l-cx2341x-enc.fw > ivtv0: did you put the firmware in the hotplug firmware directory? > ivtv0 warning: failed loading encoder firmware > ivtv0 warning: Error loading firmware -3! > ivtv0: Error -3 initializing firmware. > ivtv0: Error -12 on initialization > ivtv: probe of 0000:00:09.0 failed with error -12 > ivtv: ==================== END INIT IVTV ==================== > > > Frustratings since for some KnopMyth users the PVR 150 seems to work > out of the box... what info should I post to the list to get this > fixed? > > In another thread, someone pointed out that it's strange that the > tuner type is set to LG... Well, indeed that's strange but with IVTV > 0.3.x I had to set the tuner type to 47 to make it work... did > something change since then?
Well seen as it went from 0.3.x to 0.4.2 I think they might have changed more stuff than just the version-number. Get rid of ALL module options. This are mine: --- module options for ivtv alias char-major-81 videodev alias char-major-81-0 ivtv alias char-major-81-1 ivtv alias char-major-81-2 ivtv --- And I don't even know if these are needed; they just make sure the ivtv-module is loaded for the correct major number. Since you gave un unknown parameter to the cx25840 module (it got removed as no longer needed... that's a change :-) ), the module didn't load. Probably that's also the reason why the firmware doesn't load. So in short: *get rid of all module options, they usually are not needed and cause more problems than they solve!* Grtz, N. _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
