Is hotplug enabled in your kernel? The tveeprom error also suggests that
a tveeprom module from ivtv got installed somehow. For 2.6.15 it is
recommended to use the supporting i2c modules from the kernel instead
of from ivtv. You get them build by enabling the config items
CONFIG_VIDEO_AUDIO_DECODER and CONFIG_VIDEO_DECODER.
Hans
On Wednesday 15 March 2006 20:20, Ola Theander wrote:
> Dear subscribers
>
> I have recently purchased a Hauppuage PVR 150 PCI TV/framegrabber
> card to use for my project. Unfortunately I have some minor problems
> to make it work on my Linux computer. Below I have attached the
> section of my dmesg output that concerns the loading of the ivtv
> kernel modules. As far as I can see the module has a problem with
> finding the firmware files. I find that pretty strange since I have
> double checked the path and file names, especially with regard to the
> potential hard to see misspelling of the v4l where the last character
> might be mistaken for the digit one. The content of the
> /lib/usr/hotplug/firmware folder is also attached below so that the
> content of this directory can be verified.
>
> If I, even though the errors during boot, try the command "ivtvctl
> -a" the command responds "Failed to open /dev/video0: No such device"
> and the following two lines are added to dmesg output:
>
> "bttv: disagrees about version of symbol tveeprom_hauppauge_analog
> bttv: Unknown symbol tveeprom_hauppauge_analog"
>
> I'm running Gentoo 2006.0 with the 2.6.15 kernel and have downloaded
> the 0.4.3 version of the Ivtv driver. The firmware are extracted from
> the files recommended at http://ivtvdriver.org/index.php/Firmware,
> i.e. "pvr_1.18.21.22254_inf.zip" and "pvr_2.0.24.23035.zip".
>
> The computer hardware is a Lex MV823A (http://www.lex.com.tw)
> mini-ITX single board computer which is based on the VIA CLE266
> platform.
>
> Any help with this matter would be greatly appreciated.
>
> Kind regards, Ola Theander
>
> The content of /lib/usr/hotplug/firmware:
>
> localhost firmware # pwd
> /usr/lib/hotplug/firmware
> localhost firmware # ls -l
> total 808
> -rw-r--r-- 1 root root 262144 Mar 15 11:56 v4l-cx2341x-dec.fw
> -rw-r--r-- 1 root root 376836 Mar 15 11:54 v4l-cx2341x-enc.fw
> -rw-r--r-- 1 root root 155648 Mar 15 11:58 v4l-cx2341x-init.mpg
> -rw-r--r-- 1 root root 14264 Mar 15 11:54 v4l-cx25840.fw
> localhost firmware #
>
> The dmesg section concerning ivtv:
>
> Linux video capture interface: v1.00
> ivtv: ==================== START INIT IVTV ====================
> ivtv: version 0.4.3 (tagged release) loading
> ivtv: Linux version: 2.6.15-gentoo-r1 VIAC3-2 4KSTACKS gcc-3.4
> ivtv: In case of problems please include the debug info between
> ivtv: the START INIT IVTV and END INIT IVTV lines, along with
> ivtv: any module options, when mailing the ivtv-users mailinglist.
> ivtv0: Autodetected WinTV PVR 150 card (cx23416 based)
> ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKB] -> GSI 10 (level,
> low) -> IRQ 10
> ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
> tveeprom: ivtv version
> tveeprom: Hauppauge: model = 26559, rev = F089, serial# = 9315658
> tveeprom: tuner = TCL MFPE05 2 (idx = 89, type = 38)
> tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L') PAL(D/K) (eeprom =
> 0x74, v4l2 = 0x00400e17)
> tveeprom: audio processor = CX25843 (type = 25)
> tveeprom: decoder processor = CX25843 (type = 1e)
> ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
> tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
> ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
> cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
> cx25840 0-0044: unable to open firmware v4l-cx25840.fw
> ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
> wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
> ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
> tda9887 0-0043: (ivtv) chip found @ 0x86 (ivtv i2c driver #0)
> ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
> ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011066645755c37]
> eth1394: $Rev: 1312 $ Ben Collins <[EMAIL PROTECTED]>
> eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
> ivtv0: unable to open firmware v4l-cx2341x-enc.fw
> ivtv0: did you put the firmware in the hotplug firmware directory?
> ivtv0 warning: failed loading encoder firmware
> ivtv0 warning: Error loading firmware -3!
> ivtv0: Error -3 initializing firmware.
> ivtv0: Error -12 on initialization
> ivtv: probe of 0000:00:0d.0 failed with error -12
> ivtv: ==================== END INIT IVTV ====================
>
>
> _______________________________________________
> ivtv-users mailing list
> [email protected]
> http://ivtvdriver.org/mailman/listinfo/ivtv-users
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
