If this doesn't help then I'd like to see the output of i2cdetect -a X
where X is the i2c bus number for the ivtv card that you can find with
i2cdetect -l. i2cdetect is part of lm-sensors.
It may also be that the tuner has to be enabled. So after running
i2cdetect for the first time you should run ivtvctl --set-gpio
dir=0xffff,val=0xffff and run i2cdetect -a again.
Thanks,
Hans
On Thursday 16 March 2006 08:00, Hans Verkuil wrote:
> Please remove (rm) the tveeprom.ko file from /lib/modules/...
> Then run rmmod ivtv tveeprom and try again. The PG600 definitely has
> no support for tveeprom, so it could be that the tuner is on the same
> i2c address as the tveeprom usually is. Hence the tuner is
> misdetected as a tveeprom.
>
> Hans
>
> On Thursday 16 March 2006 02:06, Robert Bungener wrote:
> > Hans,
> >
> > Sorry to bother again.
> >
> > I did the whole trunk thing and the dvb stuff and got everything
> > compiled as should without errors !!
> > the dmesg gives:
> > ivtv: ==================== START INIT IVTV ====================
> > ivtv: version 0.4.3 (tagged release) loading
> > ivtv: Linux version: 2.6.15-1.1833_FC4 686 REGPARM 4KSTACKS
> > gcc-4.0 ivtv: In case of problems please include the debug info
> > between ivtv: the START INIT IVTV and END INIT IVTV lines, along
> > with ivtv: any module options, when mailing the ivtv-users
> > mailinglist. ivtv0: User specified YUAN PG600/DIAMOND PVR-550 (CX
> > FALCON2) card (detected cx23416 based chip)
> > ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKA] -> GSI 11
> > (level, low) -> IRQ 11
> > tveeprom: Encountered bad packet header [ff]. Corrupt or not a
> > Hauppauge eeprom.
> > ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
> > cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
> > cx25840 2-0044: loaded v4l-cx25840.fw firmware (14264 bytes)
> > ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
> > ivtv0: Could not detect tuner standard, defaulting to NTSC.
> > ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> > ivtv0: Encoder revision: 0x02050032
> > ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers
> > (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800
> > buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120
> > x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM
> > audio stream: 455 x 4608 buffers (2048KB total)
> > ivtv0 warning: i2c client addr: 0x00 not found for command
> > 0x40045403! cx25840 2-0044: 0x0000 is not a valid video input!
> > ivtv0 warning: i2c client addr: 0x00 not found for command
> > 0x40085618! ivtv0 warning: i2c client addr: 0x00 not found for
> > command 0x402c5639! ivtv0: Initialized YUAN PG600/DIAMOND PVR-550
> > (CX FALCON2), card #0 ivtv: ==================== END INIT IVTV
> > ====================
> >
> > This is with the mdoprobe.conf as :
> > # ivtv modules setup
> > alias char-major-81 dvb-ttpci
> > alias char-major-81-0 ivtv
> > options ivtv cardtype=7 tuner=71
> > options msp3400 once=0 simpler=1 simple=0
> >
> > To me it seems that the tuner is not working or the firmware has a
> > hickup ?? I tried also with the shipped Falcon2 firmware but that
> > just gives me more errors
> > dmesg with that gives:
> > ivtv: ==================== START INIT IVTV ====================
> > ivtv: version 0.4.3 (tagged release) loading
> > ivtv: Linux version: 2.6.15-1.1833_FC4 686 REGPARM 4KSTACKS
> > gcc-4.0 ivtv: In case of problems please include the debug info
> > between ivtv: the START INIT IVTV and END INIT IVTV lines, along
> > with ivtv: any module options, when mailing the ivtv-users
> > mailinglist. ivtv0: User specified YUAN PG600/DIAMOND PVR-550 (CX
> > FALCON2) card (detected cx23416 based chip)
> > ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKA] -> GSI 11
> > (level, low) -> IRQ 11
> > tveeprom: Encountered bad packet header [ff]. Corrupt or not a
> > Hauppauge eeprom.
> > ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
> > cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
> > cx25840 2-0044: loaded v4l-cx25840.fw firmware (14264 bytes)
> > ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
> > ivtv0: Could not detect tuner standard, defaulting to NTSC.
> > ivtv0: unable to open firmware v4l-cx2341x-enc.fw
> > ivtv0: did you put the firmware in the hotplug firmware directory?
> > ivtv0 warning: failed loading encoder firmware
> > ivtv0 warning: Error loading firmware -3!
> > ivtv0: Error -3 initializing firmware.
> > ivtv0: Error -12 on initialization
> > ivtv: probe of 0000:00:08.0 failed with error -12
> > ivtv: ==================== END INIT IVTV ====================
> >
> > My guess is that the tveeprom sw has an issue ??? Anyway to test
> > that ??
> >
> > If you want to take this off list that is OK with me as well ...
> >
> > Robert ([EMAIL PROTECTED] -- though in Mexico at the moment)
> >
> > On Wednesday 15 March 2006 13:24, Hans Verkuil wrote:
> > > This tuner is supported, but only in the v4l repository. It isn't
> > > even in the upcoming 2.6.16 kernel.
> > >
> > > That means that you are forced to use the 'trunk' of the ivtv
> > > subversion repository. See
> > > http://www.ivtvdriver.org/index.php/Svn_checkout on how to do it.
> > > Also read the README.1ST in the checked out ivtv directory.
> > >
> > > Then use ivtv module option tuner=71 to select the XCeive tuner.
> > > You also need the tuner's firmware. Put it with the other ivtv
> > > firmwares and use the filename xceive_xc_3028.fw. The firmware
> > > should be part of the Windows driver (something like cxxc.rom).
> > >
> > > I hope that will get it to work.
> > >
> > > Hans
> > >
> > > On Wednesday 15 March 2006 20:12, Robert Bungener wrote:
> > > > Ok Hans,
> > > >
> > > > I looked at the board last night and I found the following
> > > > chips
> > > >
> > > > CX23416-2
> > > > CX25843-23
> > > > XCEIVE AC2828 or RC2828 (can't read the letters they are too
> > > > damn small And some kind of mem chip ...
> > > >
> > > > Robert
> > > >
> > > > On Tuesday 14 March 2006 17:18, Hans Verkuil wrote:
> > > > > Hmm, I wonder if you have somewhat different hardware.
> > > > >
> > > > > Can you make a list of the chips on the card and also of the
> > > > > tuner name? For the latter you probably have to gently peel
> > > > > off the label in order to read the tuner type underneath.
> > > > >
> > > > > Hans
> > > > >
> > > > > On Wednesday 15 March 2006 00:10, Robert Bungener wrote:
> > > > > > OK got that fixed ...
> > > > > >
> > > > > > modprobe cardtype=7 radio=1
> > > > > > still missing some tuner info
> > > > > >
> > > > > > modprobe.conf has:
> > > > > > # ivtv modules setup
> > > > > > alias char-major-81 ivtv
> > > > > > alias char-major-81 videodev
> > > > > > alias char-major-81-0 ivtv
> > > > > > options ivtv tuner=2
> > > > > > options msp3400 once=0 simpler=1 simple=0
> > > > > >
> > > > > > dmesg gives:
> > > > > > ivtv: ==================== START INIT IVTV
> > > > > > ==================== ivtv: version 0.4.3 (tagged release)
> > > > > > loading
> > > > > > ivtv: Linux version: 2.6.15-1.1833_FC4 686 REGPARM
> > > > > > 4KSTACKS gcc-4.0 ivtv: In case of problems please include
> > > > > > the debug info between ivtv: the START INIT IVTV and END
> > > > > > INIT IVTV lines, along with ivtv: any module options, when
> > > > > > mailing the ivtv-users mailinglist. ivtv0: User specified
> > > > > > YUAN PG600/DIAMOND PVR-550 (CX FALCON2) card (detected
> > > > > > cx23416 based chip)
> > > > > > ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKA] -> GSI
> > > > > > 11 (level, low) -> IRQ 11
> > > > > > tveeprom: Encountered bad packet header [ff]. Corrupt or
> > > > > > not a Hauppauge eeprom.
> > > > > > ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
> > > > > > cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver
> > > > > > #0) cx25840 1-0044: loaded v4l-cx25840.fw firmware (14264
> > > > > > bytes) ivtv0: i2c attach to card #0 ok [client=cx25840,
> > > > > > addr=44] ivtv0: Could not detect tuner standard, defaulting
> > > > > > to NTSC. ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144
> > > > > > bytes) ivtv0: Encoder revision: 0x02050032
> > > > > > ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768
> > > > > > buffers (4096KB total) ivtv0: Allocate DMA encoder YUV
> > > > > > stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate
> > > > > > DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
> > > > > > ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608
> > > > > > buffers (2048KB total) ivtv0: Create encoder radio stream
> > > > > > ivtv0 warning: i2c client addr: 0x00 not found for command
> > > > > > 0x40045403! ivtv0 warning: i2c client addr: 0x00 not found
> > > > > > for command 0x40085618! ivtv0 warning: i2c client addr:
> > > > > > 0x00 not found for command 0x402c5639! ivtv0: Initialized
> > > > > > YUAN PG600/DIAMOND PVR-550 (CX FALCON2), card #0 ivtv:
> > > > > > ==================== END INIT IVTV ====================
> > > > > >
> > > > > > More info, I specified tuner=2 but that was only on the
> > > > > > "Howto" part. I could not find a list with the available
> > > > > > options ...
> > > > > >
> > > > > > Thanks,
> > > > > > Robert
> > > > > >
> > > > > > On Tuesday 14 March 2006 15:01, Hans Verkuil wrote:
> > > > > > > Run with ivtv module option cardtype=7. That should work.
> > > > > > > The card is misdetected as a PVR250, a different card
> > > > > > > altogether.
> > > > > > >
> > > > > > > Yuan makes a mess of their vendor IDs :-(
> > > > > > >
> > > > > > > Hans
> > > > > > >
> > > > > > > On Tuesday 14 March 2006 21:48, Robert Bungener wrote:
> > > > > > > > Hello list,
> > > > > > > >
> > > > > > > > I have a Yuan PG600 and some problems to get it to work
> > > > > > > > ...
> > > > > > > >
> > > > > > > > yummed all the ivtv parts for FC4
> > > > > > > >
> > > > > > > > lspci -v gives:
> > > > > > > > 00:08.0 Multimedia video controller: Internext
> > > > > > > > Compression Inc iTVC16 (CX23416) MPEG-2 Encoder (rev
> > > > > > > > 01) Subsystem: Unknown device ffab:0600
> > > > > > > > Flags: bus master, medium devsel, latency
> > > > > > > > 64, IRQ 11 Memory at dc000000 (32-bit, prefetchable)
> > > > > > > > [size=64M] Capabilities: [44] Power Management version
> > > > > > > > 2
> > > > > > > >
> > > > > > > > dmesg gives:
> > > > > > > > ivtv: ==================== START INIT IVTV
> > > > > > > > ==================== ivtv: version 0.4.3 (tagged
> > > > > > > > release) loading
> > > > > > > > ivtv: Linux version: 2.6.15-1.1833_FC4 686 REGPARM
> > > > > > > > 4KSTACKS gcc-4.0 ivtv: In case of problems please
> > > > > > > > include the debug info between ivtv: the START INIT
> > > > > > > > IVTV and END INIT IVTV lines, along with ivtv: any
> > > > > > > > module options, when mailing the ivtv-users
> > > > > > > > mailinglist. ivtv0: Unknown card: vendor/device:
> > > > > > > > 4444/0016 ivtv0:
> > > > > > > > subsystem vendor/device: ffab/0600 ivtv0:
> > > > > > > > cx23416 based
> > > > > > > > ivtv0: Defaulting to WinTV PVR 250 card
> > > > > > > > ivtv0: Please mail the vendor/device and subsystem
> > > > > > > > vendor/device IDs and what kind of
> > > > > > > > ivtv0: card you have to the ivtv-devel mailinglist
> > > > > > > > (www.ivtvdriver.org) ivtv0: Prefix your subject line
> > > > > > > > with [UNKNOWN CARD].
> > > > > > > > ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKA] ->
> > > > > > > > GSI 11 (level, low) -> IRQ 11
> > > > > > > > tveeprom: Encountered bad packet header [ff]. Corrupt
> > > > > > > > or not a Hauppauge eeprom.
> > > > > > > > ivtv0: i2c attach to card #0 ok [client=tveeprom,
> > > > > > > > addr=50] ivtv0: No tuner detected, default to NTSC
> > > > > > > > ivtv0 warning: i2c client addr: 0x21 not found for
> > > > > > > > command 0x8004646b! ivtv0: loaded v4l-cx2341x-enc.fw
> > > > > > > > firmware (262144 bytes) ivtv0: Encoder revision:
> > > > > > > > 0x02050032
> > > > > > > > ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768
> > > > > > > > buffers (4096KB total) ivtv0: Allocate DMA encoder YUV
> > > > > > > > stream: 194 x 10800 buffers (2048KB total) ivtv0:
> > > > > > > > Allocate DMA encoder VBI stream: 120 x 17472 buffers
> > > > > > > > (2048KB total) ivtv0: Allocate DMA encoder PCM audio
> > > > > > > > stream: 455 x 4608 buffers (2048KB total) ivtv0
> > > > > > > > warning: i2c client addr: 0x00 not found for command
> > > > > > > > 0x40045403! ivtv0 warning: i2c client addr: 0x21 not
> > > > > > > > found for command 0x40085618! ivtv0 warning: i2c client
> > > > > > > > addr: 0x21 not found for command 0xc0045627! ivtv0
> > > > > > > > warning: i2c client addr: 0x40 not found for command
> > > > > > > > 0x40086d11! ivtv0 warning: i2c client addr: 0x40 not
> > > > > > > > found for command 0x80287610! ivtv0 warning: i2c client
> > > > > > > > addr: 0x40 not found for command 0x40287611! ivtv0
> > > > > > > > warning: i2c client addr: 0x00 not found for command
> > > > > > > > 0x40085618! ivtv0 warning: i2c client addr: 0x40 not
> > > > > > > > found for command 0x40085618! ivtv0 warning: i2c client
> > > > > > > > addr: 0x21 not found for command 0x40085618! ivtv0
> > > > > > > > warning: i2c client addr: 0x40 not found for command
> > > > > > > > 0x80287610! ivtv0 warning: i2c client addr: 0x40 not
> > > > > > > > found for command 0x40287611! ivtv0 warning: i2c client
> > > > > > > > addr: 0x21 not found for command 0x40045613! ivtv0
> > > > > > > > warning: i2c client addr: 0x00 not found for command
> > > > > > > > 0x402c5639! ivtv0 warning: i2c client addr: 0x40 not
> > > > > > > > found for command 0x402c5639! ivtv0 warning: i2c client
> > > > > > > > addr: 0x21 not found for command 0x40045612! ivtv0
> > > > > > > > warning: i2c client addr: 0x40 not found for command
> > > > > > > > 0x80287610! ivtv0 warning: i2c client addr: 0x40 not
> > > > > > > > found for command 0x40287611! ivtv0: Initialized WinTV
> > > > > > > > PVR 250, card #0 ivtv: ==================== END INIT
> > > > > > > > IVTV
> > > > > > > > ====================
> > > > > > > >
> > > > > > > > As I mentioned I reinstalled the firmware parts as per
> > > > > > > > the "Howto" and some got better. But still gives me a
> > > > > > > > bunch of problems.
> > > > > > > >
> > > > > > > > Any pointers ??
> > > > > > >
> > > > > > > _______________________________________________
> > > > > > > ivtv-users mailing list
> > > > > > > [email protected]
> > > > > > > http://ivtvdriver.org/mailman/listinfo/ivtv-users
> > > > >
> > > > > _______________________________________________
> > > > > ivtv-users mailing list
> > > > > [email protected]
> > > > > http://ivtvdriver.org/mailman/listinfo/ivtv-users
> > >
> > > _______________________________________________
> > > ivtv-users mailing list
> > > [email protected]
> > > http://ivtvdriver.org/mailman/listinfo/ivtv-users
>
> _______________________________________________
> ivtv-users mailing list
> [email protected]
> http://ivtvdriver.org/mailman/listinfo/ivtv-users
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
