| Hi I have a Hauppauge PVR-150 (model 1062) running under Ubuntu Breezy (5.10) (i386 NOT amd64 version) with ubuntu's kernel 2.6.12-10-386 on a MSI K8T Neo (Via K8T800 chipset) motherboard. I have tried ivtv version 0.4.0, 0.4.4, and the latest svn tarball from the 0.4 branch, but keep getting the same i2c errors like this in dmesg: ivtv0 warning: i2c client addr: 0x44 not found for command 0xc008561c! ivtv correctly identifies the card and creates /dev/video0 etc, however when I try to read the mpeg stream with "cat /dev/video0" i get no mpeg stream and this in dmesg: [4297655.072000] ivtv0 warning: i2c client addr: 0x44 not found for command 0xc0cc5605! [4297655.552000] ivtv0 warning: i2c client addr: 0x44 not found for command 0x40045613! [4297655.552000] ivtv0 warning: i2c client addr: 0x44 not found for command 0x40045612! When I tried 0.4.4 | got this as part of my dmesg: [4294707.422000] tveeprom: tuner = <unknown> (idx = 112, type = 4) but in the latest 0.4 svn: [4295967.902000] tveeprom: tuner = TCL M2523_5N_E (idx = 112, type = 50) This is the "lspci -v" output: 0000:00:08.0 Multimedia video controller: Internext Compression Inc iTVC16 (CX23416) MPEG-2 Encoder (rev 01) Subsystem: Hauppauge computer works Inc.: Unknown device 8801 Flags: bus master, medium devsel, latency 64, IRQ 19 Memory at c8000000 (32-bit, prefetchable) [size=64M] Capabilities: [44] Power Management version 2 Here is the full dmesg output: [4295967.858000] ivtv: ==================== START INIT IVTV ==================== [4295967.858000] ivtv: version 0.4.5 (development snapshot compiled on Fri 28 Apr 2006 10:30:01 PM PDT) loading [4295967.858000] ivtv: Linux version: 2.6.12-10-386 386 gcc-3.4 [4295967.858000] ivtv: In case of problems please include the debug info between [4295967.858000] ivtv: the START INIT IVTV and END INIT IVTV lines, along with [4295967.859000] ivtv: any module options, when mailing the ivtv-users mailinglist. [4295967.861000] ivtv0: Autodetected WinTV PVR 150 card (cx23416 based) [4295967.862000] ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 19 (level, low) -> IRQ 19 [4295967.902000] tveeprom: ivtv version [4295967.902000] tveeprom: Hauppauge: model = 26582, rev = F0B2, serial# = 9448199 [4295967.902000] tveeprom: tuner = TCL M2523_5N_E (idx = 112, type = 50) [4295967.902000] tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) [4295967.902000] tveeprom: audio processor = CX25843 (type = 25) [4295967.902000] tveeprom: decoder processor = CX25843 (type = 1e) [4295967.902000] ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] [4295967.918000] tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 [4295967.918000] ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] [4295968.074000] wm8775 0-001b: ivtv driver [4295968.074000] wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0) [4295968.081000] ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b] [4295968.127000] ivtv0 warning: i2c client addr: 0x44 not found for command 0xc008561c! [4295968.809000] ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) [4295969.029000] ivtv0: Encoder revision: 0x02050032 [4295969.030000] ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) [4295969.032000] ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) [4295969.034000] ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) [4295969.035000] ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) [4295969.036000] tuner: type set to 50 (TCL 2002N) by ivtv i2c driver #0 [4295969.036000] ivtv0 warning: i2c client addr: 0x44 not found for command 0x40085618! [4295969.036000] ivtv0 warning: i2c client addr: 0x44 not found for command 0xc0045627! [4295969.039000] ivtv0 warning: i2c client addr: 0x44 not found for command 0x40046d11! [4295969.039000] ivtv0 warning: i2c client addr: 0x44 not found for command 0x40085618! [4295969.039000] ivtv0 warning: i2c client addr: 0x44 not found for command 0xc008561c! [4295969.039000] ivtv0 warning: i2c client addr: 0x44 not found for command 0x40045613! [4295969.042000] ivtv0 warning: i2c client addr: 0x44 not found for command 0x402c5639! [4295969.042000] ivtv0 warning: i2c client addr: 0x44 not found for command 0x40045612! [4295969.142000] ivtv0 warning: i2c client addr: 0x44 not found for command 0xc008561c! [4295969.142000] ivtv0: Initialized WinTV PVR 150, card #0 [4295969.142000] ivtv: ==================== END INIT IVTV ==================== Thanks for your help! -Ed |
_______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
