Hello, Subject Line Says It All! (And yes, there is a working cable tv connection connected to the tuner input on the card...) I will try to include the following information: Linux video capture interface: v1.00 ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.6.1 (development snapshot compiled on Wed Mar 29 20:30:52 2006) loading ivtv: Linux version: 2.6.16-1.2069_FC4 686 REGPARM 4KSTACKS gcc-4.0 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 ivtv0: Unreasonably low latency timer, setting to 64 (was 32) tveeprom 1-0050: Hauppauge model 26582, rev F0B2, serial# 9307519 tveeprom 1-0050: tuner model is TCL M2523_5N_E (idx 112, type 4) tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 1-0050: audio processor is CX25843 (idx 37) tveeprom 1-0050: decoder processor is CX25843 (idx 30) tveeprom 1-0050: has no radio, has no IR remote tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0) cx25840 1-0044: loaded v4l-cx25840.fw firmware (13353 bytes) wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0) ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02040024 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) tuner 1-0061: tuner type not set tuner 1-0061: tuner type not set ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ====================
Output from the following command yields, ivtvctl --log-status ioctl VIDIOC_LOG_STATUS ok ivtv0: ================= START STATUS CARD #0 ================= tveeprom 1-0050: Hauppauge model 26582, rev F0B2, serial# 9307519 tveeprom 1-0050: tuner model is TCL M2523_5N_E (idx 112, type 4) tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 1-0050: audio processor is CX25843 (idx 37) tveeprom 1-0050: decoder processor is CX25843 (idx 30) tveeprom 1-0050: has no radio, has no IR remote tuner 1-0061: Tuner mode: analog TV tuner 1-0061: Frequency: 67.25 MHz tuner 1-0061: Standard: 0x0000b000 cx25840 1-0044: Video signal: not present cx25840 1-0044: Detected format: NTSC-M cx25840 1-0044: Detected audio mode: forced mode cx25840 1-0044: Detected audio standard: forced audio standard cx25840 1-0044: Audio muted: no cx25840 1-0044: Audio microcontroller: running cx25840 1-0044: Configured audio standard: BTSC cx25840 1-0044: Configured audio mode: undefined cx25840 1-0044: Specified standard: NTSC-M cx25840 1-0044: Specified video input: Composite 7 cx25840 1-0044: Specified audio input: Tuner (In8) cx25840 1-0044: Specified audioclock freq: 48000 Hz cx25840 1-0044: Preferred audio mode: stereo cx25840 1-0044: Selected 65 MHz format: system DK cx25840 1-0044: Selected 45 MHz format: chroma wm8775 1-001b: Input: 2 ivtv0: ================== END STATUS CARD #0 ================== I haved used the following commands to test the driver: # cat /dev/video0 > /tmp/test_capture.mpg # mplayer /tmp/test_capture.mpg All I get is a screen of static and the sound track is the sound of static. Any help or guidance would be greatly appreciated. Thanks, John _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
