Is this still happening with the 0.4.5 driver? Dustin
On 27-Apr-06, at 5:31 PM, Martin Harte wrote: > Hi All, > I'm having problems with my pvr250 in that I am only receiving a > single channel with no sound, and seem to be unable to access any of > the other channels. > > I change the frequency of the device using ptune-ui.pl, while viewing > /dev/video0 with mplayer, but the video stream being displayed > continues to stay the same, and does not change when I change around > the channels. > > I have tried this for every combination of settings in ptune-ui and am > at a loss. > > Any suggestions would be much appreciated. > > Thanks, > Martin. > > Below is the log output for my device. > > ivtv: ==================== START INIT IVTV ==================== > ivtv: version 0.4.4 (tagged release) loading > ivtv: Linux version: 2.4.27 > ivtv: In case of problems please include the debug info between > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > ivtv: any module options, when mailing the ivtv-users mailinglist. > ivtv0: Autodetected WinTV PVR 250 card (cx23416 based) > tveeprom: ivtv version > tveeprom: Hauppauge: model = 32055, rev = B135, serial# = 7396931 > tveeprom: tuner = Temic 4066FY5 (idx = 35, type = 18) > tveeprom: tuner fmt = PAL(I) (eeprom = 0x10, v4l2 = 0x00000010) > tveeprom: audio processor = MSP4418 (type = 19) > tveeprom: decoder processor = SAA7115 (type = 13) > ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] > i2c-core.o: client [tveeprom] registered to adapter [ivtv i2c driver > #0](pos. 0) > . > tuner: chip found @ 0xc2 > ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] > i2c-core.o: client [(tuner unset)] registered to adapter [ivtv i2c > driver #0](po > s. 1). > saa7115 0-0021: ivtv driver > saa7115 0-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) > ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21] > i2c-core.o: client [saa7115] registered to adapter [ivtv i2c driver > #0](pos. 2). > msp34xx: init: chip=MSP3418W-B3 +nicam +simple +radio > msp3410: daemon started > ivtv0: i2c attach to card #0 ok [client=MSP3418W-B3, addr=40] > i2c-core.o: client [MSP3418W-B3] registered to adapter [ivtv i2c > driver #0](pos. > 3). > i2c-core.o: adapter ivtv i2c driver #0 registered as adapter 0. > remove_proc_entry: ivtv0/loading busy, count=1 > remove_proc_entry: firmware/ivtv0 busy, count=1 > ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) > de_put: deferred delete of loading > de_put: deferred delete of ivtv0 > ivtv0: Encoder revision: 0x02050032 > ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB > total) > ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB > total) > ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB > total) > ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers > (2048KB total) > tuner: type set to 18 (Temic PAL_I (4066 FY5)) > ivtv0: Initialized WinTV PVR 250, card #0 > ivtv: ==================== END INIT IVTV ==================== > > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users > _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
