Hi List,
i just upgraded my 10.0 to 10.1 and can't get my PVR-250 to work correctly.
(driver 0.7.0 from oss version of 10.1)
All input works, expect the television. When i tune to a valid frequency i
only get a inputsignal that looks like the antenna is unpluged.
When i reboot the system to 10.0 everything works perfectly (old driver
version 0.3.7). So it's not a wiring/antenna problem.
The init of the card looks perfect to me
(i put sa7115 and tveeprom already to debug)
---------------------------
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.7.0 (development snapshot compiled on Wed May 3 13:12:51
2006) loading
ivtv: Linux version: 2.6.16.13-4-default 586 REGPARM gcc-4.1
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 22 (level, low) -> IRQ 217
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
msp3400 1-0040: MSP4418G-A2 found @ 0x80 (ivtv i2c driver #0)
msp3400 1-0040: MSP4418G-A2 supports nicam and radio, mode is autodetect and
autoselect
saa7115 1-0021: detecting saa7115 client on address 0x42
saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
saa7115 1-0021: writing init values
saa7115 1-0021: set audio clock freq: 48000
saa7115 1-0021: status: (1E) 0x48, (1F) 0xc0
tveeprom 1-0050: full 256-byte eeprom dump:
tveeprom 1-0050: 00: 84 09 00 04 20 77 00 40 47 7a 6d 00 73 05 99 00
tveeprom 1-0050: 10: 84 08 00 06 36 7d 00 00 18 15 89 72 07 70 73 09
tveeprom 1-0050: 20: 13 5f 73 0a 04 30 74 0b 98 18 0c 72 0f 01 72 10
tveeprom 1-0050: 30: 01 72 11 00 79 9a 00 00 00 00 00 00 00 00 00 00
tveeprom 1-0050: 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
tveeprom 1-0050: 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
tveeprom 1-0050: 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
tveeprom 1-0050: 70: 00 00 00 00 00 00 00 00 00 00 00 00 13 eb 00 70
tveeprom 1-0050: 80: 84 09 00 04 20 77 00 40 47 7a 6d 00 73 05 99 00
tveeprom 1-0050: 90: 84 08 00 06 36 7d 00 00 18 15 89 72 07 70 73 09
tveeprom 1-0050: a0: 13 5f 73 0a 04 30 74 0b 98 18 0c 72 0f 01 72 10
tveeprom 1-0050: b0: 01 72 11 00 79 9a 00 00 00 00 00 00 00 00 00 00
tveeprom 1-0050: c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
tveeprom 1-0050: d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
tveeprom 1-0050: e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
tveeprom 1-0050: f0: 00 00 00 00 00 00 00 00 00 00 00 00 13 eb 00 70
tveeprom 1-0050: Tag [04] + 8 bytes: 20 77 00 40 47 7a 6d 00
tveeprom 1-0050: Tag [05] + 2 bytes: 99 00
tveeprom 1-0050: Tag [06] + 7 bytes: 36 7d 00 00 18 15 89
tveeprom 1-0050: Tag [07] + 1 bytes: 70
tveeprom 1-0050: Tag [09] + 2 bytes: 13 5f
tveeprom 1-0050: Tag [0a] + 2 bytes: 04 30
tveeprom 1-0050: Tag [0b] + 3 bytes: 98 18 0c
tveeprom 1-0050: Tag [0f] + 1 bytes: 01
tveeprom 1-0050: Tag [10] + 1 bytes: 01
tveeprom 1-0050: Not sure what to do with tag [10]
tveeprom 1-0050: Tag [11] + 1 bytes: 00
tveeprom 1-0050: Not sure what to do with tag [11]
tveeprom 1-0050: Hauppauge model 32054, rev B148, serial# 7174727
tveeprom 1-0050: tuner model is LG TP18PSB11D (idx 48, type 29)
tveeprom 1-0050: TV standards PAL(B/G) (eeprom 0x04)
tveeprom 1-0050: audio processor is MSP4418 (idx 25)
tveeprom 1-0050: decoder processor is SAA7115 (idx 19)
tveeprom 1-0050: has no radio, has IR remote
ivtv0: Corrected autodetection from Hauppauge WinTV PVR-150 to Hauppauge WinTV
PVR-250
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
total)
tuner 1-0061: type set to 29 (LG PAL_BG (TPI8PSB11D))
saa7115 1-0021: disable output
saa7115 1-0021: decoder set input 4
saa7115 1-0021: now setting Composite input
saa7115 1-0021: enable output
saa7115 1-0021: decoder set standard 50 Hz
saa7115 1-0021: set audio clock freq: 48000
saa7115 1-0021: disable output
saa7115 1-0021: enable output
ivtv0: Initialized Hauppauge WinTV PVR-250, card #0
ivtv: ==================== END INIT IVTV ====================
saa7115 1-0021: disable output
saa7115 1-0021: enable output
saa7115 1-0021: disable output
saa7115 1-0021: enable output
saa7115 1-0021: status: 0xc0
saa7115 1-0021: disable output
saa7115 1-0021: decoder set input 1
saa7115 1-0021: now setting Composite input
saa7115 1-0021: enable output
saa7115 1-0021: disable output
saa7115 1-0021: decoder set input 4
saa7115 1-0021: now setting Composite input
saa7115 1-0021: enable output
saa7115 1-0021: disable output
saa7115 1-0021: enable output
-----------------------------
Has someone run into the same problem and know how to fix it ?
Maybe driver up/downgrade ?
Thanks for any help,
Paul
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
