Okay well i've gotten modprobe to load ivtv, however if i do ivtv-tune -c 3, and try to capture video from there or watch it in mplayer it doesn't work, i get pure black screen.
There seems to be some errors in my init though: ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.7.0 (tagged release) loading ivtv: Linux version: 2.6.17-rc6 SMP preempt mod_unload PENTIUM4 gcc-4.1 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) ACPI: PCI Interrupt 0000:03:05.0[A] -> GSI 21 (level, low) -> IRQ 20 tveeprom 0-0050: Hauppauge model 26032, rev C199, serial# 8181946 tveeprom 0-0050: tuner model is TCL 2002N 5H (idx 99, type 50) tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 0-0050: audio processor is CX25841 (idx 35) tveeprom 0-0050: decoder processor is CX25841 (idx 28) tveeprom 0-0050: has no radio, has IR remote tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) ivtv0: Failed to load module cx25840 ivtv0: Failed to load module wm8775 ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02050032 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) tuner 0-0061: type set to 50 (TCL 2002N) ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: i2c addr 0x44 not found for command 0x4008646f! ivtv0: i2c hardware 0x00000020 not found for command 0x4008646d! ivtv0: i2c hardware 0x00000001 not found for command 0x4008646d! ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== Any ideas? Thanks! George Mito Tranin - Lists wrote: > Sam Varshavchik wrote: >> George Nychis writes: >> >>> Hey guys, >>> >>> I run a 2.6.17-rc6 kernel and ivtv-0.7.0. I was wondering if anyone >>> else has gotten mythtv working with ivtv-0.7.0? If so, what card? I >>> have a PVR-150 and can't get mythtv working with it. >> Works fine with my PVR-350. > > I have mine working with video, but ever since upgrading to 0.7.0 I > haven't been able to get the sound to work. > _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
