[ivtv-users] ivtv 0.7.0, Kernel 2.6.17-1.2124_FC4 No Sound

[Weltobills]

Title: Message

Sorry to as what is probably a stupid question but here goes.  How do I run the commands to get to here;

 

│ Symbol: VIDEO_MSP3400 [=m] │
│ Prompt: Micronas MSP34xx audio decoders │
│ Defined at drivers/media/video/Kconfig:341 │
│ Depends on: VIDEO_DEV && I2C │
│ Location: │
│ -> Device Drivers │
│ -> Multimedia devices │
│ -> Video Capture Adapters │
│ -> Encoders and Decoders │
│ Selected by: VIDEO_BT848 && VIDEO_DEV && PCI && I2C && VIDEO_V4L2 │

I just need a little more direction on this one.  BTW, I renamed the msp3400.ko to msp3400.ko.orig.  I then renamed it back, rebooted and I get the same message in dmesg.  The line I see is "ivtv0: Failed to load module msp3400".  Are you saying that should load once I enable it with the commands above?

 

ivtv:  ==================== START INIT IVTV ====================
ivtv:  version 0.7.0 (tagged release) loading
ivtv:  Linux version: 2.6.17-1.2142_FC4 mod_unload 686 REGPARM 4KSTACKS gcc-4.0
ivtv:  In case of problems please include the debug info between
ivtv:  the START INIT IVTV and END INIT IVTV lines, along with
ivtv:  any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge WinTV PVR-350 card (cx23415 based)
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 193
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
tveeprom 0-0050: Hauppauge model 48132, rev K268, serial# 8051829
tveeprom 0-0050: tuner model is LG TAPE H001F MK3 (idx 68, type 47)
tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 0-0050: audio processor is MSP4448 (idx 27)
tveeprom 0-0050: decoder processor is SAA7115 (idx 19)
tveeprom 0-0050: has radio, has IR remote
tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
tda9887 0-0043: chip found @ 0x86 (ivtv i2c driver #0)
saa7115 0-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
saa7127 0-0044: saa7129 found @ 0x88 (ivtv i2c driver #0)
ivtv0: Failed to load module msp3400
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Decoder revision: 0x02020023
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv0: Create encoder radio stream
ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total)
ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total)
ivtv0: Create decoder VOUT stream
ivtv0: Allocate DMA decoder YUV stream: 24 x 43200 buffers (1024KB total)
ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes)
tuner 0-0061: type set to 47 (LG NTSC (TAPE series))
ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000008 not found for command 0x4008646d!
ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c!
ivtv0: Initialized Hauppauge WinTV PVR-350, card #0
ivtv:  ====================  END INIT IVTV  ====================

--
No virus found in this outgoing message.
Checked by AVG Free Edition.
Version: 7.1.405 / Virus Database: 268.10.10/418 - Release Date: 8/14/2006

_______________________________________________
ivtv-users mailing list
ivtv-users@ivtvdriver.org
http://ivtvdriver.org/mailman/listinfo/ivtv-users