Hello, since I changed from SuSE 10.0 to 10.1, I have the problem to use my Hauppauge 250-card. Here are the initialisation messages:
<6>ivtv: ==================== START INIT IVTV ==================== <6>ivtv: version 0.6.2 (tagged release) loading <6>ivtv: Linux version: 2.6.16.21 PENTIUM4 REGPARM gcc-4.1 <6>ivtv: In case of problems please include the debug info between <6>ivtv: the START INIT IVTV and END INIT IVTV lines, along with <6>ivtv: any module options, when mailing the ivtv-users mailinglist. <6>ivtv0: Autodetected Hauppauge WinTV PVR-250 card (cx23415 based) <6>ACPI: PCI Interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 22 <6>ivtv0: Unreasonably low latency timer, setting to 64 (was 32) <6>msp3400 1-0040: MSP18415O-C31 found @ 0x80 (ivtv i2c driver #0) <6>msp3400 1-0040: MSP18415O-C31 supports nicam and radio, mode is autodetect and autoselect <4>tveeprom 1-0050: Encountered bad packet header [87]. Corrupt or not a Hauppauge eeprom. <6>ivtv0: No tuner detected, default to NTSC <6>ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) <6>ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) <6>ivtv0: Encoder revision: 0x02050032 <6>ivtv0: Decoder revision: 0x02020023 <6>ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) <6>ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) <6>ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) <6>ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) <3>ivtv0: i2c addr 0x21 not found for command 0x40045613! <3>ivtv0: i2c addr 0x21 not found for command 0xc0045627! <3>ivtv0: i2c addr 0x21 not found for command 0x40045612! <3>ivtv0: i2c addr 0x21 not found for command 0x40045613! <3>ivtv0: i2c addr 0x21 not found for command 0x40045612! <6>ivtv0: Initialized Hauppauge WinTV PVR-250, card #0 <6>ivtv: ==================== END INIT IVTV ==================== and my module.conf: --------------------module.conf------------------- alias char-major-81 videodev alias char-major-81-0 ivtv options ivtv ivtv_debug=1 tuner=5 options msp3400 once=1 install ivtv /sbin/modprobe msp3400; /sbin/modprobe saa7115; /sbin/modprobe tuner; /sbin/modprobe --ignore-install ivtv remove ivtv /sbin/modprobe -r --ignore-remove ivtv; /sbin/modprobe -r msp3400; /sbin/modprobe -r saa7115; /sbin/modprobe -r tuner install bttv echo disable --------------------------------------------------------- I`ve no idea! Bye ...Juergen _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
