On Jun 22, 2006, at 11:34 AM, Jürgen Brumberg wrote: > Hello, > > since I changed from SuSE 10.0 to 10.1, I have the problem to use my > Hauppauge 250-card. > Here are the initialisation messages: > > <6>ivtv: ==================== START INIT IVTV ==================== > <6>ivtv: version 0.6.2 (tagged release) loading > <6>ivtv: Linux version: 2.6.16.21 PENTIUM4 REGPARM gcc-4.1 > <6>ivtv: In case of problems please include the debug info between > <6>ivtv: the START INIT IVTV and END INIT IVTV lines, along with > <6>ivtv: any module options, when mailing the ivtv-users mailinglist. > <6>ivtv0: Autodetected Hauppauge WinTV PVR-250 card (cx23415 based) > <6>ACPI: PCI Interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> > IRQ 22 > <6>ivtv0: Unreasonably low latency timer, setting to 64 (was 32) > <6>msp3400 1-0040: MSP18415O-C31 found @ 0x80 (ivtv i2c driver #0) > <6>msp3400 1-0040: MSP18415O-C31 supports nicam and radio, mode is > autodetect and autoselect > <4>tveeprom 1-0050: Encountered bad packet header [87]. Corrupt or > not a > Hauppauge eeprom. > <6>ivtv0: No tuner detected, default to NTSC > <6>ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) > <6>ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) > <6>ivtv0: Encoder revision: 0x02050032 > <6>ivtv0: Decoder revision: 0x02020023 > <6>ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers > (4096KB > total) > <6>ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB > total) > <6>ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB > total) > <6>ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers > (2048KB > total) > <3>ivtv0: i2c addr 0x21 not found for command 0x40045613! > <3>ivtv0: i2c addr 0x21 not found for command 0xc0045627! > <3>ivtv0: i2c addr 0x21 not found for command 0x40045612! > <3>ivtv0: i2c addr 0x21 not found for command 0x40045613! > <3>ivtv0: i2c addr 0x21 not found for command 0x40045612! > <6>ivtv0: Initialized Hauppauge WinTV PVR-250, card #0 > <6>ivtv: ==================== END INIT IVTV ==================== > > and my module.conf: > > --------------------module.conf------------------- > alias char-major-81 videodev > alias char-major-81-0 ivtv > options ivtv ivtv_debug=1 tuner=5 > options msp3400 once=1 > install ivtv /sbin/modprobe msp3400; /sbin/modprobe saa7115; /sbin/ > modprobe > tuner; /sbin/modprobe --ignore-install ivtv > remove ivtv /sbin/modprobe -r --ignore-remove ivtv; /sbin/modprobe -r > msp3400; /sbin/modprobe -r saa7115; /sbin/modprobe -r tuner > install bttv echo disable > ---------------------------------------------------------
Get rid of everything in module.conf, except for the two alias lines and try again. It might not work, but at least you'll be letting it try to figure things out on its own. Keith C > > I`ve no idea! > > Bye ...Juergen > > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
