Hello imy, which vanilla sources did you use now?
I have same problems using kernel-2.6.17-r7 with 350 PVR! By Holger Am Sonntag, 10. September 2006 18:09 schrieb imy: > I posted my problem in a forum and after 15 min I get the tip to emerge a > vanilla kernel. Now it works! > > > ----- Original Message ----- > From: "imy" <[EMAIL PROTECTED]> > To: "User discussion about IVTV" <[email protected]> > Sent: Sunday, September 10, 2006 1:20 PM > Subject: Re: [ivtv-users] PVR 350, ivtv 07, kernel 2.6.17-r7,loading of > modules fails > > > I emerged now vdr and pvrinput, using the same channel.conf, that works > > with > > > my previous installation. At the end of the system log file: > > > > Sep 10 13:11:54 digi ivtv0: i2c hardware 0x00000008 not found for command > > 0xc008561c! > > Sep 10 13:11:55 digi ivtv0: i2c addr 0x21 not found for command > > 0x40045613! > > > Sep 10 13:11:55 digi ivtv0: i2c addr 0x21 not found for command > > 0x40045612! > > > Sep 10 13:11:55 digi ivtv0: i2c hardware 0x00000008 not found for command > > 0xc008561c! > > Sep 10 13:12:47 digi ivtv0: i2c hardware 0x00000008 not found for command > > 0xc008561c! > > Sep 10 13:12:47 digi ivtv0: i2c hardware 0x00000008 not found for command > > 0xc008561c! > > > > Every time I zap two new lines of this kind appears: > > > > Sep 10 13:13:06 digi ivtv0: i2c hardware 0x00000008 not found for command > > 0xc008561c! > > Sep 10 13:13:06 digi ivtv0: i2c hardware 0x00000008 not found for command > > 0xc008561c! > > > > Could this indicate where the problem is? If this could help: I've an > > Epia SP 13000 mainboard. I've a dual boot with the working ivtv 0.4 and > > an earlier kernel on another partition where all works without problems. > > > > ----- Original Message ----- > > From: "imy" <[EMAIL PROTECTED]> > > To: "User discussion about IVTV" <[email protected]> > > Sent: Saturday, September 09, 2006 3:46 PM > > Subject: Re: [ivtv-users] PVR 350, ivtv 07, kernel 2.6.17-r7,loading of > > modules fails > > > > > I removed autoloading the modules from > > /etc/modules.autoload.d/kernel-2.6, > > > > rebooted the machine. > > > > > > The complete init-section modprobe ivtv: > > > > > > ivtv: ==================== START INIT IVTV ==================== > > > ivtv: version 0.7.0 (tagged release) loading > > > ivtv: Linux version: 2.6.17-gentoo-r7 mod_unload VIAC3-2 REGPARM > > gcc-4.1 > > > > ivtv: In case of problems please include the debug info between > > > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > > > ivtv: any module options, when mailing the ivtv-users mailinglist. > > > ivtv0: Autodetected Hauppauge WinTV PVR-350 card (cx23415 based) > > > ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LNKA] -> GSI 10 (level, > > > > low) -> > > > > > IRQ 10 > > > ivtv0: Unreasonably low latency timer, setting to 64 (was 32) > > > ivtv0: Failed to load module tveeprom > > > tveeprom 1-0050: Hauppauge model 48134, rev J342, serial# 7067564 > > > tveeprom 1-0050: tuner model is Temic 4009FR5 (idx 42, type 20) > > > tveeprom 1-0050: TV standards PAL(B/G) (eeprom 0x04) > > > tveeprom 1-0050: audio processor is MSP4418 (idx 25) > > > tveeprom 1-0050: decoder processor is SAA7115 (idx 19) > > > tveeprom 1-0050: has radio, has IR remote > > > ivtv0: Failed to load module tuner > > > ivtv0: Failed to load module tda9887 > > > ivtv0: Failed to load module saa7115 > > > ivtv0: Failed to load module saa7127 > > > ivtv0: Failed to load module msp3400 > > > ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) > > > ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) > > > ivtv0: Encoder revision: 0x02050032 > > > ivtv0: Decoder revision: 0x02020023 > > > ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB > > > > total) > > > > > ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB > > total) > > > > ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB > > total) > > > > ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers > > > (2048KB total) > > > ivtv0: Create encoder radio stream > > > ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB > > total) > > > > ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB > > total) > > > > ivtv0: Create decoder VOUT stream > > > ivtv0: Allocate DMA decoder YUV stream: 20 x 51840 buffers (1024KB > > total) > > > > ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes) > > > ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c! > > > ivtv0: i2c addr 0x21 not found for command 0x4008646f! > > > ivtv0: i2c hardware 0x00000008 not found for command 0x4008646d! > > > ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c! > > > ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c! > > > ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c! > > > ivtv0: Initialized Hauppauge WinTV PVR-350, card #0 > > > ivtv: ==================== END INIT IVTV ==================== > > > > > > > > > > > > > > > ----- Original Message ----- > > > From: "Sander Sweers" <[EMAIL PROTECTED]> > > > To: "User discussion about IVTV" <[email protected]> > > > Sent: Saturday, September 09, 2006 3:10 PM > > > Subject: Re: [ivtv-users] PVR 350, ivtv 07, kernel 2.6.17-r7, loading > > > of modules fails > > > > > > > ilmusy wrote: > > > > > Hi, > > > > > > > > > > I have installed gentoo 2.6.17-r7 on a new harddisk. It's a very > > > > minimal > > > > > installation, no X or other big apps so far. > > > > > > > > I've installed a PVR 350. > > > > > > > > > > Then I've installed ivtv 0.70. > > > > > > > > You did use the build from portage? > > > > > > > > > I know, that modules are build by the kernel with the current > > > > > kernel > > > > and > > > > > enabled them in the config. My config is mainly a copy of a gentoo > > 2.6.14 > > > > version, where my card has running. > > > > > > > > But with "modprobe ivtv" loading of some modules fails: > > > > > > > > > > > > > > > saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) > > > > > saa7127 1-0044: saa7127 found @ 0x88 (ivtv i2c driver #0) > > > > > msp3400 1-0040: MSP4418G-A2 found @ 0x80 (ivtv i2c driver #0) > > > > > msp3400 1-0040: MSP4418G-A2 supports nicam and radio, mode is > > > > autodetect > > > > > and autoselect > > > > > > > > ivtv0: Failed to load module tveeprom > > > > > tveeprom 1-0050: Hauppauge model 48134, rev J342, serial# 7067564 > > > > > tveeprom 1-0050: tuner model is Temic 4009FR5 (idx 42, type 20) > > > > > tveeprom 1-0050: TV standards PAL(B/G) (eeprom 0x04) > > > > > tveeprom 1-0050: audio processor is MSP4418 (idx 25) > > > > > tveeprom 1-0050: decoder processor is SAA7115 (idx 19) > > > > > tveeprom 1-0050: has radio, has IR remote > > > > > ivtv0: Failed to load module tuner > > > > > ivtv0: Failed to load module tda9887 > > > > > ivtv0: Failed to load module saa7115 > > > > > ivtv0: Failed to load module saa7127 > > > > > ivtv0: Failed to load module msp3400 > > > > > > > > I am uncertain why ivtv will try to load the modules if they are > > loaded > > > > > already? But there is no error as far as i can see, but you should > > > > include the whole ivtv init in your mail (see below). > > > > > > > > > The modules are in the folder: > > > > > > > > > > /lib/modules/2.6.17-gentoo-r7/kernel/drivers/media/video > > > > > > > > Good > > > > > > > > > I've put the modules in the file /etc/modules.autoload.d/kernel-2.6 > > to > > > > be autoloaded by startup: > > > > > tveeprom > > > > > tuner > > > > > tda9887 > > > > > saa7115 > > > > > saa7127 > > > > > msp3400 > > > > > > > > Why? Is there a reason you need these loaded on startup? If not > > > > please let ivtv load them. (This should not make any difference > > > > AFAIK) > > > > > > > > > And after reboot with lsmod I can see that the modules can be > > > > > found: > > > > > > > > > > Module Size Used by > > > > > msp3400 24896 0 > > > > > saa7127 9332 0 > > > > > saa7115 12112 0 > > > > > tda9887 13360 0 > > > > > tuner 43788 0 > > > > > tveeprom 12016 0 > > > > > > > > > > But when loading ivtv with modprobe loading of the modules still > > > > fails. > > > > > > > Please tell me where my mistake is. > > > > > > > > There are none except for not telling us if you even tried capturing > > > > from the pvr350 and not providing the complete ivtv init. > > > > > > > > You should always include the ivtv init from the logs. > > > > It starts with: > > > > ===== START STATUS CARD #0 ====== > > > > and ends with > > > > ====== END STATUS CARD #0 =======. > > > > Everything in between paste it in your e-mail. > > > > > > > > > Thank you > > > > > > > > Greets > > > > Sander > > > > > > > > _______________________________________________ > > > > ivtv-users mailing list > > > > [email protected] > > > > http://ivtvdriver.org/mailman/listinfo/ivtv-users > > > > > > _______________________________________________ > > > ivtv-users mailing list > > > [email protected] > > > http://ivtvdriver.org/mailman/listinfo/ivtv-users > > > > _______________________________________________ > > ivtv-users mailing list > > [email protected] > > http://ivtvdriver.org/mailman/listinfo/ivtv-users > > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users -- Bis dann Holger Radke Holger Radke Niel�nderweg 5 D - 48165 M�nster GERMANY Email: [EMAIL PROTECTED] Internet: - Voice: (++49) 2501 - 928622 Fax: (++49) - Mobil: (++49) 174 - 9212147
_______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
