Jerry Geis wrote: > I have downloaded 0.3.8 based on the 2.6.9 kernel for centos 4.4 (RHEL) > The kernel I am using has all the other TV cards in the kernel. > I have compiled 0.3.8 and installed it. > I downloaded the 060418 Amity3 drivers > and copied the two files into /lib/modules: > HcwMakoC.ROM > ivtv-fw-enc.bin > > I did a depmod and modprobe ivtv, dmesg shows it loaded successfully. > > I then tried "cat /dev/video0 | mplayer - " and all I get is static. > > I have compiled ivtv-tune, ran "ivtv-tune -c12 -d/dev/video0" > I ran ivtvctl -P and it reports I am using input 6 which is tuner 0. > > All i get is static. > > What am I missing. > > Jerry > > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users > > >
Sorry I should Have attached the dmesg output, Jerry ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.3.8 (tagged release) loading ivtv: Linux version: 2.6.9-42.0.2.plus.c4 686 REGPARM 4KSTACKS gcc-3.4 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 150 card (iTVC16 based) ACPI: PCI interrupt 0000:01:06.0[A] -> GSI 16 (level, low) -> IRQ 177 ivtv: Unreasonably low latency timer, setting to 64 (was 32) tveeprom: The eeprom says no radio is present, but the tuner type tveeprom: indicates otherwise. I will assume that radio is present. tveeprom: Hauppauge: model = 25012, rev = B168, serial# = 8319894 tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio processor = CX25843 (type = 25) tveeprom: decoder processor = CX25843 (type = 1e) ivtv: i2c attach to card #0 ok [client=tveeprom[50], addr=50] tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach to card #0 ok [client=(tuner unset), addr=61] cx25840: loading /lib/modules/HcwMakoA.ROM eth0: no IPv6 routers present ivtv: i2c attach to card #0 ok [client=cx25840[50], addr=44] ivtv: i2c attach to card #0 ok [client=wm8775[50], addr=1b] tda9885/6/7: chip found @ 0x86 ivtv: i2c attach to card #0 ok [client=tda9887, addr=43] ivtv: loading /lib/modules/ivtv-fw-enc.bin ivtv: Encoder revision: 0x02050032 ivtv warning: Encoder Firmware can be buggy, use version 0x02040011!!!! ivtv: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv: Create encoder radio stream tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0 ivtv: Initialized WinTV PVR 150, card #0 ivtv: ==================== END INIT IVTV ==================== _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
