All, I started with kernel 2.6.9 (centso 4.4) and ivtv 0.3.8. could not get that to work so I DUG in. Downloaded 2.6.18.1 kernel, downloaded 0.8.0 ivtv and started over. I think I have all the needed kernel items enabled, put the firmware in the right place, remove the old files etc... I am using NO module options. I am running on a x86_64 box.
when I run "cat /dev/video0 | mplayer -" all I get is static. I compiled ivtv-tune and did "ivtv-tune -c4 -d/dev/video0" ran the above command again and still static. Everything looks like it loaded correctly (see below). Any ideas on my next step? Thanks, Jerry. --------------------------------------------------------- Linux video capture interface: v2.00 ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.8.0 (tagged release) loading ivtv: Linux version: 2.6.18.1 mod_unload gcc-3.4 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 GSI 19 sharing vector 0xC9 and IRQ 19 ACPI: PCI Interrupt 0000:04:06.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 201 ivtv0: Unreasonably low latency timer, setting to 64 (was 32) ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) tveeprom 2-0050: The eeprom says no radio is present, but the tuner type tveeprom 2-0050: indicates otherwise. I will assume that radio is present. tveeprom 2-0050: Hauppauge model 25012, rev B168, serial# 8320352 tveeprom 2-0050: tuner model is LG TAPE H001F MK3 (idx 68, type 47) tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 2-0050: audio processor is CX25843 (idx 37) tveeprom 2-0050: decoder processor is CX25843 (idx 30) tveeprom 2-0050: has radio, has no IR remote tuner 2-0043: chip found @ 0x86 (ivtv i2c driver #0) tda9887 2-0043: tda988[5/6/7] found @ 0x43 (tuner) tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #0) cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0) cx25840 2-0044: loaded v4l-cx25840.fw firmware (16382 bytes) wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #0) ivtv0: Encoder revision: 0x02050032 ivtv0: Registered device video0 for encoder MPEG ivtv0: Registered device video32 for encoder YUV ivtv0: Registered device vbi0 for encoder VBI ivtv0: Registered device video24 for encoder PCM audio ivtv0: Registered device radio0 for encoder radio tuner 2-0061: type set to 47 (LG NTSC (TAPE series)) ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20 GSI 20 sharing vector 0xD1 and IRQ 20 ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [APCL] -> GSI 20 (level, low) -> IRQ 209 PCI: Setting latency timer of device 0000:00:0b.1 to 64 ehci_hcd 0000:00:0b.1: EHCI Host Controller ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0b.1: debug port 1 PCI: cache line size of 64 is not supported by device 0000:00:0b.1 ehci_hcd 0000:00:0b.1: irq 209, io mem 0xfe02e000 ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 177 PCI: Setting latency timer of device 0000:00:0b.0 to 64 ohci_hcd 0000:00:0b.0: OHCI Host Controller ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:0b.0: irq 177, io mem 0xfe02f000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 8 ports detected md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver nvidia: module license 'NVIDIA' taints kernel. ACPI: PCI Interrupt Link [APC7] enabled at IRQ 16 GSI 21 sharing vector 0xD9 and IRQ 21 ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APC7] -> GSI 16 (level, low) -> IRQ 217 PCI: Setting latency timer of device 0000:00:05.0 to 64 NVRM: loading NVIDIA Linux x86_64 Kernel Module 1.0-8776 Mon Oct 16 21:53:43 PDT 2006 ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ACPI: Sleep Button (CM) [SLPB] EXT3 FS on hda1, internal journal device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: [EMAIL PROTECTED] kjournald starting. Commit interval 5 seconds EXT3 FS on hda4, internal journal EXT3-fs: mounted filesystem with ordered data mode. Adding 2048276k swap on /dev/hda3. Priority:-1 extents:1 across:2048276k hald[3158]: segfault at 00007fff30d84000 rip 0000003c537708fa rsp 00007fff30d82668 error 6 eth0: no IPv6 routers present lirc_dev: disagrees about version of symbol struct_module lirc_serial: disagrees about version of symbol struct_module ACPI: PCI interrupt for device 0000:04:06.0 disabled ivtv0: Removed Hauppauge WinTV PVR-150, card #0 Linux video capture interface: v2.00 ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.8.0 (tagged release) loading ivtv: Linux version: 2.6.18.1 mod_unload gcc-3.4 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) PCI: Enabling device 0000:04:06.0 (0000 -> 0002) ACPI: PCI Interrupt 0000:04:06.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 201 ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) tuner 2-0043: chip found @ 0x86 (ivtv i2c driver #0) tda9887 2-0043: tda988[5/6/7] found @ 0x43 (tuner) tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #0) cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0) cx25840 2-0044: loaded v4l-cx25840.fw firmware (16382 bytes) wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #0) tveeprom 2-0050: The eeprom says no radio is present, but the tuner type tveeprom 2-0050: indicates otherwise. I will assume that radio is present. tveeprom 2-0050: Hauppauge model 25012, rev B168, serial# 8320352 tveeprom 2-0050: tuner model is LG TAPE H001F MK3 (idx 68, type 47) tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 2-0050: audio processor is CX25843 (idx 37) tveeprom 2-0050: decoder processor is CX25843 (idx 30) tveeprom 2-0050: has radio, has no IR remote ivtv0: Encoder revision: 0x02050032 ivtv0: Registered device video0 for encoder MPEG ivtv0: Registered device video32 for encoder YUV ivtv0: Registered device vbi0 for encoder VBI ivtv0: Registered device video24 for encoder PCM audio ivtv0: Registered device radio0 for encoder radio tuner 2-0061: type set to 47 (LG NTSC (TAPE series)) ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
