Try as I may, I cannot get anything but "i2c addr 0x44 not found
for command 0xc0cc5605!" when I try to capture anything with my new
Hauppauge PVR-150 (MCE).
I am running a brand new compile of 2.6.18.3 on a slackware 10.2
system. All the Video Adapters are set to modules in Device Drivers,
Multimedia Devices, Video Capture Adapters. Along with this, I am
running ivtv 0.8.1.
I tried to follow the HotTo on the ivtvdriver.org site, but
found the instructions to be slightly dated. Even so, I tried to follow
them and the resulting dmesg (after modprobe ivtv) is as follows:
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.8.1 (tagged release) loading
ivtv: Linux version: 2.6.18.3 mod_unload K7 REGPARM gcc-3.3
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge card (cx23416 based)
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
tveeprom 6-0050: Hauppauge model 26582, rev F0B2, serial# 10076677
tveeprom 6-0050: tuner model is TCL M2523_5N_E (idx 112, type 50)
tveeprom 6-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 6-0050: audio processor is CX25843 (idx 37)
tveeprom 6-0050: decoder processor is CX25843 (idx 30)
tveeprom 6-0050: has no radio, has no IR remote
ivtv0: Autodetected Hauppauge WinTV PVR-150
tuner 6-0061: chip found @ 0xc2 (ivtv i2c driver #0)
ivtv0: Encoder revision: 0x02050032
ivtv0: Registered device video0 for encoder MPEG
ivtv0: Registered device video32 for encoder YUV
ivtv0: Registered device vbi0 for encoder VBI
ivtv0: Registered device video24 for encoder PCM audio
tuner 6-0061: type set to 50 (TCL 2002N)
ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c!
ivtv0: i2c addr 0x44 not found for command 0x4008646f!
ivtv0: i2c hardware 0x00000020 (wm8775) not found for command 0x4008646d!
ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0x4008646d!
ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c!
ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
ivtv: ==================== END INIT IVTV ====================
After changing my I2C to a module in my kernel config, lsmod
reveals:
Module Size Used by
tuner 62184 0
ivtv 178448 0
cx2341x 9796 1 ivtv
tveeprom 13712 1 ivtv
videodev 22528 1 ivtv
v4l1_compat 12484 2 ivtv,videodev
v4l2_common 20416 4 tuner,ivtv,cx2341x,videodev
i2c_nforce2 5952 0
I spent 8 hours yesterday reading mailing list archives and
searching the net for anything that might help, and found that perhaps
this error has to do with the v4l drivers built into the kernel? Oh, I
don't know, please help :)
Greatly Appreciated.
j
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
