I had a running MythTV installation with a PVR-350 that I added a PVR-150 to (with ivtv-0.7.2). At first, I would get an unknown type error until I added the line
options ivtv1 tuner=50 in modprobe.conf The system would boot fine as long as nothing was plugged into either card (coaxial cables, output A/V cables, etc). As soon as I plugged everything into the PVR-350, the process freezes and I can't even get a console. The output that originally looked like: ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.7.2 (tagged release) loading ivtv: Linux version: 2.6.17-chw-8 SMP preempt mod_unload 586 gcc-3.4 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge WinTV PVR-350 card (cx23415 based) ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 tveeprom 1-0050: Hauppauge model 48132, rev K268, serial# 8551286 tveeprom 1-0050: tuner model is LG TAPE H001F MK3 (idx 68, type 47) tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 1-0050: audio processor is MSP4448 (idx 27) tveeprom 1-0050: decoder processor is SAA7115 (idx 19) tveeprom 1-0050: has radio, has IR remote tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) tda9887 1-0043: chip found @ 0x86 (ivtv i2c driver #0) saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) saa7127 1-0044: saa7129 found @ 0x88 (ivtv i2c driver #0) msp3400 1-0040: MSP4448G-B3 found @ 0x80 (ivtv i2c driver #0) msp3400 1-0040: MSP4448G-B3 supports radio, mode is autodetect and autoselect eth0: no IPv6 routers present ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02050032 ivtv0: Decoder revision: 0x02020023 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv0: Create encoder radio stream ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total) ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total) ivtv0: Create decoder VOUT stream ivtv0: Allocate DMA decoder YUV stream: 24 x 43200 buffers (1024KB total) ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes) tuner 1-0061: type set to 47 (LG NTSC (TAPE series)) ivtv0: Initialized Hauppauge WinTV PVR-350, card #0 ivtv: ====================== NEXT CARD ====================== ivtv1: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) ACPI: PCI Interrupt 0000:01:0d.0[A] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9 tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #1) tveeprom 2-0050: Hauppauge model 26582, rev F0B2, serial# 9411212 tveeprom 2-0050: tuner model is TCL M2523_5N_E (idx 112, type 4) tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 2-0050: audio processor is CX25843 (idx 37) tveeprom 2-0050: decoder processor is CX25843 (idx 30) tveeprom 2-0050: has no radio, has no IR remote cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1) cx25840 2-0044: loaded v4l-cx25840.fw firmware (16382 bytes) wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #1) ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv1: Encoder revision: 0x02050032 ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) tuner 2-0061: tuner type not set tuner 2-0061: tuner type not set ivtv1: Initialized Hauppauge WinTV PVR-150, card #1 ivtv: ==================== END INIT IVTV ==================== Now stops after the second line after ====NEXT CARD=== That is to say, I only see that ACPI: PCI Interrupt message and then everything is just frozen. I assume maybe it has to do with the PVR-350's decoder taking a spot that the PVR-150 was going to use? Can anyone shed some light? Thanks _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
