Hello, I have a problem with my pvr-350, I just do not get a picture. When I do "# cat /dev/video0 > /home/ch/test.mpg" it just gives me a zero byte file, as I'am doing it as root there should be no permission problems. (Mythtv does not work for the same reason) The card itself should be ok, it works in the same pc under windows xp.
I'am using Gentoo with kernel-2.6.19-gentoo-r5 and ivtv 0.10.0 (using the ebuild which was posted on this list) but I had the same problem with 0.91. dmesg looks pretty good, at least to me: ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.10.0 (tagged release) loading ivtv: Linux version: 2.6.19-gentoo-r5 SMP mod_unload PENTIUMIII REGPARM ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge card (cx23415 based) ACPI: PCI Interrupt 0000:04:03.0[A] -> GSI 17 (level, low) -> IRQ 24 ivtv0: Unreasonably low latency timer, setting to 64 (was 32) ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02060039 ivtv0: Decoder revision: 0x02020023 input: i2c IR (Hauppauge) as /class/input/input3 ir-kbd-i2c: i2c IR (Hauppauge) detected at i2c-0/0-0018/ir0 [ivtv i2c driver #0] saa7127 0-0044: saa7129 found @ 0x88 (ivtv i2c driver #0) msp3400 0-0040: MSP4418G-B3 found @ 0x80 (ivtv i2c driver #0) msp3400 0-0040: MSP4418G-B3 supports nicam and radio, mode is autodetect and autoselect tuner 0-0043: chip found @ 0x86 (ivtv i2c driver #0) tda9887 0-0043: tda988[5/6/7] found @ 0x43 (tuner) tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) tveeprom 0-0050: Hauppauge model 48139, rev K257, serial# 7880803 tveeprom 0-0050: tuner model is Philips FM1216 ME MK3 (idx 57, type 38) tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x74) tveeprom 0-0050: audio processor is MSP4418 (idx 25) tveeprom 0-0050: decoder processor is SAA7115 (idx 19) tveeprom 0-0050: has radio, has IR remote ivtv0: Autodetected Hauppauge WinTV PVR-350 ivtv0: Registered device video0 for encoder MPEG (4 MB) ivtv0: Registered device video32 for encoder YUV (2 MB) ivtv0: Registered device vbi0 for encoder VBI (1 MB) ivtv0: Registered device video24 for encoder PCM audio (1 MB) ivtv0: Registered device radio0 for encoder radio ivtv0: Registered device video16 for decoder MPEG (1 MB) ivtv0: Registered device vbi8 for decoder VBI (1 MB) ivtv0: Registered device vbi16 for decoder VOUT ivtv0: Registered device video48 for decoder YUV (1 MB) ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes) tuner 0-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) ivtv0: Initialized Hauppauge WinTV PVR-350, card #0 ivtv: ==================== END INIT IVTV ==================== Has somebody an idea what I did wrong? or what I could test? Greets Christoph _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
