2007/2/21, Sander Sweers <[EMAIL PROTECTED]>: > Not to me ;-) I dont see the saa7115 module loading. Do you have this > enabled in your kernel? Check the .config file for CONFIG_VIDEO_SAA711X.
It is enabled: CONFIG_VIDEO_SAA711X=y Greets Christoph > > ivtv: ==================== START INIT IVTV ==================== > > ivtv: version 0.10.0 (tagged release) loading > > ivtv: Linux version: 2.6.19-gentoo-r5 SMP mod_unload PENTIUMIII REGPARM > > ivtv: In case of problems please include the debug info between > > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > > ivtv: any module options, when mailing the ivtv-users mailinglist. > > ivtv0: Autodetected Hauppauge card (cx23415 based) > > ACPI: PCI Interrupt 0000:04:03.0[A] -> GSI 17 (level, low) -> IRQ 24 > > ivtv0: Unreasonably low latency timer, setting to 64 (was 32) > > ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) > > ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) > > ivtv0: Encoder revision: 0x02060039 > > ivtv0: Decoder revision: 0x02020023 > > input: i2c IR (Hauppauge) as /class/input/input3 > > ir-kbd-i2c: i2c IR (Hauppauge) detected at i2c-0/0-0018/ir0 [ivtv i2c > > driver #0] > > saa7127 0-0044: saa7129 found @ 0x88 (ivtv i2c driver #0) > > msp3400 0-0040: MSP4418G-B3 found @ 0x80 (ivtv i2c driver #0) > > msp3400 0-0040: MSP4418G-B3 supports nicam and radio, mode is > > autodetect and autoselect > > tuner 0-0043: chip found @ 0x86 (ivtv i2c driver #0) > > tda9887 0-0043: tda988[5/6/7] found @ 0x43 (tuner) > > tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) > > tveeprom 0-0050: Hauppauge model 48139, rev K257, serial# 7880803 > > tveeprom 0-0050: tuner model is Philips FM1216 ME MK3 (idx 57, type 38) > > tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) > > (eeprom 0x74) > > tveeprom 0-0050: audio processor is MSP4418 (idx 25) > > tveeprom 0-0050: decoder processor is SAA7115 (idx 19) > > tveeprom 0-0050: has radio, has IR remote > > ivtv0: Autodetected Hauppauge WinTV PVR-350 > > ivtv0: Registered device video0 for encoder MPEG (4 MB) > > ivtv0: Registered device video32 for encoder YUV (2 MB) > > ivtv0: Registered device vbi0 for encoder VBI (1 MB) > > ivtv0: Registered device video24 for encoder PCM audio (1 MB) > > ivtv0: Registered device radio0 for encoder radio > > ivtv0: Registered device video16 for decoder MPEG (1 MB) > > ivtv0: Registered device vbi8 for decoder VBI (1 MB) > > ivtv0: Registered device vbi16 for decoder VOUT > > ivtv0: Registered device video48 for decoder YUV (1 MB) > > ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes) > > tuner 0-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) > > ivtv0: Initialized Hauppauge WinTV PVR-350, card #0 > > ivtv: ==================== END INIT IVTV ==================== > > > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users > _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
