Hi, ivtv0: unable to open firmware v4l-cx2341x-init.mpg (must be 155648 bytes) > You should find the new v4l-cx2341x-init.mpg in the latest ivtv release from Hans Verkuil and copy that to the appropriate directory Good luck Roger On Fri, 2007-03-02 at 01:49 -0500, Fred Firestine wrote: > Hi all, > > I have been a MythTV fanatic since I first built my Fedora Core 4 > system with a PVR-350 card using Jarod Wilson's instructions some > months ago. Later I added a PVR-150 card, which was a bit tricky > because I couldn't get the two cards to be recording at the same time > (it seems the second would never start). Eventually I figured out the > solution to this problem using the "tuner=" ivtv option in > modprobe.conf (see below) and/or by powering off the system when > necessary rather than just rebooting. I was happy, everything was > running great, until I got the idea to upgrade (fresh install, > actually) Fedora Core 6. Now I can't get the second card to record > (again!), even after a shutdown and poweroff, and I can hear sound > when I play recordings in MythTV but I can only see a black box. I > have found what I hoped was a solution for the "no video" problem (see > modprobe.conf) but it doesn't seem to work for me. Any help would be > appreciated, as I have been trying to recover for a week now and I am > kicking myself for breaking a working system in order to upgrade! If > not for me, please help my wife and young children. ;-) > > One thing I did notice but I am not sure how to correct: I have a > framebuffer /dev/fb0, and /dev/fb linked to it, but no /dev/fb1 for > the second card. Is that OK? I can't remember anymore from my previous > setup. > > Thanks in advance, > > Fred > > > Kernel version: 2.6.19-1.2911.fc6 (Fedora Core 6) > > MythTV version: 0.20-153.fc6.at > > IVTV RPMs installed: > > ivtv-kmdl-2.6.19-1.2911.fc6-0.10.0-125.fc6.at > ivtv-firmware-1.8a-13.at > ivtv_xdriver-0.10.7-8_r3843.fc6.at > perl-Video-ivtv-0.13-8.fc6.at > ivtv-0.10.0-125.fc6.at > > ivtv: ==================== START INIT IVTV ==================== > > ivtv: version 0.10.0 (tagged release) loading > > ivtv: Linux version: 2.6.19-1.2911.fc6 SMP mod_unload 686 REGPARM 4KSTACKS > > ivtv: In case of problems please include the debug info between > > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > > ivtv: any module options, when mailing the ivtv-users mailinglist. > > ivtv0: Autodetected Hauppauge card (cx23415 based) > > ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 7 > > PCI: setting IRQ 7 as level-triggered > > ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [LNKA] -> GSI 7 (level, > low) -> IRQ 7 > > ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) > > ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) > > ivtv0: Encoder revision: 0x02060039 > > ivtv0: Decoder revision: 0x02020023 > > msp3400 0-0040: MSP4448G-A2 found @ 0x80 (ivtv i2c driver #0) > > msp3400 0-0040: MSP4448G-A2 supports radio, mode is autodetect and autoselect > > i2c_adapter i2c-0: Client creation failed at 0x44 (-1) > > saa7115 0-0021: saa7115 found (1f7115d0e100000) @ 0x42 (ivtv i2c driver #0) > > tuner 0-0043: chip found @ 0x86 (ivtv i2c driver #0) > > tda9887 0-0043: tda988[5/6/7] found @ 0x43 (tuner) > > tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) > > saa7127 0-0044: saa7129 found @ 0x88 (ivtv i2c driver #0) > > tveeprom 0-0050: Hauppauge model 48132, rev K268, serial# 8500007 > > tveeprom 0-0050: tuner model is LG TAPE H001F MK3 (idx 68, type 47) > > tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08) > > tveeprom 0-0050: audio processor is MSP4448 (idx 27) > > tveeprom 0-0050: decoder processor is SAA7115 (idx 19) > > tveeprom 0-0050: has radio, has IR remote > > ivtv0: Autodetected Hauppauge WinTV PVR-350 > > ivtv0: Registered device video0 for encoder MPEG (4 MB) > > ivtv0: Registered device video32 for encoder YUV (2 MB) > > ivtv0: Registered device vbi0 for encoder VBI (1 MB) > > ivtv0: Registered device video24 for encoder PCM audio (1 MB) > > ivtv0: Registered device radio0 for encoder radio > > ivtv0: Registered device video16 for decoder MPEG (1 MB) > > ivtv0: Registered device vbi8 for decoder VBI (1 MB) > > ivtv0: Registered device vbi16 for decoder VOUT > > ivtv0: Registered device video48 for decoder YUV (1 MB) > > ivtv0: unable to open firmware v4l-cx2341x-init.mpg (must be 155648 bytes) > > ivtv0: did you put the firmware in the hotplug firmware directory? > > ivtv0: failed to read mpeg decoder initialisation file v4l-cx2341x-init.mpg > > tuner 0-0061: type set to 47 (LG NTSC (TAPE series)) > > ivtv0: Initialized Hauppauge WinTV PVR-350, card #0 > > ivtv: ====================== NEXT CARD ====================== > > ivtv1: Autodetected Hauppauge card (cx23416 based) > > ACPI: PCI Interrupt 0000:02:0b.0[A] -> Link [LNKA] -> GSI 7 (level, > low) -> IRQ 7 > > ivtv1: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) > > ivtv1: Encoder revision: 0x02060039 > > i2c_adapter i2c-1: Client creation failed at 0x44 (-1) > > tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #1) > > tveeprom 1-0050: Hauppauge model 26132, rev G1B2, serial# 9519117 > > tveeprom 1-0050: tuner model is TCL M2523_5N_E (idx 112, type 50) > > tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08) > > tveeprom 1-0050: audio processor is CX25841 (idx 35) > > tveeprom 1-0050: decoder processor is CX25841 (idx 28) > > tveeprom 1-0050: has no radio, has IR remote > > ivtv1: Autodetected Hauppauge WinTV PVR-150 > > ivtv1: reopen i2c bus for IR-blaster support > > i2c_adapter i2c-1: Client creation failed at 0x44 (-1) > > tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #1) > > ivtv1: Registered device video1 for encoder MPEG (4 MB) > > ivtv1: Registered device video33 for encoder YUV (2 MB) > > ivtv1: Registered device vbi1 for encoder VBI (1 MB) > > ivtv1: Registered device video25 for encoder PCM audio (1 MB) > > tuner 1-0061: type set to 50 (TCL 2002N) > > ivtv1: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! > > ivtv1: i2c addr 0x44 not found for command 0x4008646f! > > ivtv1: i2c hardware 0x00000020 (wm8775) not found for command 0x4008646d! > > ivtv1: i2c hardware 0x00000001 (cx2584x) not found for command 0x4008646d! > > ivtv1: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! > > ivtv1: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! > > ivtv1: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! > > ivtv1: Initialized Hauppauge WinTV PVR-150, card #1 > > ivtv: ==================== END INIT IVTV ==================== > > modprobe.conf (no errors reported by "depmode -a; modprobe ivtv"): > > # ivtv modules setup > # I thought this was working in Fedora Core 4 to get both cards' IDs > options ivtv tuner=-1,50 > # this was suggested to fix the "black screen" problem with PVR-350 TV-OUT > options ivtv-fb osd_compat=1 > alias char-major-81 videodev > alias char-major-81-0 ivtv > alias char-major-81-1 ivtv > install ivtv /sbin/modprobe --ignore-install ivtv; /sbin/modprobe ivtv-fb > # ivtv end > > ======================================================= > > Text from /var/log/messages during non-recording by second card, and > playback problem: > > Mar 2 01:14:38 mythtv kernel: ivtv1: i2c hardware 0x00000001 > (cx2584x) not found for command 0xc008561c! > Mar 2 01:14:38 mythtv kernel: ivtv1: i2c hardware 0x00000001 > (cx2584x) not found for command 0xc008561c! > Mar 2 01:14:38 mythtv kernel: ivtv1: i2c addr 0x44 not found for > command 0xc0445624! > Mar 2 01:14:38 mythtv kernel: ivtv1: i2c addr 0x44 not found for > command 0xc008561c! > Mar 2 01:14:38 mythtv kernel: ivtv1: i2c addr 0x44 not found for > command 0xc0cc5605! > Mar 2 01:14:38 mythtv kernel: ivtv1: i2c hardware 0x00000001 > (cx2584x) not found for command 0xc008561c! > Mar 2 01:14:38 mythtv kernel: ivtv1: i2c addr 0x44 not found for > command 0xc0cc5605! > Mar 2 01:14:38 mythtv kernel: ivtv1 warning: > CX2341X_ENC_SET_VBI_CONFIG took 113 jiffies (1000 per HZ) > Mar 2 01:14:44 mythtv kernel: ivtv1: i2c addr 0x44 not found for > command 0xc0cc5605! > Mar 2 01:15:01 mythtv last message repeated 3 times > Mar 2 01:15:29 mythtv kernel: ivtv0-fb warning: > IVTVFB_IOCTL_GET_FRAME_BUFFER no longer supported > Mar 2 01:15:29 mythtv kernel: ivtv0-fb warning: - Please use > FBIOGET_VSCREENINFO & FBIOGET_FSCREENINFO > Mar 2 01:15:29 mythtv kernel: ivtv0-fb warning: > IVTVFB_IOCTL_GET_ACTIVE_BUFFER no longer supported > Mar 2 01:15:29 mythtv kernel: ivtv0-fb warning: - Please use > FBIOGET_VSCREENINFO > Mar 2 01:15:29 mythtv kernel: ivtv0-fb warning: ivtv_fb_prep_frame: > Nothing to do. count = 0 > Mar 2 01:15:29 mythtv kernel: ivtv0-fb warning: > IVTVFB_IOCTL_SET_ACTIVE_BUFFER no longer supported > Mar 2 01:15:29 mythtv kernel: ivtv0-fb warning: - Please use > FBIOPUT_VSCREENINFO > Mar 2 01:15:29 mythtv kernel: > Mar 2 01:15:35 mythtv kernel: ivtv0-fb warning: ivtv_fb_prep_frame: > Nothing to do. count = 0 > Mar 2 01:15:35 mythtv last message repeated 3 times > Mar 2 01:15:35 mythtv kernel: ivtv0: Stereo mode changed > Mar 2 01:15:35 mythtv kernel: ivtv0-fb warning: ivtv_fb_prep_frame: > Nothing to do. count = 0 > Mar 2 01:15:42 mythtv last message repeated 209 times > Mar 2 01:15:43 mythtv kernel: ivtv0-fb warning: > IVTVFB_IOCTL_GET_ACTIVE_BUFFER no longer supported > Mar 2 01:15:43 mythtv kernel: ivtv0-fb warning: - Please use > FBIOGET_VSCREENINFO > Mar 2 01:15:43 mythtv kernel: ivtv0-fb warning: ivtv_fb_prep_frame: > Nothing to do. count = 0 > > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users
_______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
