Roger, Thanks for your quick reply. As part of Jarod's instructions, I have run the commands
# yum -y install ivtv-firmware # yum -y install ivtv-kmdl-$KVER And these seem to have been successful, since /lib/modules contains [EMAIL PROTECTED] ~]# ls -l /lib/modules total 168 drwxr-xr-x 6 root root 4096 Feb 26 20:30 2.6.18-1.2798.fc6 drwxr-xr-x 7 root root 4096 Mar 2 00:58 2.6.19-1.2911.fc6 lrwxrwxrwx 1 root root 28 Feb 27 11:24 HcwMakoA.ROM -> /lib/firmware/v4l-cx25840.fw lrwxrwxrwx 1 root root 32 Feb 27 11:24 ivtv-fw-dec.bin -> /lib/firmware/v4l-cx2341x-dec.fw lrwxrwxrwx 1 root root 32 Feb 27 11:24 ivtv-fw-enc.bin -> /lib/firmware/v4l-cx2341x-enc.fw lrwxrwxrwx 1 root root 32 Feb 27 11:24 v4l-cx2341x-dec.fw -> /lib/firmware/v4l-cx2341x-dec.fw lrwxrwxrwx 1 root root 32 Feb 27 11:24 v4l-cx2341x-enc.fw -> /lib/firmware/v4l-cx2341x-enc.fw -rwxr-xr-x 1 root root 155648 Dec 29 2005 v4l-cx2341x-init.mpg lrwxrwxrwx 1 root root 28 Feb 27 11:24 v4l-cx25840.fw -> /lib/firmware/v4l-cx25840.fw [EMAIL PROTECTED] ~]# Is there a configuration step for Fedora which I missed or did not complete properly? I am looking at the files in /etc/udev/rules.d, just a guess based on the hotplug info I am reading, but I have no idea what to look at or fix. Fred On 3/2/07, Roger Depreeuw <[EMAIL PROTECTED]> wrote: > Hi, > ivtv0: unable to open firmware v4l-cx2341x-init.mpg (must be 155648 > bytes) > > > You should find the new v4l-cx2341x-init.mpg in the latest ivtv release > from Hans Verkuil and copy that to the appropriate directory > Good luck > Roger > On Fri, 2007-03-02 at 01:49 -0500, Fred Firestine wrote: > > Hi all, > > > > I have been a MythTV fanatic since I first built my Fedora Core 4 > > system with a PVR-350 card using Jarod Wilson's instructions some > > months ago. Later I added a PVR-150 card, which was a bit tricky > > because I couldn't get the two cards to be recording at the same time > > (it seems the second would never start). Eventually I figured out the > > solution to this problem using the "tuner=" ivtv option in > > modprobe.conf (see below) and/or by powering off the system when > > necessary rather than just rebooting. I was happy, everything was > > running great, until I got the idea to upgrade (fresh install, > > actually) Fedora Core 6. Now I can't get the second card to record > > (again!), even after a shutdown and poweroff, and I can hear sound > > when I play recordings in MythTV but I can only see a black box. I > > have found what I hoped was a solution for the "no video" problem (see > > modprobe.conf) but it doesn't seem to work for me. Any help would be > > appreciated, as I have been trying to recover for a week now and I am > > kicking myself for breaking a working system in order to upgrade! If > > not for me, please help my wife and young children. ;-) > > > > One thing I did notice but I am not sure how to correct: I have a > > framebuffer /dev/fb0, and /dev/fb linked to it, but no /dev/fb1 for > > the second card. Is that OK? I can't remember anymore from my previous > > setup. > > > > Thanks in advance, > > > > Fred > > > > > > Kernel version: 2.6.19-1.2911.fc6 (Fedora Core 6) > > > > MythTV version: 0.20-153.fc6.at > > > > IVTV RPMs installed: > > > > ivtv-kmdl-2.6.19-1.2911.fc6-0.10.0-125.fc6.at > > ivtv-firmware-1.8a-13.at > > ivtv_xdriver-0.10.7-8_r3843.fc6.at > > perl-Video-ivtv-0.13-8.fc6.at > > ivtv-0.10.0-125.fc6.at > > > > ivtv: ==================== START INIT IVTV ==================== > > > > ivtv: version 0.10.0 (tagged release) loading > > > > ivtv: Linux version: 2.6.19-1.2911.fc6 SMP mod_unload 686 REGPARM 4KSTACKS > > > > ivtv: In case of problems please include the debug info between > > > > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > > > > ivtv: any module options, when mailing the ivtv-users mailinglist. > > > > ivtv0: Autodetected Hauppauge card (cx23415 based) > > > > ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 7 > > > > PCI: setting IRQ 7 as level-triggered > > > > ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [LNKA] -> GSI 7 (level, > > low) -> IRQ 7 > > > > ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) > > > > ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) > > > > ivtv0: Encoder revision: 0x02060039 > > > > ivtv0: Decoder revision: 0x02020023 > > > > msp3400 0-0040: MSP4448G-A2 found @ 0x80 (ivtv i2c driver #0) > > > > msp3400 0-0040: MSP4448G-A2 supports radio, mode is autodetect and > > autoselect > > > > i2c_adapter i2c-0: Client creation failed at 0x44 (-1) > > > > saa7115 0-0021: saa7115 found (1f7115d0e100000) @ 0x42 (ivtv i2c driver #0) > > > > tuner 0-0043: chip found @ 0x86 (ivtv i2c driver #0) > > > > tda9887 0-0043: tda988[5/6/7] found @ 0x43 (tuner) > > > > tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) > > > > saa7127 0-0044: saa7129 found @ 0x88 (ivtv i2c driver #0) > > > > tveeprom 0-0050: Hauppauge model 48132, rev K268, serial# 8500007 > > > > tveeprom 0-0050: tuner model is LG TAPE H001F MK3 (idx 68, type 47) > > > > tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08) > > > > tveeprom 0-0050: audio processor is MSP4448 (idx 27) > > > > tveeprom 0-0050: decoder processor is SAA7115 (idx 19) > > > > tveeprom 0-0050: has radio, has IR remote > > > > ivtv0: Autodetected Hauppauge WinTV PVR-350 > > > > ivtv0: Registered device video0 for encoder MPEG (4 MB) > > > > ivtv0: Registered device video32 for encoder YUV (2 MB) > > > > ivtv0: Registered device vbi0 for encoder VBI (1 MB) > > > > ivtv0: Registered device video24 for encoder PCM audio (1 MB) > > > > ivtv0: Registered device radio0 for encoder radio > > > > ivtv0: Registered device video16 for decoder MPEG (1 MB) > > > > ivtv0: Registered device vbi8 for decoder VBI (1 MB) > > > > ivtv0: Registered device vbi16 for decoder VOUT > > > > ivtv0: Registered device video48 for decoder YUV (1 MB) > > > > ivtv0: unable to open firmware v4l-cx2341x-init.mpg (must be 155648 bytes) > > > > ivtv0: did you put the firmware in the hotplug firmware directory? > > > > ivtv0: failed to read mpeg decoder initialisation file v4l-cx2341x-init.mpg > > > > tuner 0-0061: type set to 47 (LG NTSC (TAPE series)) > > > > ivtv0: Initialized Hauppauge WinTV PVR-350, card #0 > > > > ivtv: ====================== NEXT CARD ====================== > > > > ivtv1: Autodetected Hauppauge card (cx23416 based) > > > > ACPI: PCI Interrupt 0000:02:0b.0[A] -> Link [LNKA] -> GSI 7 (level, > > low) -> IRQ 7 > > > > ivtv1: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) > > > > ivtv1: Encoder revision: 0x02060039 > > > > i2c_adapter i2c-1: Client creation failed at 0x44 (-1) > > > > tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #1) > > > > tveeprom 1-0050: Hauppauge model 26132, rev G1B2, serial# 9519117 > > > > tveeprom 1-0050: tuner model is TCL M2523_5N_E (idx 112, type 50) > > > > tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08) > > > > tveeprom 1-0050: audio processor is CX25841 (idx 35) > > > > tveeprom 1-0050: decoder processor is CX25841 (idx 28) > > > > tveeprom 1-0050: has no radio, has IR remote > > > > ivtv1: Autodetected Hauppauge WinTV PVR-150 > > > > ivtv1: reopen i2c bus for IR-blaster support > > > > i2c_adapter i2c-1: Client creation failed at 0x44 (-1) > > > > tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #1) > > > > ivtv1: Registered device video1 for encoder MPEG (4 MB) > > > > ivtv1: Registered device video33 for encoder YUV (2 MB) > > > > ivtv1: Registered device vbi1 for encoder VBI (1 MB) > > > > ivtv1: Registered device video25 for encoder PCM audio (1 MB) > > > > tuner 1-0061: type set to 50 (TCL 2002N) > > > > ivtv1: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! > > > > ivtv1: i2c addr 0x44 not found for command 0x4008646f! > > > > ivtv1: i2c hardware 0x00000020 (wm8775) not found for command 0x4008646d! > > > > ivtv1: i2c hardware 0x00000001 (cx2584x) not found for command 0x4008646d! > > > > ivtv1: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! > > > > ivtv1: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! > > > > ivtv1: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! > > > > ivtv1: Initialized Hauppauge WinTV PVR-150, card #1 > > > > ivtv: ==================== END INIT IVTV ==================== > > > > modprobe.conf (no errors reported by "depmode -a; modprobe ivtv"): > > > > # ivtv modules setup > > # I thought this was working in Fedora Core 4 to get both cards' IDs > > options ivtv tuner=-1,50 > > # this was suggested to fix the "black screen" problem with PVR-350 TV-OUT > > options ivtv-fb osd_compat=1 > > alias char-major-81 videodev > > alias char-major-81-0 ivtv > > alias char-major-81-1 ivtv > > install ivtv /sbin/modprobe --ignore-install ivtv; /sbin/modprobe ivtv-fb > > # ivtv end > > > > ======================================================= > > > > Text from /var/log/messages during non-recording by second card, and > > playback problem: > > > > Mar 2 01:14:38 mythtv kernel: ivtv1: i2c hardware 0x00000001 > > (cx2584x) not found for command 0xc008561c! > > Mar 2 01:14:38 mythtv kernel: ivtv1: i2c hardware 0x00000001 > > (cx2584x) not found for command 0xc008561c! > > Mar 2 01:14:38 mythtv kernel: ivtv1: i2c addr 0x44 not found for > > command 0xc0445624! > > Mar 2 01:14:38 mythtv kernel: ivtv1: i2c addr 0x44 not found for > > command 0xc008561c! > > Mar 2 01:14:38 mythtv kernel: ivtv1: i2c addr 0x44 not found for > > command 0xc0cc5605! > > Mar 2 01:14:38 mythtv kernel: ivtv1: i2c hardware 0x00000001 > > (cx2584x) not found for command 0xc008561c! > > Mar 2 01:14:38 mythtv kernel: ivtv1: i2c addr 0x44 not found for > > command 0xc0cc5605! > > Mar 2 01:14:38 mythtv kernel: ivtv1 warning: > > CX2341X_ENC_SET_VBI_CONFIG took 113 jiffies (1000 per HZ) > > Mar 2 01:14:44 mythtv kernel: ivtv1: i2c addr 0x44 not found for > > command 0xc0cc5605! > > Mar 2 01:15:01 mythtv last message repeated 3 times > > Mar 2 01:15:29 mythtv kernel: ivtv0-fb warning: > > IVTVFB_IOCTL_GET_FRAME_BUFFER no longer supported > > Mar 2 01:15:29 mythtv kernel: ivtv0-fb warning: - Please use > > FBIOGET_VSCREENINFO & FBIOGET_FSCREENINFO > > Mar 2 01:15:29 mythtv kernel: ivtv0-fb warning: > > IVTVFB_IOCTL_GET_ACTIVE_BUFFER no longer supported > > Mar 2 01:15:29 mythtv kernel: ivtv0-fb warning: - Please use > > FBIOGET_VSCREENINFO > > Mar 2 01:15:29 mythtv kernel: ivtv0-fb warning: ivtv_fb_prep_frame: > > Nothing to do. count = 0 > > Mar 2 01:15:29 mythtv kernel: ivtv0-fb warning: > > IVTVFB_IOCTL_SET_ACTIVE_BUFFER no longer supported > > Mar 2 01:15:29 mythtv kernel: ivtv0-fb warning: - Please use > > FBIOPUT_VSCREENINFO > > Mar 2 01:15:29 mythtv kernel: > > Mar 2 01:15:35 mythtv kernel: ivtv0-fb warning: ivtv_fb_prep_frame: > > Nothing to do. count = 0 > > Mar 2 01:15:35 mythtv last message repeated 3 times > > Mar 2 01:15:35 mythtv kernel: ivtv0: Stereo mode changed > > Mar 2 01:15:35 mythtv kernel: ivtv0-fb warning: ivtv_fb_prep_frame: > > Nothing to do. count = 0 > > Mar 2 01:15:42 mythtv last message repeated 209 times > > Mar 2 01:15:43 mythtv kernel: ivtv0-fb warning: > > IVTVFB_IOCTL_GET_ACTIVE_BUFFER no longer supported > > Mar 2 01:15:43 mythtv kernel: ivtv0-fb warning: - Please use > > FBIOGET_VSCREENINFO > > Mar 2 01:15:43 mythtv kernel: ivtv0-fb warning: ivtv_fb_prep_frame: > > Nothing to do. count = 0 > > > > _______________________________________________ > > ivtv-users mailing list > > [email protected] > > http://ivtvdriver.org/mailman/listinfo/ivtv-users > > > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users > _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
