Hello list Having just updated from the atrpms packaged version of ivtv 0.10.0 to ivtv 0.10.1 and the output on my pvr350 has become what I can only describe as a streaky diagonal mess (although the output is still just about recognisable as for instance my x session or whatever I am trying to play). Before the ivtv-fb module loads I have a black screen with a few very thin diagonal blue flickering lines and with the saa7127 test image is also distorted in this flickering diagonal manner.
Strangely downgrading back to 0.10.0 which was working absolutely perfectly until I attempt the upgrade changes nothing so my upgrade attempt must have updated something but I cant figure out what.... I think I am using the correct firmware versions (see below) and I am not specifying any module options. I know this is not a hardware/cabling as I still have a 2.6.18 kernel with ivtv 0.8 which still works fine if I boot with this kernel. any help working out why output on my pvr350 on 0.10.0 or 0.10.1 has broken would be greatly greatly appreciated! many thanks in advance Jerome ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.10.1 (tagged release) loading ivtv: Linux version: 2.6.19-1.2911.6.4.fc6 SMP mod_unload 686 REGPARM 4KSTACKS ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge card (cx23415 based) ACPI: PCI Interrupt 0000:01:09.0[A] -> GSI 17 (level, low) -> IRQ 20 ivtv0: Unreasonably low latency timer, setting to 64 (was 32) dvb-usb: found a 'Hauppauge WinTV-NOVA-T usb2' in warm state. dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. DVB: registering new adapter (Hauppauge WinTV-NOVA-T usb2). dvb-usb: MAC address: 00:0d:fe:02:cd:e2 DVB: registering frontend 0 (DiBcom 3000MC/P)... input: IR-receiver inside an USB DVB receiver as /class/input/input2 dvb-usb: schedule remote query interval to 100 msecs. dvb-usb: Hauppauge WinTV-NOVA-T usb2 successfully initialized and connected. sd 0:0:0:0: Attached scsi generic sg0 type 0 zd1211rw 5-5:1.0: firmware version 4605 zd1211rw 5-5:1.0: zd1211 chip 07b8:6001 v4330 high 00-12-0e AL2230_RF pa0 g--- zd1211rw 5-5:1.0: eth1 usbcore: registered new interface driver dvb_usb_nova_t_usb2 usbcore: registered new interface driver zd1211rw ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) ieee1394: Host added: ID:BUS[0-00:1023] GUID[00301bb5000099fa] ivtv0: Encoder revision: 0x02060039 ivtv0: Decoder revision: 0x02020023 saa7127 3-0044: saa7127 found @ 0x88 (ivtv i2c driver #0) tveeprom 3-0050: Hauppauge model 48135, rev J324, serial# 7244587 tveeprom 3-0050: tuner model is Philips FM1246 (idx 24, type 1) tveeprom 3-0050: TV standards PAL(I) (eeprom 0x10) tveeprom 3-0050: audio processor is MSP4418 (idx 25) tveeprom 3-0050: decoder processor is SAA7115 (idx 19) tveeprom 3-0050: has radio, has IR receiver, has no IR transmitter ivtv0: Autodetected Hauppauge WinTV PVR-350 tuner 3-0061: chip found @ 0xc2 (ivtv i2c driver #0) i2c_adapter i2c-1: SMBus Quick command not supported, can't probe for chips i2c_adapter i2c-2: SMBus Quick command not supported, can't probe for chips saa7115 3-0021: saa7115 found (1f7115d0e100000) @ 0x42 (ivtv i2c driver #0) msp3400 3-0040: MSP4418G-A2 found @ 0x80 (ivtv i2c driver #0) msp3400 3-0040: MSP4418G-A2 supports nicam and radio, mode is autodetect and autoselect ivtv0: Registered device video0 for encoder MPEG (4 MB) ivtv0: Registered device video32 for encoder YUV (2 MB) ivtv0: Registered device vbi0 for encoder VBI (1 MB) ivtv0: Registered device video24 for encoder PCM audio (1 MB) ivtv0: Registered device radio0 for encoder radio ivtv0: Registered device video16 for decoder MPEG (1 MB) ivtv0: Registered device vbi8 for decoder VBI (1 MB) ivtv0: Registered device vbi16 for decoder VOUT ivtv0: Registered device video48 for decoder YUV (1 MB) ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes) tuner 3-0061: type set to 1 (Philips PAL_I (FI1246 and compatibles)) ivtv0: Initialized Hauppauge WinTV PVR-350, card #0 ivtv: ==================== END INIT IVTV ==================== _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
