Hello! I am using a PVR-350 on Gentoo Linux (Kernel 2.6.20-gentoo-r6) with ivtv 0.10.1.
When I load the ivtv-fb module I get the following lines in /var/log/messages: May 4 20:22:50 tv ivtv0-fb: === Validated display mode === May 4 20:22:50 tv ivtv0-fb: Display size 640x480 (640x480 Virtual) @ 32bpp May 4 20:22:50 tv ivtv0-fb: Display position 41,49 May 4 20:22:50 tv ivtv0-fb: Display filter : on May 4 20:22:50 tv ivtv0-fb: Color space : RGB May 4 20:22:50 tv ivtv0-fb: === Display mode change === May 4 20:22:50 tv ivtv0-fb: Display size 640x480 (640x480 Virtual) @ 32bpp May 4 20:22:50 tv ivtv0-fb: Display position 41,49 May 4 20:22:50 tv ivtv0-fb: Display filter : on May 4 20:22:50 tv ivtv0-fb: Color space : RGB May 4 20:23:17 tv ivtv0-fb: === Validated display mode === May 4 20:23:17 tv ivtv0-fb: Display size 640x480 (640x480 Virtual) @ 8bpp May 4 20:23:17 tv ivtv0-fb: Display position 41,49 May 4 20:23:17 tv ivtv0-fb: Display filter : on May 4 20:23:17 tv ivtv0-fb: Color space : RGB May 4 20:23:17 tv ivtv0-fb: === Display mode change === May 4 20:23:17 tv ivtv0-fb: Display size 640x480 (640x480 Virtual) @ 8bpp May 4 20:23:17 tv ivtv0-fb: Display position 41,49 May 4 20:23:17 tv ivtv0-fb: Display filter : on May 4 20:23:17 tv ivtv0-fb: Color space : RGB And the resolution is indeed 640x480. However, I want a resolution of 720x576 (PAL). I played around with ivtvfbctl, but that command has no effect as far as I can tell?! Thanks in advance! Regards, georg P.S.: ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.10.1 (tagged release) loading ivtv: Linux version: 2.6.18-gentoo-r6_gk-27042007 preempt mod_unload K7 REGPARM gcc-4.1 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge card (cx23415 based) PCI: Enabling device 0000:00:0b.0 (0014 -> 0016) ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 19 (level, low) -> IRQ 19 ivtv0: Unreasonably low latency timer, setting to 64 (was 32) ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02060039 ivtv0: Decoder revision: 0x02020023 tveeprom 1-0050: Hauppauge model 48139, rev K257, serial# 8577574 tveeprom 1-0050: tuner model is Philips FM1216 ME MK3 (idx 57, type 38) tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x74) tveeprom 1-0050: audio processor is MSP4418 (idx 25) tveeprom 1-0050: decoder processor is SAA7115 (idx 19) tveeprom 1-0050: has radio, has IR remote ivtv0: Autodetected Hauppauge WinTV PVR-350 tuner 1-0043: chip found @ 0x86 (ivtv i2c driver #0) tda9887 1-0043: tda988[5/6/7] found @ 0x43 (tuner) tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) saa7127 1-0044: saa7129 found @ 0x88 (ivtv i2c driver #0) msp3400 1-0040: MSP4418G-B3 found @ 0x80 (ivtv i2c driver #0) msp3400 1-0040: MSP4418G-B3 supports nicam and radio, mode is autodetect and autoselect ivtv0: Registered device video0 for encoder MPEG (4 MB) ivtv0: Registered device video32 for encoder YUV (2 MB) ivtv0: Registered device vbi0 for encoder VBI (1 MB) ivtv0: Registered device video24 for encoder PCM audio (1 MB) ivtv0: Registered device radio0 for encoder radio ivtv0: Registered device video16 for decoder MPEG (1 MB) ivtv0: Registered device vbi8 for decoder VBI (1 MB) ivtv0: Registered device vbi16 for decoder VOUT ivtv0: Registered device video48 for decoder YUV (1 MB) ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes) tuner 1-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) ivtv0: Initialized Hauppauge WinTV PVR-350, card #0 ivtv: ==================== END INIT IVTV ==================== _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
