Hi, My problems still exist with no video or audio after including missing module into kernel. After v4l2-ctl --log-status command I've got this:
Status Log: ivtv0: ================= START STATUS CARD #0 ================= saa7115 4-0021: Audio frequency: 48000 Hz saa7115 4-0021: Input: Composite 3 saa7115 4-0021: Video signal: bad saa7115 4-0021: Frequency: 50 Hz saa7115 4-0021: Detected format: BW/No color saa7115 4-0021: Width, Height: 720, 480 cs53l32a 4-0011: Input: 2 cs53l32a 4-0011: Volume: 0 dB ivtv0: Video Input: Composite 1 ivtv0: Audio Input: Line In 1 ivtv0: Tuner: TV ivtv0: Stream: MPEG-2 Program Stream ivtv0: VBI Format: No VBI ivtv0: Video: 720x480, 30 fps ivtv0: Video: MPEG-2, 4x3, Variable Bitrate, 6000000, Peak 8000000 ivtv0: Video: GOP Size 15, 2 B-Frames, GOP Closure ivtv0: Audio: 48 kHz, Layer II, 224 kbps, Stereo, No Emphasis, No CRC ivtv0: Spatial Filter: Manual, Luma 1D Horizontal, Chroma 1D Horizontal, 0 ivtv0: Temporal Filter: Manual, 8 ivtv0: Median Filter: Off, Luma [0, 255], Chroma [0, 255] ivtv0: Status flags: 0x00000000 ivtv0: Stream encoder MPEG: status 0x0000, 0% of 4096 KiB (128 buffers) in use ivtv0: Stream encoder YUV: status 0x0000, 0% of 2046 KiB (194 buffers) in use ivtv0: Stream encoder VBI: status 0x0000, 0% of 1023 KiB (60 buffers) in use ivtv0: Stream encoder PCM audio: status 0x0000, 0% of 1021 KiB (227 buffers) in use ivtv0: Read MPEG/VBI: 17614784/0 bytes ivtv0: ================== END STATUS CARD #0 ================== and much more to explain after initiation card: ivtv: ==================== END INIT IVTV ==================== ivtv0: Initialized Adaptec VideOh! AVC-2010, card #0 ivtv0: Registered device video24 for encoder PCM audio (1 MB) ivtv0: Registered device vbi0 for encoder VBI (1 MB) ivtv0: Registered device video32 for encoder YUV (2 MB) ivtv0: Registered device video0 for encoder MPEG (4 MB) cs53l32a 4-0011: chip found @ 0x22 (ivtv i2c driver #0) saa7115 4-0021: saa7115 found (1f7115d0e100000) @ 0x42 (ivtv i2c driver #0) ivtv0: Encoder revision: 0x02060039 ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) ACPI: PCI Interrupt 0000:07:06.0[A] -> GSI 23 (level, low) -> IRQ 21 ivtv0: Autodetected Adaptec VideOh! AVC-2010 card (cx23416 based) ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: In case of problems please include the debug info between ivtv: Linux version: 2.6.21.3 SMP preempt mod_unload CORE2 ivtv: version 0.10.3 (tagged release) loading ivtv: ==================== START INIT IVTV ==================== and after "tail -f /var/log/messages" Jun 20 01:38:44 (none) kernel: ivtv0: Status flags: 0x00000000 Jun 20 01:38:44 (none) kernel: ivtv0: Stream encoder MPEG: status 0x0000, 0%% of 4096 KiB (128 buffers) in use Jun 20 01:38:44 (none) kernel: ivtv0: Stream encoder YUV: status 0x0000, 0%% of 2046 KiB (194 buffers) in use Jun 20 01:38:44 (none) kernel: ivtv0: Stream encoder VBI: status 0x0000, 0%% of 1023 KiB (60 buffers) in use Jun 20 01:38:44 (none) kernel: ivtv0: Stream encoder PCM audio: status 0x0000, 0%% of 1021 KiB (227 buffers) in use Jun 20 01:38:44 (none) kernel: ivtv0: Read MPEG/VBI: 17614784/0 bytes Jun 20 01:38:44 (none) kernel: ivtv0: ================== END STATUS CARD #0 I haven't really idea what's the main point of my problem. I set composite input to play video tape and rip my private tapes from video player into mpg files (every device is made as in README.install is written). Maybe I missed something important because I'm actually newbie in this field. Thanks Peter _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
