Hi Everyone,I am trying to get my PVR-150 working with Ubuntu feisty. I get this message below. After a bit of research I guess this has something to do with a bug? for this chip with certain kernels maybe? I'm pretty new to this, so I have no idea how to fix it. Any ideas?
Thanks again Brett IVTV =/p;/= START INIT IVTV =/q' | tac [ 53.510275] ivtv: ==================== START INIT IVTV ==================== [ 53.510279] ivtv: version 0.10.1 (tagged release) loading [ 53.510281] ivtv: Linux version: 2.6.20-16-generic SMP mod_unload 586 [ 53.510283] ivtv: In case of problems please include the debug info between [ 53.510285] ivtv: the START INIT IVTV and END INIT IVTV lines, along with [ 53.510286] ivtv: any module options, when mailing the ivtv-users mailinglist. [ 53.510393] ivtv0: Autodetected Hauppauge card (cx23416 based) [ 53.510997] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16 [ 53.511005] ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC1] -> GSI 16 (level, high) -> IRQ 20 [ 53.511017] ivtv0: Unreasonably low latency timer, setting to 64 (was 32) [ 53.525721] bcm43xx driver [ 53.545923] usb 2-3: reset full speed USB device using ohci_hcd and address 2 [ 53.772535] lirc_dev: lirc_register_plugin: sample_rate: 0 [ 53.778346] lirc_mceusb2[2]: Philips eHome Infrared Transceiver on usb2:2 [ 53.778382] usbcore: registered new interface driver lirc_mceusb2 [ 54.201438] ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) [ 54.417374] ivtv0: Encoder revision: 0x02050032 [ 54.417378] ivtv0: Recommended firmware version is 0x02060039. [ 54.484321] tveeprom 2-0050: Hauppauge model 26052, rev C185, serial# 7579748 [ 54.484326] tveeprom 2-0050: tuner model is TCL 2002N 6A (idx 85, type 50) [ 54.484329] tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08) [ 54.484331] tveeprom 2-0050: audio processor is CX25843 (idx 37) [ 54.484334] tveeprom 2-0050: decoder processor is CX25843 (idx 30) [ 54.484336] tveeprom 2-0050: has no radio, has IR receiver, has IR transmitter [ 54.484339] ivtv0: Autodetected Hauppauge WinTV PVR-150 [ 54.484341] ivtv0: reopen i2c bus for IR-blaster support [ 54.567954] tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #0) [ 54.802325] wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #0) [ 54.812651] ivtv0: Registered device video0 for encoder MPEG (4 MB) [ 54.812828] ivtv0: Registered device video32 for encoder YUV (2 MB) [ 54.813022] ivtv0: Registered device vbi0 for encoder VBI (1 MB) [ 54.813133] ivtv0: Registered device video24 for encoder PCM audio (1 MB) [ 54.813318] tuner 2-0061: type set to 50 (TCL 2002N) [ 54.813324] ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! [ 54.813328] ivtv0: i2c addr 0x44 not found for command 0x4008646f! [ 54.816433] ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0x4008646d! [ 54.921034] ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! [ 54.922312] ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! [ 55.032960] ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! [ 55.032964] ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 [ 55.032981] ivtv: ==================== END INIT IVTV ====================
_______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
