This card has xceive xc2028 silicon tuner. I put firmware in /lib/firmware folder and load ivtv module again. There is a log: Jul 4 22:51:03 localhost kernel: ivtv: ==================== START INIT IVTV ==================== Jul 4 22:51:03 localhost kernel: ivtv: version 0.10.3 (tagged release) loading Jul 4 22:51:03 localhost kernel: ivtv: Linux version: 2.6.18-1.2798.fc6 SMP mod_unload 686 REGPARM 4KSTACKS gcc-4.1 Jul 4 22:51:03 localhost kernel: ivtv: In case of problems please include the debug info between Jul 4 22:51:03 localhost kernel: ivtv: the START INIT IVTV and END INIT IVTV lines, along with Jul 4 22:51:03 localhost kernel: ivtv: any module options, when mailing the ivtv-users mailinglist. Jul 4 22:51:03 localhost kernel: ivtv0: Unknown card: vendor/device: 4444/0016 Jul 4 22:51:03 localhost kernel: ivtv0: subsystem vendor/device: ffad/0600 Jul 4 22:51:03 localhost kernel: ivtv0: cx23416 based Jul 4 22:51:03 localhost kernel: ivtv0: Defaulting to Hauppauge WinTV PVR-150 card Jul 4 22:51:03 localhost kernel: ivtv0: Please mail the vendor/device and subsystem vendor/device IDs and what kind of Jul 4 22:51:03 localhost kernel: ivtv0: card you have to the ivtv-devel mailinglist (www.ivtvdriver.org) Jul 4 22:51:03 localhost kernel: ivtv0: Prefix your subject line with [UNKNOWN CARD]. Jul 4 22:51:03 localhost kernel: PCI: Enabling device 0000:01:07.0 (0000 -> 0002) Jul 4 22:51:03 localhost kernel: ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC4] -> GSI 19 (level, high) -> IRQ 201 Jul 4 22:51:03 localhost kernel: ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) Jul 4 22:51:03 localhost kernel: ivtv0: Encoder revision: 0x02060039 Jul 4 22:51:04 localhost kernel: cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0) Jul 4 22:51:09 localhost kernel: cx25840 2-0044: loaded v4l-cx25840.fw firmware (16382 bytes) Jul 4 22:51:09 localhost kernel: tveeprom 2-0050: Encountered bad packet header [56]. Corrupt or not a Hauppauge eeprom. Jul 4 22:51:09 localhost kernel: ivtv0: Invalid EEPROM Jul 4 22:51:09 localhost kernel: ivtv0: Registered device video0 for encoder MPEG (4 MB) Jul 4 22:51:09 localhost kernel: ivtv0: Registered device video32 for encoder YUV (2 MB) Jul 4 22:51:09 localhost kernel: ivtv0: Registered device vbi0 for encoder VBI (1 MB) Jul 4 22:51:09 localhost kernel: ivtv0: Registered device video24 for encoder PCM audio (1 MB) Jul 4 22:51:09 localhost kernel: ivtv0: Registered device radio0 for encoder radio Jul 4 22:51:09 localhost kernel: ivtv0: i2c hardware 0x00000020 (wm8775) not found for command 0x4008646d! Jul 4 22:51:10 localhost kernel: ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 Jul 4 22:51:10 localhost kernel: ivtv: ==================== END INIT IVTV ====================
And now i have 3 video devices video0, video24, video32. But i can't get a good image from device ( cat /dev/video0 | mplayer - ) and any sound. I try to use other cardtype (modprobe ivtv cardtype=(15 or 16)), but result is same. _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
