First the boot stuff...
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.10.6 (tagged release) loading
ivtv: Linux version: 2.6.18-92.1.6.el5 SMP mod_unload 686 REGPARM
4KSTACKS gcc-4.1
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge card (cx23415 based)
ACPI: PCI Interrupt 0000:02:0b.0[A] -> GSI 23 (level, low) -> IRQ 177
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02060039
ivtv0: Decoder revision: 0x02020023
tveeprom 1-0050: Hauppauge model 48132, rev K268, serial# 8155290
tveeprom 1-0050: tuner model is LG TAPE H001F MK3 (idx 68, type 47)
tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 1-0050: audio processor is MSP4448 (idx 27)
tveeprom 1-0050: decoder processor is SAA7115 (idx 19)
tveeprom 1-0050: has radio, has IR remote
ivtv0: Autodetected Hauppauge WinTV PVR-350
tuner 1-0043: chip found @ 0x86 (ivtv i2c driver #0)
tda9887 1-0043: tda988[5/6/7] found @ 0x43 (tuner)
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
saa7127 1-0044: saa7129 found @ 0x88 (ivtv i2c driver #0)
msp3400 1-0040: MSP4448G-A2 found @ 0x80 (ivtv i2c driver #0)
msp3400 1-0040: MSP4448G-A2 supports radio, mode is autodetect and
autoselect
ivtv0: Registered device video0 for encoder MPEG (4 MB)
ivtv0: Registered device video32 for encoder YUV (2 MB)
ivtv0: Registered device vbi0 for encoder VBI (1 MB)
ivtv0: Registered device video24 for encoder PCM audio (1 MB)
ivtv0: Registered device radio0 for encoder radio
ivtv0: Registered device video16 for decoder MPEG (1 MB)
ivtv0: Registered device vbi8 for decoder VBI (1 MB)
ivtv0: Registered device vbi16 for decoder VOUT
ivtv0: Registered device video48 for decoder YUV (1 MB)
ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes)
tuner 1-0061: type set to 47 (LG NTSC (TAPE series))
ivtv0: Initialized Hauppauge WinTV PVR-350, card #0
ivtv: ==================== END INIT IVTV ====================
This is a new install of mythtv .21 on a Centos 5.2 server. Card was
pulled out of a .20 server and worked fine prior. I have managed to get
all the other stuff working via a standard video monitor, but I cant
seem to get the video out to work via the PVR which is what is connected
to my tuner. I'm pulling off the composite video , or rather thats the
goal I'm looking to duplicate.
When the machine boots up, my video goes from no display (blue
projection) to a black display. I haven't messed with patching the
initrd file as I dont really care about seeing the boot stuff. I dont
believe thats needed as X is driving the display. Please correct me if
I'm wrong.
I have tried to pull as much as possible from the working xorg.conf file
since that was working pretty well.
in the xorg.0.log file i get:
(II) Module mouse: vendor="X.Org Foundation"
compiled for 7.1.1, module version = 1.1.1
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.6
(II) IVTV: driver for ivtv framebuffer: PVR-350
(II) Primary Device is: PCI 01:00:0
(--) Chipset PVR-350 found
(EE) Unsupported card 'VESA VGA'
(EE) Screen 0 deleted because of no matching config section.
(II) UnloadModule: "ivtv"
(EE) Device(s) detected, but none match those in the config file.
My device isn't at PCI 01:00:0, but at 02.0b.0 per lspci however my
built in video card is at that address.
Finally my xorg.conf.
[EMAIL PROTECTED] log]# vi /etc/X11/xorg.conf
# Xorg configuration created by pyxf86config
Section "ServerLayout"
Identifier "Default Layout"
Screen 0 "TV Screen" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "ServerFlags"
Option "AllowMouseOpenFail" "yes"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection
#Section "Device"
# Identifier "Videocard0"
# Driver "r128"
# Xorg configuration created by pyxf86config
Section "ServerLayout"
Identifier "Default Layout"
Screen 0 "TV Screen" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "ServerFlags"
Option "AllowMouseOpenFail" "yes"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection
#Section "Device"
# Identifier "Videocard0"
# Driver "r128"
#EndSection
Section "Device"
Identifier "Hauppauge PVR-350 Framebuffer"
Driver "ivtv"
Option "fbdev" "/dev/fb0"
Option "VideoOverlay" "on"
Option "XVideo" "1"
BusID "2:11:0"
Screen 0
EndSection
#Section "Screen"
# Identifier "Screen0"
# Device "Videocard0"
# DefaultDepth 24
# SubSection "Display"
# Viewport 0 0
# Depth 24
# EndSubSection
#EndSection
section "Screen"
Identifier "TV Screen"
Device "Hauppauge PVR-350 Framebuffer"
Monitor "NTSC Monitor"
DefaultDepth 24
DefaultFbBpp 32
SubSection "Display"
Depth 24
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
