On Sunday 07 September 2008 18:05:30 Andy Walls wrote: > On Sun, 2008-09-07 at 14:49 -0600, engage wrote: > > >From what I have read, this dmesg output indicates that > > > > ivtv-firmware-20070217-1plf2007.1 should be the correct firmware. The > > PVR-250 works but I get 0 byte files from the PVR-150. Both are installed > > in the same box. > > > > ivtv: Start initialization, version 1.3.0 > > ivtv0: Initializing card #0 > > ivtv0: Autodetected Hauppauge card (cx23416 based) > > ivtv0: Unreasonably low latency timer, setting to 64 (was 32) > > ivtv0: Autodetected Hauppauge WinTV PVR-150 > > ivtv0: Reopen i2c bus for IR-blaster support > > cx25840 0-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #0) > > tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) > > wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0) > > ivtv0: Registered device video0 for encoder MPG (4096 kB) > > ivtv0: Registered device video32 for encoder YUV (2048 kB) > > ivtv0: Registered device vbi0 for encoder VBI (1024 kB) > > ivtv0: Registered device video24 for encoder PCM (320 kB) > > ivtv0: Initialized card #0: Hauppauge WinTV PVR-150 > > ivtv1: Initializing card #1 > > ivtv1: Autodetected Hauppauge card (cx23416 based) > > ivtv1: Unreasonably low latency timer, setting to 64 (was 32) > > ivtv1: Autodetected Hauppauge WinTV PVR-250 > > saa7115 1-0021: saa7115 found (1f7115d0e100000) @ 0x42 (ivtv i2c driver > > #1) msp3400 1-0040: MSP3435G-B6 found @ 0x80 (ivtv i2c driver #1) > > tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #1) > > ivtv1: Registered device video1 for encoder MPG (4096 kB) > > ivtv1: Registered device video33 for encoder YUV (2048 kB) > > ivtv1: Registered device vbi1 for encoder VBI (1024 kB) > > ivtv1: Registered device video25 for encoder PCM (320 kB) > > ivtv1: Initialized card #1: Hauppauge WinTV PVR-250 > > ivtv: End initialization > > ivtv0: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes) > > ivtv0: Encoder revision: 0x02060039 > > [<f8e57ae0>] (ivtv_irq_handler+0x0/0x12f0 [ivtv]) > > Something bad happened here. Likely a kernel oops. Don't just grep for > ivtv. PLease give the whole log between start and end initialization.
That is what is in the log from start to finish during initialization. There are no errors or warnings. > > > ivtv1: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes) > > ivtv1: Encoder revision: 0x02060039 > > [EMAIL PROTECTED] ~]$ rpm -qa | grep ivtv > > ivtv-firmware-20070217-1plf2007.1 > > perl-Video-ivtv-0.13-3mdv2008.1 > > ivtv-0.10-0.10.2-3mdv2008.1 > > As for what firmware to use, maybe you can look in this directory: > > http://dl.ivtvdriver.org/ivtv/firmware/ I'd rather use the rpm package. > > The readme file may help. It says all the firmware files you would need > are in: > > http://dl.ivtvdriver.org/ivtv/firmware/ivtv-firmware.tar.gz > > > (I only have a PVR-150MCE myself and I used the firmware that came with > the Windows driver.) > > Regards, > Andy > > > > > > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
