I don't know what you're looking for but here's the complete output from
dmesg:
Linux version 2.6.26-desktop-1mnb ([EMAIL PROTECTED]) (gcc version 4.2.3
(4.2.3-6mnb1)) #1 SMP Thu Jul 17 07:38:12 EDT 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003bff0000 (usable)
BIOS-e820: 000000003bff0000 - 000000003bff3000 (ACPI NVS)
BIOS-e820: 000000003bff3000 - 000000003c000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
63MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at [c00f4e30] 000f4e30
Entering add_active_range(0, 0, 245744) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 245744
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 245744
On node 0 totalpages: 245744
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 128 pages used for memmap
HighMem zone: 16240 pages, LIFO batch:3
Movable zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000F8CA0, 0014 (r0 VIAK8M)
ACPI: RSDT 3BFF3040, 002C (r1 VIAK8M AWRDACPI 42302E31 AWRD 0)
ACPI: FACP 3BFF30C0, 0074 (r1 VIAK8M AWRDACPI 42302E31 AWRD 0)
ACPI: DSDT 3BFF3180, 4D34 (r1 VIAK8M AWRDACPI 1000 MSFT 100000E)
ACPI: FACS 3BFF0000, 0040
ACPI: APIC 3BFF7F00, 005A (r1 VIAK8M AWRDACPI 42302E31 AWRD 0)
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 3c000000:c2c00000)
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
SMP: Allowing 1 CPUs, 0 hotplug CPUs
PERCPU: Allocating 41256 bytes of per cpu data
NR_CPUS: 32, nr_cpu_ids: 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 243824
Kernel command line: auto BOOT_IMAGE=linux root=301 resume=/dev/hda5
splash=silent
bootsplash: silent mode.
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1999.870 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 967000k/982976k available (2367k kernel code, 15480k reserved, 1067k
data, 320k init, 65472k highmem)
virtual kernel memory layout:
fixmap : 0xffe14000 - 0xfffff000 (1964 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc0463000 - 0xc04b3000 ( 320 kB)
.data : 0xc034fd09 - 0xc045aa40 (1067 kB)
.text : 0xc0100000 - 0xc034fd09 (2367 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 4002.76 BogoMIPS
(lpj=2001383)
Security Framework initialized
AppArmor: AppArmor disabled by boottime parameter
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 18k freed
Early unpacking initramfs... done
Freeing initrd memory: 2593k freed
ACPI: Core revision 20080321
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0
CPU0: AMD Athlon(tm) 64 Processor 3000+ stepping 0a
Brought up 1 CPUs
Total of 1 processors activated (4002.76 BogoMIPS).
CPU0 attaching sched-domain:
domain 0: span 0
groups: 0
net_namespace: 660 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb160, last bus=1
PCI: Using configuration type 1 for base access
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI Error (dsobject-0501): Package List length (6) larger than NumElements
count (3), truncated
[20080321]
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 11 12) *5
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [ALKA] (IRQs *20)
ACPI: PCI Interrupt Link [ALKB] (IRQs *21)
ACPI: PCI Interrupt Link [ALKC] (IRQs *22)
ACPI: PCI Interrupt Link [ALKD] (IRQs *23)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
ACPI: RTC can wake from S4
system 00:00: iomem range 0xcc000-0xcffff has been reserved
system 00:00: iomem range 0xd8c00-0xdbfff has been reserved
system 00:00: iomem range 0xf0000-0xfbfff could not be reserved
system 00:00: iomem range 0xfc000-0xfffff could not be reserved
system 00:00: iomem range 0x3bff0000-0x3bffffff could not be reserved
system 00:00: iomem range 0xffff0000-0xffffffff could not be reserved
system 00:00: iomem range 0x0-0x9ffff could not be reserved
system 00:00: iomem range 0x100000-0x3bfeffff could not be reserved
system 00:00: iomem range 0x3c000000-0x3fffffff has been reserved
system 00:00: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:00: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:00: iomem range 0xfff80000-0xfffeffff has been reserved
system 00:02: ioport range 0x4000-0x407f has been reserved
system 00:02: ioport range 0x5000-0x500f has been reserved
system 00:03: ioport range 0xb78-0xb7b has been reserved
system 00:03: ioport range 0xf78-0xf7b has been reserved
system 00:03: ioport range 0xa78-0xa7b has been reserved
system 00:03: ioport range 0xe78-0xe7b has been reserved
system 00:03: ioport range 0xbbc-0xbbf has been reserved
system 00:03: ioport range 0xfbc-0xfbf has been reserved
system 00:03: ioport range 0x4d0-0x4d1 has been reserved
system 00:03: ioport range 0x290-0x297 has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: 0xf4000000-0xf5ffffff
PREFETCH window: 0x00000000e8000000-0x00000000ebffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
type=2000 audit(1220813012.297:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1766
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: VIA PCI bridge detected.Disabling DAC.
pci 0000:01:00.0: Boot video device
vesafb: framebuffer at 0xe8000000, mapped to 0xf8880000, using 3750k, total
65536k
vesafb: mode is 800x600x16, linelength=1600, pages=63
vesafb: protected mode interface info at c000:6bf7
vesafb: pmi: set display start = c00c6c45, set palette = c00c6cb6
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 221130
bytes,<6>...found (800x600, 221034 bytes, v3).
Console: switching to colour frame buffer device 91x30
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
Switched to high resolution mode on CPU 0
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
brd: module loaded
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
Using IPI No-Shortcut mode
registered taskstats version 1
BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
Freeing unused kernel memory: 320k freed
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [ALKB] -> GSI 21 (level, low) ->
IRQ 21
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 21, io mem 0xf6001000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.26-desktop-1mnb ehci_hcd
usb usb1: SerialNumber: 0000:00:10.4
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21 (level, low) ->
IRQ 21
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 21, io base 0x0000e800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.26-desktop-1mnb uhci_hcd
usb usb2: SerialNumber: 0000:00:10.0
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [ALKB] -> GSI 21 (level, low) ->
IRQ 21
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 21, io base 0x0000e900
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.26-desktop-1mnb uhci_hcd
usb usb3: SerialNumber: 0000:00:10.1
ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [ALKB] -> GSI 21 (level, low) ->
IRQ 21
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 21, io base 0x0000ea00
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 3-1: new low speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: New USB device found, idVendor=051d, idProduct=0002
usb 3-1: New USB device strings: Mfr=3, Product=1, SerialNumber=2
usb 3-1: Product: Back-UPS ES 350 FW:800.e5.D USB FW:e5
usb 3-1: Manufacturer: APC
usb 3-1: SerialNumber: AB0435243830
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.26-desktop-1mnb uhci_hcd
usb usb4: SerialNumber: 0000:00:10.2
ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [ALKB] -> GSI 21 (level, low) ->
IRQ 21
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 21, io base 0x0000eb00
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.26-desktop-1mnb uhci_hcd
usb usb5: SerialNumber: 0000:00:10.3
Uniform Multi-Platform E-IDE driver
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller (0x1106:0x0571 rev 0x06) at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:0f.1[A] -> Link [ALKA] -> GSI 20 (level, low) ->
IRQ 20
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xe700-0xe707
ide1: BM-DMA at 0xe708-0xe70f
Probing IDE interface ide0...
hda: Maxtor 5T040H4, ATA DISK drive
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
Probing IDE interface ide1...
hdc: TOSHIBA CD-ROM XM-6202B, ATAPI CD/DVD-ROM drive
hdd: LITE-ON DVDRW SOHW-1653S, ATAPI CD/DVD-ROM drive
hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdc: MWDMA2 mode selected
hdd: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdd: UDMA/66 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 80043264 sectors (40982 MB) w/2048KiB Cache, CHS=65535/16/63
hda: cache flushes not supported
hda: hda1 hda2 < hda5 hda6 hda7 >
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Linux agpgart interface v0.103
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 128M @ 0xe0000000
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: ACPI0007:00 is registered as cooling_device0
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
Linux video capture interface: v2.00
ivtv: Start initialization, version 1.3.0
ivtv0: Initializing card #0
ivtv0: Autodetected Hauppauge card (cx23416 based)
ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 16 (level, low) -> IRQ 16
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
tveeprom 0-0050: Hauppauge model 26152, rev E5B2, serial# 10388716
tveeprom 0-0050: tuner model is TCL M2523_5N_E (idx 112, type 50)
tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 0-0050: audio processor is CX25843 (idx 37)
tveeprom 0-0050: decoder processor is CX25843 (idx 30)
tveeprom 0-0050: has no radio, has IR receiver, has IR transmitter
ivtv0: Autodetected Hauppauge WinTV PVR-150
ivtv0: Reopen i2c bus for IR-blaster support
cx25840 0-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #0)
tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
tuner-simple 0-0061: creating new instance
tuner-simple 0-0061: type set to 50 (TCL 2002N)
ivtv0: Registered device video0 for encoder MPG (4096 kB)
ivtv0: Registered device video32 for encoder YUV (2048 kB)
ivtv0: Registered device vbi0 for encoder VBI (1024 kB)
ivtv0: Registered device video24 for encoder PCM (320 kB)
ivtv0: Initialized card #0: Hauppauge WinTV PVR-150
ivtv1: Initializing card #1
ivtv1: Autodetected Hauppauge card (cx23416 based)
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 17
ivtv1: Unreasonably low latency timer, setting to 64 (was 32)
tveeprom 1-0050: Hauppauge model 32031, rev B110, serial# 6149459
tveeprom 1-0050: tuner model is Philips FI1236 MK2 (idx 10, type 2)
tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 1-0050: audio processor is MSP3435 (idx 10)
tveeprom 1-0050: decoder processor is SAA7115 (idx 19)
tveeprom 1-0050: has no radio, has IR receiver, has no IR transmitter
ivtv1: Autodetected Hauppauge WinTV PVR-250
saa7115 1-0021: saa7115 found (1f7115d0e100000) @ 0x42 (ivtv i2c driver #1)
hdc: ATAPI 32X CD-ROM drive, 256kB Cache
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
via-rhine: Broken BIOS detected, avoid_D3 enabled.
usbcore: registered new interface driver hiddev
msp3400 1-0040: MSP3435G-B6 found @ 0x80 (ivtv i2c driver #1)
msp3400 1-0040: msp3400 supports radio, mode is autodetect and autoselect
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #1)
tuner-simple 1-0061: creating new instance
tuner-simple 1-0061: type set to 2 (Philips NTSC (FI1236,FM1236 and
compatibles))
ivtv1: Registered device video1 for encoder MPG (4096 kB)
ivtv1: Registered device video33 for encoder YUV (2048 kB)
ivtv1: Registered device vbi1 for encoder VBI (1024 kB)
ivtv1: Registered device video25 for encoder PCM (320 kB)
ivtv1: Initialized card #1: Hauppauge WinTV PVR-250
ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [ALKD] -> GSI 23 (level, low) ->
IRQ 23
eth0: VIA Rhine II at 0x1ed00, 00:16:17:20:5b:aa, IRQ 23.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
ivtv: End initialization
ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) ->
IRQ 22
PCI: Setting latency timer of device 0000:00:11.5 to 64
rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k
parport_pc 00:0b: reported by Plug and Play ACPI
parport0: PC-style at 0x378, irq 7 [PCSPP]
hiddev0hidraw0: USB HID v1.10 Device [APC Back-UPS ES 350 FW:800.e5.D USB
FW:e5] on usb-0000:00:10.1-1
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3000+ processors (1 cpu
cores) (version 2.20.00)
powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x2
powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x6
powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0x12
FDC 0 is a post-1991 82077
SCSI subsystem initialized
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 18
ahc_pci:0:10:0: Host Adapter Bios disabled. Using default SCSI device
parameters
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<Adaptec aic7850 SCSI adapter>
aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs
scsi 0:0:2:0: Processor EPSON Perfection636 1.09 PQ: 0 ANSI: 2
target0:0:2: Beginning Domain Validation
target0:0:2: Ending Domain Validation
scsi 0:0:2:0: Attached scsi generic sg0 type 3
No dock devices found.
libata version 3.00 loaded.
sata_via 0000:00:0f.0: version 2.3
ACPI: PCI Interrupt 0000:00:0f.0[B] -> Link [ALKA] -> GSI 20 (level, low) ->
IRQ 20
sata_via 0000:00:0f.0: routed to hard irq line 10
scsi1 : sata_via
scsi2 : sata_via
ata1: SATA max UDMA/133 cmd 0xe100 ctl 0xe200 bmdma 0xe500 irq 20
ata2: SATA max UDMA/133 cmd 0xe300 ctl 0xe400 bmdma 0xe508 irq 20
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: ST3500630AS, 3.AAK, max UDMA/133
ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATA-7: WDC WD5000YS-01MPB0, 07.02E07, max UDMA/133
ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5
scsi 1:0:0:0: Attached scsi generic sg1 type 0
scsi 2:0:0:0: Direct-Access ATA WDC WD5000YS-01M 07.0 PQ: 0 ANSI: 5
scsi 2:0:0:0: Attached scsi generic sg2 type 0
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
Driver 'sd' needs updating - please use bus_type methods
sd 1:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 1:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sda: sda1
sd 1:0:0:0: [sda] Attached SCSI disk
sd 2:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 2:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sdb: sdb1
sd 2:0:0:0: [sdb] Attached SCSI disk
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised:
[EMAIL PROTECTED]
EXT3 FS on hda1, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
loop: module loaded
Adding 1638588k swap on /dev/hda5. Priority:-1 extents:1 across:1638588k
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 221130
bytes,<6>...found (800x600, 221034 bytes, v3).
bootsplash: status on console 0 changed to on
nf_conntrack version 0.5.0 (15360 buckets, 61440 max)
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
NET: Registered protocol family 17
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
ip_tables: (C) 2000-2006 Netfilter Core Team
eth0: no IPv6 routers present
firmware: requesting v4l-cx2341x-enc.fw
[drm] Initialized drm 1.1.0 20060810
warning: `proftpd' uses 32-bit capabilities (legacy support in use)
ivtv0: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized via 2.11.1 20070202 on minor 0
ivtv0: Encoder revision: 0x02060039
firmware: requesting v4l-cx25840.fw
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: X tried to set rate=x12. Setting to AGP3 x8 mode.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
irq 16: nobody cared (try booting with the "irqpoll" option)
Pid: 4362, comm: automount Not tainted 2.6.26-desktop-1mnb #1
[<c0163e37>] __report_bad_irq+0x27/0x90
[<c0164106>] note_interrupt+0x266/0x2a0
[<c0163398>] ? handle_IRQ_event+0x38/0x80
[<c01649c0>] handle_fasteoi_irq+0x80/0xd0
[<c0106ca0>] do_IRQ+0x40/0x80
[<c01047ef>] common_interrupt+0x23/0x28
[<c016af81>] ? generic_file_aio_read+0x21/0x5c0
[<c01047ef>] ? common_interrupt+0x23/0x28
[<c01f46a1>] ? dummy_dentry_open+0x1/0x10
[<c018e6a2>] ? __dentry_open+0x192/0x230
[<c018e787>] ? nameidata_to_filp+0x47/0x60
[<c019000d>] do_sync_read+0xcd/0x110
[<c01401c0>] ? autoremove_wake_function+0x0/0x40
[<c01f2d2f>] ? security_file_permission+0xf/0x20
[<c01900a7>] ? rw_verify_area+0x57/0xc0
[<c01990a5>] ? putname+0x25/0x40
[<c0190934>] vfs_read+0x94/0x160
[<c018ff40>] ? do_sync_read+0x0/0x110
[<c0190e5d>] sys_read+0x3d/0x70
[<c0103e16>] syscall_call+0x7/0xb
=======================
handlers:
[<f8e55ae0>] (ivtv_irq_handler+0x0/0x12f0 [ivtv])
[<f8cfa3f0>] (via_driver_irq_handler+0x0/0x1c0 [via])
Disabling IRQ #16
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (15360 buckets, 61440 max)
cx25840 0-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
firmware: requesting v4l-cx2341x-enc.fw
ivtv1: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ctnetlink v0.93: registering with nfnetlink.
ivtv1: Encoder revision: 0x02060039
ClusterIP Version 0.8 loaded successfully
netfilter PSD loaded - (c) astaro AG
IFWLOG: register target
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14966
bytes, v3).
bootsplash: status on console 0 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14966
bytes, v3).
bootsplash: status on console 1 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14966
bytes, v3).
bootsplash: status on console 2 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14966
bytes, v3).
bootsplash: status on console 3 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14966
bytes, v3).
bootsplash: status on console 4 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14966
bytes, v3).
bootsplash: status on console 5 changed to on
Shorewall:net2fw:DROP:IN=eth0 OUT=
MAC=00:16:17:20:5b:aa:00:12:17:e2:8d:03:08:00 SRC=93.186.176.224
DST=192.168.1.4 LEN=60 TOS=0x00 PREC=0x00 TTL=45 ID=14797 DF PROTO=TCP
SPT=48401 DPT=6891 WINDOW=5840 RES=0x00 SYN URGP=0
Shorewall:net2fw:DROP:IN=eth0 OUT=
MAC=00:16:17:20:5b:aa:00:12:17:e2:8d:03:08:00 SRC=93.186.176.224
DST=192.168.1.4 LEN=60 TOS=0x00 PREC=0x00 TTL=45 ID=49696 DF PROTO=TCP
SPT=57912 DPT=6891 WINDOW=5840 RES=0x00 SYN URGP=0
Shorewall:net2fw:DROP:IN=eth0 OUT=
MAC=00:16:17:20:5b:aa:00:12:17:e2:8d:03:08:00 SRC=201.193.1.129
DST=192.168.1.4 LEN=48 TOS=0x00 PREC=0x00 TTL=111 ID=64894 DF PROTO=TCP
SPT=1994 DPT=6891 WINDOW=65535 RES=0x00 SYN URGP=0
Shorewall:net2fw:DROP:IN=eth0 OUT=
MAC=00:16:17:20:5b:aa:00:12:17:e2:8d:03:08:00 SRC=201.193.1.129
DST=192.168.1.4 LEN=48 TOS=0x00 PREC=0x00 TTL=111 ID=20413 DF PROTO=TCP
SPT=2140 DPT=6893 WINDOW=65535 RES=0x00 SYN URGP=0
Shorewall:net2fw:DROP:IN=eth0 OUT=
MAC=00:16:17:20:5b:aa:00:12:17:e2:8d:03:08:00 SRC=201.193.1.129
DST=192.168.1.4 LEN=48 TOS=0x00 PREC=0x00 TTL=111 ID=20457 DF PROTO=TCP
SPT=2140 DPT=6893 WINDOW=65535 RES=0x00 SYN URGP=0
Shorewall:net2fw:DROP:IN=eth0 OUT=
MAC=00:16:17:20:5b:aa:00:12:17:e2:8d:03:08:00 SRC=93.186.176.224
DST=192.168.1.4 LEN=60 TOS=0x00 PREC=0x00 TTL=45 ID=342 DF PROTO=TCP
SPT=56652 DPT=6891 WINDOW=5840 RES=0x00 SYN URGP=0
Shorewall:net2fw:DROP:IN=eth0 OUT=
MAC=00:16:17:20:5b:aa:00:12:17:e2:8d:03:08:00 SRC=93.186.176.224
DST=192.168.1.4 LEN=60 TOS=0x00 PREC=0x00 TTL=45 ID=56675 DF PROTO=TCP
SPT=33300 DPT=6891 WINDOW=5840 RES=0x00 SYN URGP=0
On Wednesday 10 September 2008 18:56:24 Andy Walls wrote:
> On Tue, 2008-09-09 at 19:59 -0600, engage wrote:
> > Well Andy, I downloaded and extracted the tarball & compared the
> > extracted firmware files to the firmware in /lib/firmware/ and they are a
> > match. In other words, I already had the firmware installed.
>
> OK. One unknown eliminated.
>
> > So, there must be another
> > issue at work here.
>
> Yup. There has to be. See below....
>
> > Google hasn't been much help concerning this issue
> > either. And I'm not getting any replies in #ivtv-dev either.
> >
> > On Sunday 07 September 2008 19:09:49 engage wrote:
> > > On Sunday 07 September 2008 18:05:30 Andy Walls wrote:
> > > > On Sun, 2008-09-07 at 14:49 -0600, engage wrote:
> > > > > >From what I have read, this dmesg output indicates that
> > > > >
> > > > > ivtv-firmware-20070217-1plf2007.1 should be the correct firmware.
> > > > > The PVR-250 works but I get 0 byte files from the PVR-150. Both are
> > > > > installed in the same box.
> > > > >
> > > > > ivtv: Start initialization, version 1.3.0
> > > > > ivtv0: Initializing card #0
> > > > > ivtv0: Autodetected Hauppauge card (cx23416 based)
> > > > > ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
> > > > > ivtv0: Autodetected Hauppauge WinTV PVR-150
> > > > > ivtv0: Reopen i2c bus for IR-blaster support
> > > > > cx25840 0-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #0)
> > > > > tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
> > > > > wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
> > > > > ivtv0: Registered device video0 for encoder MPG (4096 kB)
> > > > > ivtv0: Registered device video32 for encoder YUV (2048 kB)
> > > > > ivtv0: Registered device vbi0 for encoder VBI (1024 kB)
> > > > > ivtv0: Registered device video24 for encoder PCM (320 kB)
> > > > > ivtv0: Initialized card #0: Hauppauge WinTV PVR-150
> > > > > ivtv1: Initializing card #1
> > > > > ivtv1: Autodetected Hauppauge card (cx23416 based)
> > > > > ivtv1: Unreasonably low latency timer, setting to 64 (was 32)
> > > > > ivtv1: Autodetected Hauppauge WinTV PVR-250
> > > > > saa7115 1-0021: saa7115 found (1f7115d0e100000) @ 0x42 (ivtv i2c
> > > > > driver #1) msp3400 1-0040: MSP3435G-B6 found @ 0x80 (ivtv i2c
> > > > > driver #1) tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #1)
> > > > > ivtv1: Registered device video1 for encoder MPG (4096 kB)
> > > > > ivtv1: Registered device video33 for encoder YUV (2048 kB)
> > > > > ivtv1: Registered device vbi1 for encoder VBI (1024 kB)
> > > > > ivtv1: Registered device video25 for encoder PCM (320 kB)
> > > > > ivtv1: Initialized card #1: Hauppauge WinTV PVR-250
> > > > > ivtv: End initialization
> > > > > ivtv0: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
> > > > > ivtv0: Encoder revision: 0x02060039
> > > > > [<f8e57ae0>] (ivtv_irq_handler+0x0/0x12f0 [ivtv])
>
> The above line is *not* emitted by the ivtv driver. This sort of line
> is usually emitted by another part of the kernel that trapped something
> bad. The dump from the trap usually includes a lot more context. (See
> linux/arch/x86/kernel/traps_32.c)
>
>
> Since the log you provided had "ivtv" on every line, I assumed you did a
> 'dmesg | grep ivtv' or something similar to generate the log output.
>
> The problem is, I cannot help you resolve your problem without all that
> additional debug context that the kernel outputs. One line telling me
> that something happened at offset 0 of the ivtv_irq_handler() is not
> enough to work with.
>
> Please carefully check the dmesg or /var/log/messages output for a full
> dump from the kernel. That'll at least give me some hope of telling you
> what has happened. All I can tell you right now is that setup of the
> driver for one card probably failed. But you already knew that. :)
>
> Regards,
> Andy
>
> > > > Something bad happened here. Likely a kernel oops. Don't just grep
> > > > for ivtv. PLease give the whole log between start and end
> > > > initialization.
> > >
> > > That is what is in the log from start to finish during initialization.
> > > There are no errors or warnings.
> > >
> > > > > ivtv1: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
> > > > > ivtv1: Encoder revision: 0x02060039
> > > > > [EMAIL PROTECTED] ~]$ rpm -qa | grep ivtv
> > > > > ivtv-firmware-20070217-1plf2007.1
> > > > > perl-Video-ivtv-0.13-3mdv2008.1
> > > > > ivtv-0.10-0.10.2-3mdv2008.1
> > > >
> > > > As for what firmware to use, maybe you can look in this directory:
> > > >
> > > > http://dl.ivtvdriver.org/ivtv/firmware/
> > >
> > > I'd rather use the rpm package.
> > >
> > > > The readme file may help. It says all the firmware files you would
> > > > need are in:
> > > >
> > > > http://dl.ivtvdriver.org/ivtv/firmware/ivtv-firmware.tar.gz
> > > >
> > > >
> > > > (I only have a PVR-150MCE myself and I used the firmware that came
> > > > with the Windows driver.)
> > > >
> > > > Regards,
> > > > Andy
>
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
