Thanks for the response. Here is everything between the start and end of the cx18 initialization, including a few seemingly irrelevant entries just in case.
[ 47.395294] cx18: Start initialization, version 1.0.1 [ 47.395465] cx18-0: Initializing card #0 [ 47.395474] cx18-0: Autodetected Hauppauge card [ 47.395905] cx18-0: cx23418 revision 01010000 (B) [ 47.892914] tveeprom 1-0050: Hauppauge model 74551, rev C1A3, serial# 1825556 [ 47.892926] tveeprom 1-0050: MAC address is 00-0D-FE-1B-DB-14 [ 47.892932] tveeprom 1-0050: tuner model is TCL MFNM05-4 (idx 103, type 43) [ 47.892939] tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08) [ 47.892945] tveeprom 1-0050: audio processor is CX23418 (idx 38) [ 47.892950] tveeprom 1-0050: decoder processor is CX23418 (idx 31) [ 47.892955] tveeprom 1-0050: has radio [ 47.892961] cx18-0: Autodetected Hauppauge HVR-1600 [ 47.892966] cx18-0: VBI is not yet supported [ 48.657268] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 [ 48.864454] eth1: link up, 10Mbps, half-duplex, lpa 0x0000 [ 48.895902] eth1: link down [ 49.540757] usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x03F0 pid 0xB402 [ 49.540822] usbcore: registered new interface driver usblp [ 49.687630] eth1: link up, 10Mbps, half-duplex, lpa 0x0000 [ 49.698112] tuner 2-0043: chip found @ 0x86 (cx18 i2c driver #0-1) [ 49.791974] eth1: link down [ 50.085526] tda9887 2-0043: creating new instance [ 50.085537] tda9887 2-0043: tda988[5/6/7] found [ 50.087385] tuner 2-0061: chip found @ 0xc2 (cx18 i2c driver #0-1) [ 50.087434] cs5345 1-004c: chip found @ 0x98 (cx18 i2c driver #0-0) [ 50.199493] eth1: link up, 10Mbps, half-duplex, lpa 0x0000 [ 50.228825] eth1: link down [ 50.461207] NET: Registered protocol family 10 [ 50.461772] lo: Disabled Privacy Extensions [ 50.511323] tuner-simple 2-0061: creating new instance [ 50.511338] tuner-simple 2-0061: type set to 43 (Philips NTSC MK3 (FM1236MK3 or FM1236/F)) [ 50.513447] cx18-0: Disabled encoder IDX device [ 50.513582] cx18-0: Registered device video0 for encoder MPEG (2 MB) [ 50.513591] DVB: registering new adapter (cx18) [ 50.567843] NET: Registered protocol family 17 [ 50.583395] eth1: link up, 10Mbps, half-duplex, lpa 0x0000 [ 50.688056] eth1: link down [ 50.759804] s5h1409_readreg: readreg error (ret == -121) [ 50.759912] cx18-0: frontend initialization failed [ 50.760281] cx18-0: DVB failed to register [ 50.760358] cx18-0: Registered device video32 for encoder YUV (2 MB) [ 50.760397] cx18-0: Registered device video24 for encoder PCM audio (1 MB) [ 50.760438] cx18-0: Registered device radio0 for encoder radio [ 50.760880] cx18-0: Error -1 registering devices [ 50.761002] tda9887 2-0043: destroying instance [ 50.761046] tuner-simple 2-0061: destroying instance [ 50.761945] cx18-0: Error -1 on initialization [ 50.761970] cx18: probe of 0000:00:0f.0 failed with error -1 [ 50.762010] cx18: End initialization This appears to be where it fails: [ 50.759804] s5h1409_readreg: readreg error (ret == -121) find / -name *s5h1409* reveals: /lib/modules/2.6.24-19-generic/kernel/drivers/media/dvb/frontends/s5h1409.ko /lib/modules/2.6.24-21-generic/kernel/drivers/media/dvb/frontends/s5h1409.ko find: /home/sam/.gvfs: Permission denied /usr/src/linux-headers-2.6.24-21/drivers/media/dvb/frontends/s5h1409.h /usr/src/linux-headers-2.6.24-21-generic/include/config/dvb/s5h1409.h /usr/src/linux-headers-2.6.24-19/drivers/media/dvb/frontends/s5h1409.h /usr/src/linux-headers-2.6.24-19-generic/include/config/dvb/s5h1409.h /sys/module/s5h1409 /root/v4l-dvb/v4l/s5h1409.ko /root/v4l-dvb/v4l/s5h1409.mod.c /root/v4l-dvb/v4l/.s5h1409.ko.cmd /root/v4l-dvb/v4l/.s5h1409.o.cmd /root/v4l-dvb/v4l/s5h1409.c /root/v4l-dvb/v4l/s5h1409.h /root/v4l-dvb/v4l/.s5h1409.mod.o.cmd /root/v4l-dvb/v4l/.tmp_versions/s5h1409.mod /root/v4l-dvb/v4l/s5h1409.o /root/v4l-dvb/v4l/s5h1409.mod.o /root/v4l-dvb/.hg/store/data/linux/drivers/media/dvb/frontends/s5h1409.c.i /root/v4l-dvb/.hg/store/data/linux/drivers/media/dvb/frontends/s5h1409.h.i /root/v4l-dvb/linux/drivers/media/dvb/frontends/s5h1409.c /root/v4l-dvb/linux/drivers/media/dvb/frontends/s5h1409.h find / -name *mxl5005s* reveals: /lib/modules/2.6.24-21-generic/kernel/drivers/media/common/tuners/mxl5005s.ko find: /home/sam/.gvfs: Permission denied /root/v4l-dvb/v4l/mxl5005s.mod.o /root/v4l-dvb/v4l/mxl5005s.mod.c /root/v4l-dvb/v4l/mxl5005s.h /root/v4l-dvb/v4l/.mxl5005s.mod.o.cmd /root/v4l-dvb/v4l/.mxl5005s.o.cmd /root/v4l-dvb/v4l/.mxl5005s.ko.cmd /root/v4l-dvb/v4l/mxl5005s.ko /root/v4l-dvb/v4l/mxl5005s.o /root/v4l-dvb/v4l/.tmp_versions/mxl5005s.mod /root/v4l-dvb/v4l/mxl5005s.c /root/v4l-dvb/.hg/store/data/linux/drivers/media/common/tuners/mxl5005s.h.i /root/v4l-dvb/.hg/store/data/linux/drivers/media/common/tuners/mxl5005s.c.i /root/v4l-dvb/linux/drivers/media/common/tuners/mxl5005s.h /root/v4l-dvb/linux/drivers/media/common/tuners/mxl5005s.c Could something be in the wrong place? On Sat, 2008-10-25 at 13:23 -0400, Andy Walls wrote: > On Fri, 2008-10-24 at 16:08 -0400, sam wrote: > > So I've searched all over the net, and I'm basically stumped. > > > > I followed the directions here > > (http://www.mythtv.org/wiki/index.php/Hauppauge_HVR-1600) for compiling > > and installing the cx-18 driver for use with hvr-1600. I'm using ubuntu > > feisty. > > > > Here's the ouput of dmesg | grep cx-18: > > > > [ 47.395294] cx18: Start initialization, version 1.0.1 > > [ 47.395465] cx18-0: Initializing card #0 > > [ 47.395474] cx18-0: Autodetected Hauppauge card > > [ 47.395905] cx18-0: cx23418 revision 01010000 (B) > > [ 47.892961] cx18-0: Autodetected Hauppauge HVR-1600 > > [ 47.892966] cx18-0: VBI is not yet supported > > [ 49.698112] tuner 2-0043: chip found @ 0x86 (cx18 i2c driver #0-1) > > [ 50.087385] tuner 2-0061: chip found @ 0xc2 (cx18 i2c driver #0-1) > > [ 50.087434] cs5345 1-004c: chip found @ 0x98 (cx18 i2c driver #0-0) > > [ 50.513447] cx18-0: Disabled encoder IDX device > > [ 50.513582] cx18-0: Registered device video0 for encoder MPEG (2 MB) > > [ 50.513591] DVB: registering new adapter (cx18) > > [ 50.759912] cx18-0: frontend initialization failed > > [ 50.760281] cx18-0: DVB failed to register > > [ 50.760358] cx18-0: Registered device video32 for encoder YUV (2 MB) > > [ 50.760397] cx18-0: Registered device video24 for encoder PCM audio > > (1 MB) > > [ 50.760438] cx18-0: Registered device radio0 for encoder radio > > [ 50.760880] cx18-0: Error -1 registering devices > > [ 50.761945] cx18-0: Error -1 on initialization > > [ 50.761970] cx18: probe of 0000:00:0f.0 failed with error -1 > > [ 50.762010] cx18: End initialization > > Please provide the full output (don't grep on cx18) between "cx18: Start > initialization" and "cx18: End initialization" > > Given the grepped output above, everything appears to be OK with the > analog side of the card. The DVB (ATSC) initialization for digital > video failed in linux/drivers/media/video/cx18/cx18-dvb.c:dvb_register() > at about line 291. > > (BTW, I need to fix the return value of -1 to something more meaningful. > -1 is -EPERM, "operation not permitted" which is the wrong error code > here.) > > > > This seems a little bit similar to the "invalid EPROM" errors people > > were getting, > > But it's not, AFAICT. > > My suspicions are either that you don't have the s5h1409 and mxl5005s > modules built and installed, or you have disabled dynamic loading of > modules upon kernel request somehow. > > > > however I tried the fix (reloading cx-18 with mmio_ndelay > > 31) with no success. I'd appreciate any help. > > > With the cx18 driver v1.0.1 default setting of retry_mmio=1 being set, > mmio_ndelay has a vanishingly small effect. Don't bother with it. It > won't help, nor do you have the specific problem with which it could > help, AFAICT. > > Regards, > Andy > > > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
