No changes. It works just like before. It loads fine, but no data is captured. dmesg output after "modprobe cx18 debug=511":
cx18: Start initialization, version 1.0.1 cx18-0: Initializing card #0 cx18-0: Autodetected Hauppauge card cx18-0 info: base addr: 0xe8000000 cx18-0 info: Enabling pci device ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 21 (level, low) -> IRQ 21 cx18-0 info: cx23418 (rev 0) at 02:01.0, irq: 21, latency: 64, memory: 0xe8000000 cx18-0 info: attempting ioremap at 0xe8000000 len 0x04000000 cx18-0: cx23418 revision 01010000 (B) cx18-0 info: GPIO initial dir: 0000cffe/0000ffff out: 00003001/00000000 cx18-0 info: activating i2c... cx18-0 i2c: i2c init cx18-0 info: Active card count: 1. tveeprom 2-0050: Hauppauge model 74541, rev C6B6, serial# 3484150 tveeprom 2-0050: MAC address is 00-0D-FE-35-29-F6 tveeprom 2-0050: tuner model is Philips FM1236 MK5 (idx 116, type 43) tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 2-0050: audio processor is CX23418 (idx 38) tveeprom 2-0050: decoder processor is CX23418 (idx 31) tveeprom 2-0050: has radio cx18-0: Autodetected Hauppauge HVR-1600 cx18-0 info: NTSC tuner detected cx18-0: VBI is not yet supported cx18-0 info: Loaded module tuner cx18-0 info: Loaded module cs5345 cx18-0 i2c: i2c client register tuner 3-0043: chip found @ 0x86 (cx18 i2c driver #0-1) tda9887 3-0043: creating new instance tda9887 3-0043: tda988[5/6/7] found tuner 3-0061: chip found @ 0xc2 (cx18 i2c driver #0-1) cx18-0 i2c: i2c client register cs5345 2-004c: chip found @ 0x98 (cx18 i2c driver #0-0) tuner-simple 3-0061: creating new instance tuner-simple 3-0061: type set to 43 (Philips NTSC MK3 (FM1236MK3 or FM1236/F)) cx18-0 info: Allocate encoder MPEG stream: 63 x 32768 buffers (2016kB total) cx18-0 info: Allocate TS stream: 32 x 32768 buffers (1024kB total) cx18-0 info: Allocate encoder YUV stream: 16 x 131072 buffers (2048kB total) cx18-0 info: Allocate encoder PCM audio stream: 63 x 16384 buffers (1008kB total) cx18-0: Disabled encoder IDX device cx18-0: Registered device video1 for encoder MPEG (2 MB) DVB: registering new adapter (cx18) MXL5005S: Attached at address 0x63 DVB: registering adapter 0 frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)... cx18-0: DVB Frontend registered cx18-0: Registered device video33 for encoder YUV (2 MB) cx18-0: Registered device video25 for encoder PCM audio (1 MB) cx18-0: Registered device radio1 for encoder radio cx18-0: Initialized card #0: Hauppauge HVR-1600 cx18: End initialization firmware: requesting v4l-cx23418-apu.fw cx18-0 info: load segment a00000-a07fff cx18-0 info: load segment ae0000-ae00ff cx18-0 info: load segment b00000-b1a65f cx18-0: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes) firmware: requesting v4l-cx23418-cpu.fw cx18-0: loaded v4l-cx23418-cpu.fw firmware (158332 bytes) cx180 irq: SW1: 10000 SW2: 0 HW2: 0 cx18-0 info: 1 MiniMe Encoder Firmware 0.0.74.0 (Release 2007/03/12) cx18-0: FW version: 0.0.74.0 (Release 2007/03/12) firmware: requesting v4l-cx23418-apu.fw cx18-0 info: load segment a00000-a07fff cx18-0 info: load segment ae0000-ae00ff cx18-0 info: load segment b00000-b1a65f firmware: requesting v4l-cx23418-cpu.fw cx180 irq: SW1: 10000 SW2: 0 HW2: 0 cx18-0 info: 1 MiniMe Encoder Firmware 0.0.74.0 (Release 2007/03/12) cx18-0 info: Changing input from 1 to 0 cx18-0 info: Mute cx18-0 info: cmd 4008646f triggered fw load firmware: requesting v4l-cx23418-dig.fw cx18-0: loaded v4l-cx23418-dig.fw firmware (16382 bytes) cx18-0 info: decoder set video input 7, audio input 8 cx18-0 i2c: call_i2c_client addr=4c cx18-0 info: decoder set video input 7, audio input 8 cx18-0 api: CX18_APU_RESETAI cx18-0 api: mailbox error 200800ff for command CX18_APU_RESETAI cx18-0 info: Unmute cx18-0 info: Switching standard to 1000. cx18-0 info: changing video std to fmt 1 cx18-0 info: PLL regs = int: 15, frac: 2876158, post: 4 cx18-0 info: PLL = 0.000011 MHz cx18-0 info: PLL/8 = 0.000001 MHz cx18-0 info: ADC Sampling freq = 0.000001 MHz cx18-0 info: Chroma sub-carrier freq = 0.000000 MHz cx18-0 info: hblank 122, hactive 720, vblank 26 , vactive 487, vblank656 26, src_dec 543,burst 0x5b, luma_lpf 1, uv_lpf 1, comb 0x66, sc 0x087c1f cx18-0 info: Mute cx18-0 info: v4l2 ioctl: set frequency 1076 cx18-0 info: Unmute cx18-0 file: open encoder MPEG cx18-0: VIDIOC_QUERYCAP driver=cx18, card=Hauppauge HVR-1600, bus=PCI:0000:02:01.0, version=0x00010001, capabilities=0x01070001 cx18-0: VIDIOC_QUERYCAP driver=cx18, card=Hauppauge HVR-1600, bus=PCI:0000:02:01.0, version=0x00010001, capabilities=0x01070001 cx18-0: VIDIOC_ENUMINPUT index=0, name=Tuner 1, type=1, audioset=7, tuner=0, std=00001000, status=0 cx18-0: VIDIOC_ENUMINPUT index=1, name=S-Video 1, type=2, audioset=7, tuner=0, std=00ffffff, status=0 cx18-0: VIDIOC_ENUMINPUT index=2, name=Composite 1, type=2, audioset=7, tuner=0, std=00ffffff, status=0 cx18-0: VIDIOC_ENUMINPUT index=3, name=S-Video 2, type=2, audioset=7, tuner=0, std=00ffffff, status=0 cx18-0: VIDIOC_ENUMINPUT index=4, name=Composite 2, type=2, audioset=7, tuner=0, std=00ffffff, status=0 cx18-0: VIDIOC_ENUMINPUT error -22 cx18-0: VIDIOC_ENUM_FMT index=0, type=1, flags=0, pixelformat=HM12, description='HM12 (YUV 4:1:1)' cx18-0: VIDIOC_TRY_FMT type=vid-cap cx18-0: width=720, height=480, format=MPEG, field=interlaced, bytesperline=0 sizeimage=131072, colorspace=1 cx18-0 ioctl: close() of encoder MPEG cx18-0 file: open encoder PCM audio cx18-0: VIDIOC_QUERYCAP driver=cx18, card=Hauppauge HVR-1600, bus=PCI:0000:02:01.0, version=0x00010001, capabilities=0x01070001 cx18-0: VIDIOC_QUERYCAP driver=cx18, card=Hauppauge HVR-1600, bus=PCI:0000:02:01.0, version=0x00010001, capabilities=0x01070001 cx18-0: VIDIOC_ENUMINPUT index=0, name=Tuner 1, type=1, audioset=7, tuner=0, std=00001000, status=0 cx18-0: VIDIOC_ENUMINPUT index=1, name=S-Video 1, type=2, audioset=7, tuner=0, std=00ffffff, status=0 cx18-0: VIDIOC_ENUMINPUT index=2, name=Composite 1, type=2, audioset=7, tuner=0, std=00ffffff, status=0 cx18-0: VIDIOC_ENUMINPUT index=3, name=S-Video 2, type=2, audioset=7, tuner=0, std=00ffffff, status=0 cx18-0: VIDIOC_ENUMINPUT index=4, name=Composite 2, type=2, audioset=7, tuner=0, std=00ffffff, status=0 cx18-0: VIDIOC_ENUMINPUT error -22 cx18-0: VIDIOC_ENUM_FMT index=0, type=1, flags=0, pixelformat=HM12, description='HM12 (YUV 4:1:1)' cx18-0: VIDIOC_TRY_FMT type=vid-cap cx18-0: width=720, height=480, format=MPEG, field=interlaced, bytesperline=0 sizeimage=131072, colorspace=1 cx18-0 ioctl: close() of encoder PCM audio cx18-0 file: open encoder YUV cx18-0: VIDIOC_QUERYCAP driver=cx18, card=Hauppauge HVR-1600, bus=PCI:0000:02:01.0, version=0x00010001, capabilities=0x01070001 cx18-0: VIDIOC_QUERYCAP driver=cx18, card=Hauppauge HVR-1600, bus=PCI:0000:02:01.0, version=0x00010001, capabilities=0x01070001 cx18-0: VIDIOC_ENUMINPUT index=0, name=Tuner 1, type=1, audioset=7, tuner=0, std=00001000, status=0 cx18-0: VIDIOC_ENUMINPUT index=1, name=S-Video 1, type=2, audioset=7, tuner=0, std=00ffffff, status=0 cx18-0: VIDIOC_ENUMINPUT index=2, name=Composite 1, type=2, audioset=7, tuner=0, std=00ffffff, status=0 cx18-0: VIDIOC_ENUMINPUT index=3, name=S-Video 2, type=2, audioset=7, tuner=0, std=00ffffff, status=0 cx18-0: VIDIOC_ENUMINPUT index=4, name=Composite 2, type=2, audioset=7, tuner=0, std=00ffffff, status=0 cx18-0: VIDIOC_ENUMINPUT error -22 cx18-0: VIDIOC_ENUM_FMT index=0, type=1, flags=0, pixelformat=HM12, description='HM12 (YUV 4:1:1)' cx18-0: VIDIOC_TRY_FMT type=vid-cap cx18-0: width=720, height=480, format=HM12, field=interlaced, bytesperline=720 sizeimage=518400, colorspace=1 cx18-0 ioctl: close() of encoder YUV cx18-0 file: open encoder radio cx18-0 info: Mute cx18-0 i2c: call_i2c_client addr=4c cx18-0 info: decoder set video input 7, audio input 0 cx18-0 api: CX18_APU_RESETAI cx18-0 api: mailbox error 200800ff for command CX18_APU_RESETAI cx18-0 info: Unmute cx18-0: VIDIOC_QUERYCAP driver=cx18, card=Hauppauge HVR-1600, bus=PCI:0000:02:01.0, version=0x00010001, capabilities=0x01070001 cx18-0: VIDIOC_QUERYCAP driver=cx18, card=Hauppauge HVR-1600, bus=PCI:0000:02:01.0, version=0x00010001, capabilities=0x01070001 cx18-0: VIDIOC_ENUMINPUT index=0, name=Tuner 1, type=1, audioset=7, tuner=0, std=00001000, status=0 cx18-0: VIDIOC_ENUMINPUT index=1, name=S-Video 1, type=2, audioset=7, tuner=0, std=00ffffff, status=0 cx18-0: VIDIOC_ENUMINPUT index=2, name=Composite 1, type=2, audioset=7, tuner=0, std=00ffffff, status=0 cx18-0: VIDIOC_ENUMINPUT index=3, name=S-Video 2, type=2, audioset=7, tuner=0, std=00ffffff, status=0 cx18-0: VIDIOC_ENUMINPUT index=4, name=Composite 2, type=2, audioset=7, tuner=0, std=00ffffff, status=0 cx18-0: VIDIOC_ENUMINPUT error -22 cx18-0: VIDIOC_ENUM_FMT index=0, type=1, flags=0, pixelformat=HM12, description='HM12 (YUV 4:1:1)' cx18-0: VIDIOC_TRY_FMT type=vid-cap cx18-0: width=720, height=480, format=MPEG, field=interlaced, bytesperline=0 sizeimage=131072, colorspace=1 cx18-0 ioctl: close() of encoder radio cx18-0 info: Mute cx18-0 info: changing video std to fmt 1 cx18-0 info: PLL regs = int: 15, frac: 2876158, post: 4 cx18-0 info: PLL = 0.000011 MHz cx18-0 info: PLL/8 = 0.000001 MHz cx18-0 info: ADC Sampling freq = 0.000001 MHz cx18-0 info: Chroma sub-carrier freq = 0.000000 MHz cx18-0 info: hblank 122, hactive 720, vblank 26 , vactive 487, vblank656 26, src_dec 543,burst 0x5b, luma_lpf 1, uv_lpf 1, comb 0x66, sc 0x087c1f cx18-0 i2c: call_i2c_client addr=4c cx18-0 info: decoder set video input 7, audio input 8 cx18-0 api: CX18_APU_RESETAI cx18-0 api: mailbox error 200800ff for command CX18_APU_RESETAI cx18-0 info: Unmute It also displays the two lines below many times after I try to run "cat /dev/video1": cx18-0 info: ff DMA busy when it shouldn't cx180 irq: SW1: 10000 SW2: 0 HW2: 0 - Oystein Andy Walls wrote: > On Sat, 2008-10-25 at 20:24 -0400, Oystein Thorsen wrote: > >> I tried the mmio-fix version and it works like a charm... almost :-). >> The card now detects properly on boot. But the problem of getting no >> data is still there... >> >> I have not updated the driver in a few weeks and I could always try the >> latest version, but I'm not sure if the mmio fix is merged with the >> official version yet. Are there any other things I could try to get this >> working? I'm out of ideas (which is why I gave up on it for a few weeks >> :-) ). >> > > Use the latest v4l-dvb tree: > > http://linuxtv.org/hg/v4l-dvb/ > > > Don't bother with 'mmio_ndelay' (leave it at its default of '0'), and > leave the 'retry_mmio" parameter set to its default of '1'. > > The cx18 driver version should be v1.0.1, which has indicates > 'retry_mmio' is in effect by default. > > > Regards, > Andy > > >> Thanks for the help so far, >> >> - Oystein >> >> Andy Walls wrote: >> >>> On Tue, 2008-09-23 at 17:08 -0400, Oystein Thorsen wrote: >>> >>> >>>> It has taken me some time to respond to this because I have three >>>> different (wrong) outcomes when loading the driver and I can't figure >>>> out what the cause is, but I'll give you my guesses. I'll start with the >>>> one most similar to your suggestion; debug output when module loads, but >>>> no output. >>>> >>>> /proc/interrupts: >>>> CPU0 CPU1 >>>> 0: 194 0 IO-APIC-edge timer >>>> 21: 480319 0 IO-APIC-fasteoi cx18-0 >>>> >>>> >>> Hmm. The card is generating interrupts. That's good, but that means >>> you should be getting video data too, hmmm. >>> >>> >>> >>>> dmesg: >>>> cx18: Start initialization, version 1.0.0 >>>> cx18-0: Initializing card #0 >>>> cx18-0: Autodetected Hauppauge card >>>> cx18-0 info: base addr: 0xe8000000 >>>> cx18-0 info: Enabling pci device >>>> cx18-0 info: cx23418 (rev 0) at 02:01.0, irq: 21, latency: 64, memory: >>>> 0xe8000000 >>>> cx18-0 info: attempting ioremap at 0xe8000000 len 0x04000000 >>>> cx18-0: cx23418 revision 01010000 (B) >>>> cx18-0 info: GPIO initial dir: 0000cffe/0000ffff out: 00003001/00000000 >>>> cx18-0 info: activating i2c... >>>> cx18-0 i2c: i2c init >>>> cx18-0 info: Active card count: 1. >>>> tveeprom 1-0050: Hauppauge model 74541, rev C6B6, serial# 3484150 >>>> tveeprom 1-0050: MAC address is 00-0D-FE-35-29-F6 >>>> tveeprom 1-0050: tuner model is Philips FM1236 MK5 (idx 116, type 43) >>>> tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08) >>>> tveeprom 1-0050: audio processor is CX23418 (idx 38) >>>> tveeprom 1-0050: decoder processor is CX23418 (idx 31) >>>> tveeprom 1-0050: has radio >>>> cx18-0: Autodetected Hauppauge HVR-1600 >>>> cx18-0 info: NTSC tuner detected >>>> cx18-0: VBI is not yet supported >>>> cx18-0 info: Loaded module tuner >>>> cx18-0 info: Loaded module cs5345 >>>> cx18-0 i2c: i2c client register >>>> tuner 5-0043: chip found @ 0x86 (cx18 i2c driver #0-1) >>>> tda9887 5-0043: creating new instance >>>> tda9887 5-0043: tda988[5/6/7] found >>>> tuner 5-0061: chip found @ 0xc2 (cx18 i2c driver #0-1) >>>> cx18-0 i2c: i2c client register >>>> cs5345 1-004c: chip found @ 0x98 (cx18 i2c driver #0-0) >>>> tuner-simple 5-0061: creating new instance >>>> tuner-simple 5-0061: type set to 43 (Philips NTSC MK3 (FM1236MK3 or >>>> FM1236/F)) >>>> cx18-0 info: Allocate encoder MPEG stream: 63 x 8192 buffers (504kB total) >>>> cx18-0 info: Allocate TS stream: 63 x 8192 buffers (504kB total) >>>> cx18-0 info: Allocate encoder YUV stream: 8 x 131072 buffers (1024kB total) >>>> cx18-0 info: Allocate encoder PCM audio stream: 63 x 6144 buffers (378kB >>>> total) >>>> cx18-0: Disabled encoder IDX device >>>> cx18-0: Registered device video0 for encoder MPEG (63 x 8192 bytes) >>>> DVB: registering new adapter (cx18) >>>> MXL5005S: Attached at address 0x63 >>>> DVB: registering frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)... >>>> cx18-0: DVB Frontend registered >>>> cx18-0: Registered device video32 for encoder YUV (8 x 131072 bytes) >>>> cx18-0: Registered device video24 for encoder PCM audio (63 x 6144 bytes) >>>> cx18-0: Registered device radio0 for encoder radio >>>> cx18-0: Initialized card #0: Hauppauge HVR-1600 >>>> cx18: End initialization >>>> firmware: requesting v4l-cx23418-apu.fw >>>> cx18-0 info: load segment a00000-a07fff >>>> cx18-0 info: load segment ae0000-ae00ff >>>> cx18-0 info: load segment b00000-b1a65f >>>> cx18-0: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes) >>>> firmware: requesting v4l-cx23418-cpu.fw >>>> cx18-0: loaded v4l-cx23418-cpu.fw firmware (158332 bytes) >>>> cx18-0 info: 1 MiniMe Encoder Firmware 0.0.74.0 (Release 2007/03/12) >>>> cx18-0: FW version: 0.0.74.0 (Release 2007/03/12) >>>> firmware: requesting v4l-cx23418-apu.fw >>>> cx18-0 info: load segment a00000-a07fff >>>> cx18-0 info: load segment ae0000-ae00ff >>>> cx18-0 info: load segment b00000-b1a65f >>>> firmware: requesting v4l-cx23418-cpu.fw >>>> cx18-0 info: 1 MiniMe Encoder Firmware 0.0.74.0 (Release 2007/03/12) >>>> >>>> >>> All that looks good. It looks like you're using a recent change from my >>> ~awalls/v4l-dvb repository. Can you please use instead the latest from: >>> >>> http://linuxtv.org/hg/~awalls/cx18-mmio-fixes >>> >>> as this should get rid of the need for using mmio_ndelay and you also >>> then shouldn't have problems when unloading and reloading the module. >>> >>> >>> >>> >>> >>>> cx18-0 info: Changing input from 1 to 0 >>>> cx18-0 info: Mute >>>> cx18-0 info: cmd 4008646f triggered fw load >>>> firmware: requesting v4l-cx23418-dig.fw >>>> cx18-0: loaded v4l-cx23418-dig.fw firmware (16382 bytes) >>>> cx18-0 info: decoder set video input 7, audio input 8 >>>> cx18-0 i2c: call_i2c_client addr=4c >>>> cx18-0 info: decoder set video input 7, audio input 8 >>>> cx18-0 api: CX18_APU_RESETAI >>>> cx18-0 api: mailbox error 200800ff for command CX18_APU_RESETAI >>>> >>>> >>> I've seen errors like this when mmio_ndelay wasn't quite fixing things. >>> PLease try the repo I suggested above. >>> >>> >>> >>>> Also, when trying to capture video I get hundreds of these (in dmesg): >>>> cx18-0 info: ff DMA busy when it shouldn't >>>> >>>> After loading, unloading, uninstalling and installing a few times I got >>>> an error message (in dmesg) about increasing vmalloc (I haven't been >>>> able to reproduce this). But I thought I would try to increase the >>>> vmalloc space. >>>> >>>> >>> There's a memory leak when the driver fails to initialize a card. I >>> know where it is. I need to fix it. But you need not wait for that fix >>> (it doesn't leak memory, if the card initializes properly every >>> time). >>> >>> >>> >>>> Vmalloc space before: >>>> VmallocTotal: 110584 kB >>>> VmallocUsed: 96088 kB >>>> VmallocChunk: 9048 kB >>>> >>>> Vmalloc with 'vmalloc=256M': >>>> VmallocTotal: 241656 kB >>>> VmallocUsed: 37540 kB >>>> VmallocChunk: 199156 kB >>>> >>>> Now I'm unable to recognize the card (I stopped at mmio_ndelay=606). >>>> >>>> >>> That happens when the "mmio_ndelay" hack isn't effective (I found this >>> out on Saturday). The only way to recover is a hardware reset (e.g. >>> shutdown and reboot). >>> >>> >>> >>>> Usually the module would crash (making it impossible to unload the >>>> module) after loading/unloading the module once or twice (in addition >>>> to >>>> the load on boot). >>>> >>>> >>> The 'mmio_ndelay' hack obviously isn't working. Please try the >>> >>> http://linuxtv.org/hg/~awalls/cx18-mmio-fixes >>> >>> repo and let me know if it works for you. >>> >>> 'mmio_ndelay' was a rather passive method (give some idle time on the >>> bus) to attempt to get more reliable communication with the CX23418. >>> >>> the 'retry_mmio' parameter, enabled by default in the above repo >>> agressively checks and retries communications with the CX23418 to ensure >>> reliability. >>> >>> >>> Regards, >>> Andy >>> >>> >>> >>> >>>> Andy Walls wrote: >>>> >>>> >>>>> On Wed, 2008-09-17 at 22:13 -0400, Oystein Thorsen wrote: >>>>> >>>>> >>>>> >>>>>> Hi, >>>>>> I bought the HVR-1600 card about a week ago, but I've been unable to get >>>>>> it working on my mythtv server. I've tried it on a different computer >>>>>> where it worked in Vista. It also worked on Fedora 9 (same as the mythtv >>>>>> server) with the same drivers as on the mythtv server. I also have a >>>>>> PVR-150 card in the mythtv server from before. The PVR-150 been working >>>>>> the whole time while I've been playing around with the HVR-1600. >>>>>> >>>>>> I'm using the latest v4l-dvb drivers (from the official mercurial >>>>>> repository). >>>>>> >>>>>> Initially I had problems detecting the card, but it looks like the >>>>>> mmio_ndelay setting (152) corrected that: >>>>>> >>>>>> >>>>>> >>>>> All, >>>>> >>>>> I'm trying to figure out a good value for the driver to use as a default >>>>> for this parameter, so I can stop repeating the mmio_ndelay answer on >>>>> the list :) . I'm sure users expect the driver to "just work" out of >>>>> the box and I'd certainly like to make it that way. >>>>> >>>>> So far various people have reported that 91, 121, and 152 fix their >>>>> respective problems. So that means I'll need to check in a value of 152 >>>>> as a default. Has anyone else found they need to use a even higher >>>>> value for correct operation? >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>>> cx18-0: Initializing card #0 >>>>>> cx18-0: Autodetected Hauppauge card >>>>>> ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 21 (level, low) -> IRQ 21 >>>>>> cx18-0: cx23418 revision 01010000 (B) >>>>>> tveeprom 4-0050: Hauppauge model 74541, rev C6B6, serial# 3484150 >>>>>> tveeprom 4-0050: MAC address is 00-0D-FE-35-29-F6 >>>>>> tveeprom 4-0050: tuner model is Philips FM1236 MK5 (idx 116, type 43) >>>>>> tveeprom 4-0050: TV standards NTSC(M) (eeprom 0x08) >>>>>> tveeprom 4-0050: audio processor is CX23418 (idx 38) >>>>>> tveeprom 4-0050: decoder processor is CX23418 (idx 31) >>>>>> tveeprom 4-0050: has radio >>>>>> cx18-0: Autodetected Hauppauge HVR-1600 >>>>>> cx18-0: VBI is not yet supported >>>>>> tuner 5-0043: chip found @ 0x86 (cx18 i2c driver #0-1) >>>>>> tda9887 5-0043: creating new instance >>>>>> tda9887 5-0043: tda988[5/6/7] found >>>>>> tuner 5-0061: chip found @ 0xc2 (cx18 i2c driver #0-1) >>>>>> cs5345 4-004c: chip found @ 0x98 (cx18 i2c driver #0-0) >>>>>> tuner-simple 5-0061: creating new instance >>>>>> tuner-simple 5-0061: type set to 43 (Philips NTSC MK3 (FM1236MK3 or >>>>>> FM1236/F)) >>>>>> cx18-0: Disabled encoder IDX device >>>>>> cx18-0: Registered device video0 for encoder MPEG (2 MB) >>>>>> DVB: registering new adapter (cx18) >>>>>> firmware: requesting v4l-cx23418-apu.fw >>>>>> MXL5005S: Attached at address 0x63 >>>>>> DVB: registering frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)... >>>>>> cx18-0: DVB Frontend registered >>>>>> cx18-0: Registered device video32 for encoder YUV (2 MB) >>>>>> cx18-0: Registered device video24 for encoder PCM audio (1 MB) >>>>>> cx18-0: Registered device radio0 for encoder radio >>>>>> cx18-0: Initialized card #0: Hauppauge HVR-1600 >>>>>> cx18: End initialization >>>>>> cx18-0: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes) >>>>>> firmware: requesting v4l-cx23418-cpu.fw >>>>>> cx18-0: loaded v4l-cx23418-cpu.fw firmware (158332 bytes) >>>>>> cx18-0: FW version: 0.0.74.0 (Release 2007/03/12) >>>>>> firmware: requesting v4l-cx23418-apu.fw >>>>>> firmware: requesting v4l-cx23418-cpu.fw >>>>>> firmware: requesting v4l-cx23418-dig.fw >>>>>> cx18-0: loaded v4l-cx23418-dig.fw firmware (16382 bytes) >>>>>> >>>>>> When I try to capture some data (cat /dev/video0 > test.mpg) I get >>>>>> nothing (filesize is 0). The same happens if I try to record something >>>>>> on mythtv (The PVR-150 still records fine). >>>>>> >>>>>> Let me know if there is any other information that would be useful. >>>>>> >>>>>> >>>>>> >>>>> Look in /proc/interrupts and see what devices are sharing IRQ lines with >>>>> ivtv and cx18, and look in dmesg or /var/log/messages for any messages >>>>> about the kernel disabling/ignoring IRQ lines (i.e. "nobody cared"). >>>>> >>>>> >>>>> Use the cx18 debug module parameter to turn on Warning, Info, >>>>> Mailbox/API, and IRQ debug messages. See what gets logged especially >>>>> when you try to do a capture. If nothing jumps out at you, also turn on >>>>> the high volume debug flag. >>>>> >>>>> Regards, >>>>> Andy >>>>> >>>>> >>>>> >>>>> >>>>>> Thanks, >>>>>> >>>>>> Oystein Thorsen >>>>>> >>>>>> >>>>>> >>>>> _______________________________________________ >>>>> ivtv-users mailing list >>>>> [email protected] >>>>> http://ivtvdriver.org/mailman/listinfo/ivtv-users >>>>> >>>>> >>>>> >>>> Thanks for any feedback so far. >>>> >>>> _______________________________________________ >>>> ivtv-users mailing list >>>> [email protected] >>>> http://ivtvdriver.org/mailman/listinfo/ivtv-users >>>> >>>> >>>> >>> _______________________________________________ >>> ivtv-users mailing list >>> [email protected] >>> http://ivtvdriver.org/mailman/listinfo/ivtv-users >>> >>> >> _______________________________________________ >> ivtv-users mailing list >> [email protected] >> http://ivtvdriver.org/mailman/listinfo/ivtv-users >> >> > > > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users > _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
