Please do not top post. On Thu, Jan 1, 2009 at 15:34, stinky wizzleteet <[email protected]> wrote: > First, my Ubuntu Intrepid vanilla install (with my old mythconverg database) > gives me choppy sound and an offset image:
Mythtv is not very good for testing. Install the ivtv utilities which should be in the oficial ubuntu packages. make sure mythtv is not started and then: use ivtv-tune to tune to a channel/freqyency which has a signal. do cat /dev/video0 > test.mpg Does this create a correct file? > please check it out at: > http://www.box.net/shared/bt9kteod7l > > Tested Intrepid kernels are: > 2.6.27-7-generic > 2.6.28 built from git repository dec. 30 2008 I would stick with the oficial released versio from ubuntu. > Booted with kernel 2.6.28 dmesg gives me: > > [79437.395660] ivtv: Start initialization, version 1.4.0 > [79437.395883] ivtv0: Initializing card #0 > [79437.395888] ivtv0: Autodetected Hauppauge card (cx23416 based) > [79437.399054] vendor=8086 device=244e > [79437.399064] ivtv 0000:02:0c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 > [79437.452721] tveeprom 0-0050: Hauppauge model 32054, rev B148, serial# > 7160374 > [79437.452725] tveeprom 0-0050: tuner model is LG TP18PSB11D (idx 48, type > 29) > [79437.452729] tveeprom 0-0050: TV standards PAL(B/G) (eeprom 0x04) > [79437.452732] tveeprom 0-0050: audio processor is MSP4418 (idx 25) > [79437.452735] tveeprom 0-0050: decoder processor is SAA7115 (idx 19) > [79437.452738] tveeprom 0-0050: has no radio, has IR receiver, has no IR > transmi > tter > [79437.452742] ivtv0: Autodetected Hauppauge WinTV PVR-250 > [79437.530479] saa7115 0-0021: saa7115 found (1f7115d0e100000) @ 0x42 (ivtv > i2c > driver #0) > [79437.663399] msp3400 0-0040: MSP4418G-A2 found @ 0x80 (ivtv i2c driver #0) > [79437.663402] msp3400 0-0040: msp3400 supports nicam and radio, mode is > autodet > ect and autoselect > [79437.702796] tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) > [79437.703385] tuner-simple 0-0061: creating new instance > [79437.703389] tuner-simple 0-0061: type set to 29 (LG PAL_BG (TPI8PSB11D)) > [79437.704935] ivtv0: Registered device video0 for encoder MPG (4096 kB) > [79437.704982] ivtv0: Registered device video32 for encoder YUV (2048 kB) > [79437.705025] ivtv0: Registered device vbi0 for encoder VBI (1024 kB) > [79437.705068] ivtv0: Registered device video24 for encoder PCM (320 kB) > [79437.705072] ivtv0: Initialized card #0: Hauppauge WinTV PVR-250 > [79437.705101] ivtv: End initialization > [79438.448018] ivtv 0000:02:0c.0: firmware: requesting v4l-cx2341x-enc.fw > [79438.518496] ivtv0: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes) > [79438.716153] ivtv0: Encoder revision: 0x02060039 > > I see nothing out of the ordinary with this, in the past (v 0.4 I believe) I > had to specify a different tuner, tried that, but no effect whatsoever. You should not need to specify a different tuner with this kenel version. > Secondly, I tried to fix this by building ivtv-utils myself, but the build > breaks because of a conflicting ivtv.h in both /usr/include/linux and > /usr/src/linux/include/linux Why do you need to build them? They should be available from ubuntu. > Also, v4l-dvb-9d9288bed20b breaks on building bttv, but for a different > reason I suspect. That is the risk of using the bleeding edge repo from v4l-dvb. Greets Sander _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
