Thanks, I tried the older changeset, and seemed to get a little further. Here is the result:
dmesg |grep cx18 cx18: Start initialization, version 1.3.0 cx18-0: Initializing card 0 cx18-0: Autodetected Hauppauge card cx18 0000:03:05.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 cx18-0: cx23418 revision 01010000 (B) cx18-0: Autodetected Hauppauge HVR-1600 cx18-0: Simultaneous Digital and Analog TV capture supported IRQ 20/cx18-0: IRQF_DISABLED is not guaranteed on shared IRQs tuner 1-0061: chip found @ 0xc2 (cx18 i2c driver #0-1) cs5345 0-004c: chip found @ 0x98 (cx18 i2c driver #0-0) cx18-0: Registered device video0 for encoder MPEG (64 x 32.00 kB) DVB: registering new adapter (cx18) cx18-0: DVB Frontend registered cx18-0: Registered DVB adapter0 for TS (32 x 32.00 kB) cx18-0: Registered device video32 for encoder YUV (20 x 101.25 kB) cx18-0: Registered device vbi0 for encoder VBI (20 x 51984 bytes) cx18-0: Registered device video24 for encoder PCM audio (256 x 4.00 kB) cx18-0: Initialized card: Hauppauge HVR-1600 cx18: End initialization cx18 0000:03:05.0: firmware: requesting v4l-cx23418-cpu.fw cx18-0: Unable to open firmware v4l-cx23418-cpu.fw cx18-0: Did you put the firmware in the hotplug firmware directory? cx18-0: Retry loading firmware cx18 0000:03:05.0: firmware: requesting v4l-cx23418-cpu.fw cx18-0: Unable to open firmware v4l-cx23418-cpu.fw cx18-0: Did you put the firmware in the hotplug firmware directory? cx18-0: Failed to initialize on vbi0 cx18-0: Failed to initialize on video0 cx18-0: Failed to initialize on video24 cx18-0: Failed to initialize on video32 cx18-0: Failed to initialize on video0 cx18-0: Failed to initialize on video0 cx18-0: Failed to initialize on video0 cx18-0: Failed to initialize on video0 cx18-0: Failed to initialize on video0 cx18-0: Failed to initialize on video0 cx18-0: Failed to initialize on video0 cx18-0: Failed to initialize on video0 cx18-0: Failed to initialize on video0 cx18-0: Failed to initialize firmware starting DVB feed cx18-0: Failed to initialize firmware starting DVB feed cx18-0: Failed to initialize firmware starting DVB feed cx18-0: Failed to initialize firmware starting DVB feed cx18-0: Failed to initialize firmware starting DVB feed cx18-0: Failed to initialize firmware starting DVB feed cx18-0: Failed to initialize firmware starting DVB feed cx18-0: Failed to initialize firmware starting DVB feed cx18-0: Failed to initialize firmware starting DVB feed cx18-0: Failed to initialize on video0 cx18-0: Failed to initialize on video0 cx18-0: Failed to initialize on video0 cx18-0: Failed to initialize on video0 Not sure where to go from here? On Sat, May 22, 2010 at 12:58 PM, faginbagin <[email protected]> wrote: > > > Andy Walls wrote: >> >> On Sat, 2010-05-22 at 11:17 -0400, J McBride wrote: >>> >>> I have attempted to get a Hauppauge HTV-1600 card working in >>> SimpyMepis. I have generally followed the steps in the following >>> how-to guides: >>> >>> >>> >>> http://www.linuxtv.org/wiki/index.php/How_to_Obtain,_Build_and_Install_V4L-DVB_Device_Drivers >>> and >>> http://ivtvdriver.org/index.php/Howto:Debian >>> >>> >>> I had to run "make config" and not configure the FireTV due to a >>> compilation error, then all seemed to work well until the command: >>> #modprobe cx18 >>> >>> >>> which resulted in the error: >>> >>> FATAL: Error inserting cx18 >>> >>> (/lib/modules/2.6.32-1-mepis64-smp/kernel/drivers/media/video/cx18/cx18.ko): >>> Unknown symbol in module, or unknown parameter (see dmesg) >>> >>> >>> Then I did: >>> >>> >>> dmesg |grep cx18 >>> cx18: Unknown symbol ir_codes_hauppauge_new_table >>> >>> >>> So, I am at my limit here. I cannot find any similar errors through >>> google. Any suggestions on how I get this to work? >> >> Please report this to the [email protected] list. There has >> been recent IR churn that you're running into. >> >> I'll try to respond later today, but life's busy. Odd's are there are >> some new IR modeuls that didn't get built. >> >> Regards, >> Andy >> >> >> >> >> _______________________________________________ >> ivtv-users mailing list >> [email protected] >> http://ivtvdriver.org/mailman/listinfo/ivtv-users > > If you're impatient, you might want to try an older changeset. I've been > using this one from 12/7/09 and have been happy with it: > http://linuxtv.org/hg/v4l-dvb/archive/065f9e34e07b.tar.bz2 > > HTH, > Helen > > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users > _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
