Hi all,
I recently put a Hauppauge HVR-1600 model 1388 (p/n 74351) into my Fedora 14
machine (kernel 2.6.35.13-91.fc14.x86_64). It works fine under Windows 7 but
won't
initialize under Linux, and /dev/video0 doesn't get created. dmesg says:
[ 17.851163] cx18: Start initialization, version 1.4.0
[ 17.856437] cx18-0: Initializing card 0
[ 17.861665] cx18-0: Autodetected Hauppauge card
[ 17.866992] alloc irq_desc for 21 on node 0
[ 17.866994] alloc kstat_irqs on node 0
[ 17.867014] cx18 0000:04:07.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 17.872239] cx18-0: Unreasonably low latency timer, setting to 64 (was 32)
[ 17.882716] cx18-0: cx23418 revision 01010000 (B)
[ 17.888235] alloc irq_desc for 16 on node 0
[ 17.888236] alloc kstat_irqs on node 0
...unrelated stuff deleted...
[ 18.123131] tveeprom 0-0050: Hauppauge model 74351, rev F1F5, serial# XXXXXXX
[ 18.128960] tveeprom 0-0050: MAC address is XX:XX:XX:XX:XX:XX
[ 18.134815] tveeprom 0-0050: tuner model is NXP 18271C2 (idx 155, type 54)
[ 18.140776] tveeprom 0-0050: TV standards PAL(B/G) NTSC(M) PAL(I)
SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)
[ 18.146976] tveeprom 0-0050: audio processor is CX23418 (idx 38)
[ 18.153244] tveeprom 0-0050: decoder processor is CX23418 (idx 31)
[ 18.159462] tveeprom 0-0050: has no radio
[ 18.165605] cx18-0: Autodetected Hauppauge HVR-1600
[ 18.171759] cx18-0: Simultaneous Digital and Analog TV capture supported
[ 18.305638] cs5345 0-004c: chip found @ 0x98 (cx18 i2c driver #0-0)
[ 18.318009] cx18-0: Registered device video0 for encoder MPEG (64 x 32.00 kB)
[ 18.324025] DVB: registering new adapter (cx18)
[ 18.362198] cx18-0: frontend initialization failed
[ 18.368189] cx18-0: DVB failed to register
[ 18.374081] cx18-0: Registered device video32 for encoder YUV (20 x 101.25
kB)
[ 18.380034] cx18-0: Registered device vbi0 for encoder VBI (20 x 51984 bytes)
[ 18.385956] cx18-0: Registered device video24 for encoder PCM audio (256 x
4.00 kB)
[ 18.391899] cx18-0: unregister DVB
[ 18.397944] cx18-0: Error -1 registering devices
[ 18.406194] cx18-0: Error -1 on initialization
[ 18.411999] cx18: probe of 0000:04:07.0 failed with error -1
[ 18.417802] cx18: End initialization
(Card s/n and system MAC address replaced by "XX")
I've got the firmware provided with Fedora: cx18-firmware-20080628-3.noarch
and the driver from ATrpms:
video4linux-kmdl-2.6.35.13-91.fc14-20110208_132512-98.fc14.x86_64
Are these new enough to support this card, or should I get the ones from:
http://linuxtv.org/wiki/index.php/How_to_Obtain,_Build_and_Install_V4L-DVB_Device_Drivers
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
