On 07/01/2005 Michael T. Dean wrote:
> One or more modules is failing to load. It seems there's a problem with
> your tveeprom module--which may be caused by manually loading the module.
i've also tried to load ivtv directly, what caused several other modules
to be loaded, namely i2c_core, i2c_algo_bit, tveeprom, tuner, saa7115,
saa7127 and msp3400.
> Make sure your mod{ules,probe}.conf contains only:
>
> # ivtv modules setup
> alias char-major-81 videodev
> alias char-major-81-0 ivtv
ok, up to now these conffiles had
alias char-major-81 bttv
i changed this now to your two lines.
afterwards i tested you command:
> and if you want to load the ivtv framebuffer when you load ivtv,
>
> install ivtv /sbin/modprobe --ignore-install ivtv; /sbin/modprobe ivtv-fb
>
> And then use *only* "modprobe ivtv" (do not insmod) to load the driver.
# install ivtv /sbin/modprobe --ignore-install ivtv; /sbin/modprobe
# ivtv-fb
install: unrecognized option `--ignore-install'
Try `install --help' for more information.
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.2.0 (rc3b) loading
ivtv: Linux version: 2.6.9-amd64 preempt gcc-3.3
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Autodetected WinTV PVR 350 card
ivtv: Found an iTVC15 based chip
ACPI: PCI interrupt 0000:00:07.0[A] -> GSI 18 (level, low) -> IRQ 18
ivtv: VIA PCI device: 0x3188 vendor: 0x1106
tveeprom: Hauppauge: model = 48139, rev = K257, serial# = 7672850
tveeprom: tuner = Philips FM1216 ME MK3 (idx = 57, type = 38)
tveeprom: tuner fmt = PAL(D/K) (eeprom = 0x74, v4l2 = 0x00400e17)
tveeprom: audio_processor = CS5331 (type = 9)
ivtv: i2c attach [client=tveeprom[0],ok]
ivtv: Tuner Type 38, Tuner formats 0x00400e17, Radio: yes, Model 0x00ad2557,
Revision 0x00000001
ivtv: PAL tuner detected
ivtv: SECAM tuner detected
ivtv: Radio detected
tuner: Ignoring new-style parameters in presence of obsolete ones
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv: i2c attach [client=(tuner unset),ok]
saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
saa7115: detecting saa7115 client on address 0x42
saa7115: writing init values
ivtv: i2c attach [client=saa7115[0],ok]
saa7115: status: (1E) 0x40, (1F) 0xc0
saa7127: video encoder driver version V 0.3 loaded
saa7127: Selecting NTSC video Standard
saa7127: Selecting S-Video+Composite
saa7127: Turn WSS off
saa7127: Widescreen Mode 4:3 Full Format
saa7127: Selecting Normal Encoder Input
saa7127: Enable Video Output
ivtv: i2c attach [client=saa7127[0],ok]
msp34xx: ivtv version
msp34xx: init: chip=MSP3418W-B3, has NICAM support, simple (D) mode,
simpler (G) no-thread mode
msp34xx: $Id$ compiled on: Jan 6 2005 15:59:46
ivtv: i2c attach [client=MSP3418W-B3,ok]
ivtv: Encoder revision: 0x02050032
ivtv: Encoder Firmware is buggy, use version 0x02040011
ivtv: Decoder revision: 0x02020023
ivtv: Configuring WinTV PVR 350 card with 9 streams
ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes total
ivtv: Registered v4l2 device, streamtype 0 minor 0
ivtv: Create DMA stream 1
ivtv: Registered v4l2 device, streamtype 1 minor 32
ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 2 minor 224
ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 3 minor 24
ivtv: Create stream 4
ivtv: Registered v4l2 device, streamtype 4 minor 64
ivtv: Create DMA stream 5 using 16 65536 byte buffers 1048576 kbytes total
ivtv: Registered v4l2 device, streamtype 5 minor 16
ivtv: Create stream 6 using 1024 2048 byte buffers 262144 kbytes total
ivtv: Registered v4l2 device, streamtype 6 minor 228
ivtv: Create stream 7
ivtv: Registered v4l2 device, streamtype 7 minor 232
ivtv: Create DMA stream 8
ivtv: Registered v4l2 device, streamtype 8 minor 48
ivtv: Setting Tuner 38
ivtv: ivtv_enc_thread: pid = 5441, itv = 0xffffffffa00491a0
ivtv: ivtv_dec_thread: pid = 5442, itv = 0xffffffffa00491a0
tuner: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) by ivtv i2c
driver #0
ivtv: Setting audio matrix to input 3, output 1
ivtv: Switching standard to PAL.
saa7115: decoder set norm PAL
saa7115: set audio: 0x01
saa7127: Setting Encoder Video Standard
saa7127: Set PAL Video Mode
saa7127: Selecting PAL video Standard
ivtv: Initialized WinTV PVR 350, card #0
ivtv: ==================== END INIT IVTV ====================
ivtv-osd: Framebuffer module loaded (attached to ivtv card id 0)
ivtv-osd: Framebuffer is at decoder-relative address 0x00510000 and has 1704960
bytes.
ivtv-osd: screen coords: [0 0] -> [720 576]
ivtv-osd: original global alpha = 208
ivtv-osd: current OSD state = 39
ivtv-osd: new global alpha = 208 (1 255 0)
ivtv-osd: framebuffer at 0xc9510000, mapped to 0xffffff0003010000, size 1620k
ivtv-osd: mode is 720x576x32, linelength=2880
ivtv-osd: fb2: iTVC15 TV out frame buffer device
anyway, the test command 'cat /dev/video0 > my.mpg' still crashes my
whole system. it gives endless output, but it's to fast to read and not
possible to restore, as machine needs to be rebooted immediately.
is there a possibility, that kernel 2.6.10 and ivtv 0.3.2a do better
work?
bye
jonas
-------------------------------------------------------
The SF.Net email is sponsored by: Beat the post-holiday blues
Get a FREE limited edition SourceForge.net t-shirt from ThinkGeek.
It's fun and FREE -- well, almost....http://www.thinkgeek.com/sfshirt
_______________________________________________
Ivtv-users mailing list
Ivtv-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/ivtv-users
