anyone on the mytv mailing list will not doubt have seen me with this problem but its doing my head in...
I've got an
ASRock motherboard
512mb RAM
Soundblaster Live
40GB IDE HD
and 2 PVR 250's....
I run mythtv 0.17 under FC3 following jarrods guide.
I've tried every bit of advice available with no avail so i thought i'd ask you guys.
Every 40 minutes or so (often when recording but not always) my box just freezes solid normally with a high piched tone coming through my speakers. I can't ssh in and only a hard reboot restores it.
I've got a few ideas as to why my this may be occuring, but haven't had time to test them out, I just wondered if anyone else had had the same problem.
I've had a problem with one cards sound quality, which was having distortion problems, but I found a link
http://www.shspvr.com/forum/viewtopic.php?t=5241&postdays=0&postorder=asc&highlight=pvr%20250%20sound&start=30
that told me to put a fan on the card which I did and it solved my sound problems, but this may indicate a dodgy card.
It may be a irq problem, here's my cat /proc/interrupts(the bit that matters):
10: 38276 XT-PIC EMU10K1, ivtv0, uhci_hcd
11: 60790 XT-PIC eth0, ivtv1, uhci_hcd, nvidia
I thought it may be a APIC, ACPI etc problem but I've turned all that off(as far as i know) and still no joy.
I've tried ssh'ing in and 'tail -f' on /var/log/mythtv/mythbackend.log and /var/messages but neither print anything at all when a crash occurs so they're of no use whatsoever
I've attached my dmesg, file for further reading Any ideas please it really getting on my nerves. Thanks Tom
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
Built 1 zonelists
Kernel command line: ro root=LABEL=/ rhgb quiet acpi=off apic=off apic=no
apm=off pci=routeirq
Initializing CPU#0
CPU 0 irqstacks, hard=c03d3000 soft=c03d2000
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1666.562 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 514876k/524224k available (2045k kernel code, 8752k reserved, 655k
data, 160k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3268.60 BogoMIPS (lpj=1634304)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383f3ff c1cbfbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Sempron(tm) 2400+ stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 568k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfdae1, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20041105
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: ACPI disable
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Via IRQ fixup
PCI: Using IRQ router default [1106/3177] at 0000:00:11.0
PCI: IRQ 0 for device 0000:00:11.1 doesn't match PIRQ mask - try pci=usepirqmask
PCI: Hardcoded IRQ 14 for device 0000:00:11.1
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1111001002.690:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key C1F2FA57F7EECD64
- User ID: Red Hat, Inc. (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 64M @ 0xe0000000
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 76 ports, IRQ sharing enabled
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
PCI: Hardcoded IRQ 14 for device 0000:00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: SAMSUNG SP0411N, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: LG DVD-ROM DRD-8160B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 78242976 sectors (40060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(133)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4 < hda5 >
hdc: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 9362)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 160k freed
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
floppy0: no floppy controllers found
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
divert: allocating divert_blk for eth0
eth0: VIA Rhine II at 0xdffffe00, 00:0b:6a:6f:11:47, IRQ 11.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
ip_tables: (C) 2000-2002 Netfilter core team
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Linux video capture interface: v1.00
ivtv: no version for "struct_module" found: kernel tainted.
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.2.0 (rc3g) loading
ivtv: Linux version: 2.6.10-1.770_FC3 686 REGPARM 4KSTACKS gcc-3.4
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Autodetected WinTV PVR 250 card
ivtv: Found an iTVC16 based chip
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
ivtv: VIA PCI device: 0x3189 vendor: 0x1106
tveeprom: Hauppauge: model = 32035, rev = B135, serial# = 6916180
tveeprom: tuner = Temic 4066FY5 (idx = 35, type = 18)
tveeprom: tuner fmt = PAL(I) (eeprom = 0x10, v4l2 = 0x00000010)
tveeprom: audio_processor = MSP3415 (type = 6)
ivtv: i2c attach [client=tveeprom[0],ok]
ivtv: Tuner Type 18, Tuner formats 0x00000010, Radio: yes, Model 0x008914d5,
Revision 0x00000000
ivtv: PAL tuner detected
ivtv: Radio detected
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv: i2c attach [client=(tuner unset),ok]
saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
saa7115: detecting saa7115 client on address 0x42
saa7115: writing init values
ivtv: i2c attach [client=saa7115[0],ok]
saa7115: status: (1E) 0x48, (1F) 0xc0
msp34xx: init: chip=MSP3415G-B8 +nicam +simple +simpler +radio mode=simple
ivtv: i2c attach [client=MSP3415G-B8,ok]
msp3410: daemon started
ivtv: Encoder revision: 0x02040024
ivtv: Encoder Firmware is buggy, use version 0x02040011
ivtv: Configuring WinTV PVR 250 card with 5 streams
ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes total
ivtv: Registered v4l2 device, streamtype 0 minor 0
ivtv: Create DMA stream 1
ivtv: Registered v4l2 device, streamtype 1 minor 32
ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 2 minor 224
ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 3 minor 24
ivtv: Create stream 4
ivtv: Registered v4l2 device, streamtype 4 minor 64
ivtv: Setting Tuner 18
tuner: type set to 18 (Temic PAL_I (4066 FY5)) by ivtv i2c driver #0
ivtv: Setting audio matrix to input 3, output 1
ivtv: Switching standard to PAL.
saa7115: decoder set norm PAL
saa7115: set audio: 0x01
ivtv: Initialized WinTV PVR 250, card #0
ivtv: Autodetected WinTV PVR 250 card
ivtv: Found an iTVC16 based chip
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
ivtv: VIA PCI device: 0x3189 vendor: 0x1106
tveeprom: Hauppauge: model = 32035, rev = B135, serial# = 6916325
tveeprom: tuner = Temic 4066FY5 (idx = 35, type = 18)
tveeprom: tuner fmt = PAL(I) (eeprom = 0x10, v4l2 = 0x00000010)
tveeprom: audio_processor = MSP3415 (type = 6)
ivtv: i2c attach [client=tveeprom[1],ok]
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1
ivtv: i2c attach [client=(tuner unset),ok]
saa7115: starting probe for adapter ivtv i2c driver #1 (0x10005)
saa7115: detecting saa7115 client on address 0x42
saa7115: writing init values
ivtv: i2c attach [client=saa7115[1],ok]
ivtv: ivtv_enc_thread: pid = 2460, itv = 0xe0a05020
saa7115: status: (1E) 0x48, (1F) 0xc0
msp34xx: init: chip=MSP3415G-B8 +nicam +simple +simpler +radio mode=simple
ivtv: i2c attach [client=MSP3415G-B8,ok]
msp3410: daemon started
ivtv: Tuner Type 18, Tuner formats 0x00000010, Radio: yes, Model 0x008914d5,
Revision 0x00000000
ivtv: PAL tuner detected
ivtv: Radio detected
ivtv: Encoder revision: 0x02040024
ivtv: Encoder Firmware is buggy, use version 0x02040011
ivtv: Configuring WinTV PVR 250 card with 5 streams
ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes total
ivtv: Registered v4l2 device, streamtype 0 minor 1
ivtv: Create DMA stream 1
ivtv: Registered v4l2 device, streamtype 1 minor 33
ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 2 minor 225
ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 3 minor 25
ivtv: Create stream 4
ivtv: Registered v4l2 device, streamtype 4 minor 65
ivtv: Setting Tuner 18
tuner: type set to 18 (Temic PAL_I (4066 FY5)) by ivtv i2c driver #1
ivtv: Setting audio matrix to input 3, output 1
ivtv: Switching standard to PAL.
saa7115: decoder set norm PAL
saa7115: set audio: 0x01
ivtv: Initialized WinTV PVR 250, card #1
ivtv: ==================== END INIT IVTV ====================
ivtv: ivtv_enc_thread: pid = 2553, itv = 0xe0a194c0
lirc_dev: IR Remote Control driver registered, at major 61
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
lirc_i2c: chip found @ 0x18 (Hauppauge IR)
ivtv: i2c attach [client=Hauppauge IR,ok]
lirc_dev: lirc_register_plugin:sample_rate: 10
lirc_i2c: chip found @ 0x18 (Hauppauge IR)
ivtv: i2c attach [client=Hauppauge IR,ok]
lirc_dev: lirc_register_plugin:sample_rate: 10
saa7115: starting probe for adapter SMBus Via Pro adapter at 0400 (0x0)
gameport: pci0000:00:0d.1 speed 1193 kHz
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: irq 12, pci mem 0xdfffff00
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.3: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: irq 11, io base 0xdc00
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: irq 10, io base 0xe000
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: irq 3, io base 0xe400
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03697c0(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
nvidia: module license 'NVIDIA' taints kernel.
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7167 Fri Feb 25
09:08:22 PST 2005
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
spurious 8259A interrupt: IRQ7.
eth0: no IPv6 routers present
EXT3 FS on hda2, internal journal
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: [EMAIL PROTECTED]
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54
ide: failed opcode was 100
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 2f 90 a0 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 12468864
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SGI XFS with ACLs, security attributes, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
XFS mounting filesystem hda5
Starting XFS recovery on filesystem: hda5 (dev: hda5)
Ending XFS recovery on filesystem: hda5 (dev: hda5)
Adding 522104k swap on /dev/hda3. Priority:-1 extents:1
ieee1394: Initialized config rom entry `ip1394'
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
lp: driver loaded but no devices found
saa7115: decoder set picture bright=128 contrast=63 saturation=64 hue=0
saa7115: decoder set picture bright=128 contrast=63 saturation=63 hue=0
saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0
saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0
saa7115: decoder disable output
saa7115: decoder enable output
saa7115: decoder set picture bright=128 contrast=63 saturation=64 hue=0
saa7115: decoder set picture bright=128 contrast=63 saturation=63 hue=0
saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0
saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0
saa7115: decoder disable output
saa7115: decoder enable output
saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0
saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0
saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0
saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0
saa7115: decoder set size
saa7115: decoder disable output
saa7115: decoder enable output
application mythfrontend uses obsolete OSS audio interface
saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0
saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0
saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0
saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0
saa7115: decoder disable output
saa7115: decoder enable output
saa7115: decoder disable output
saa7115: decoder enable output
