Yes, it will but... something like Arduino Pro (without FTDI)... or with FTDI included... for anyone, skilled or not :P ... I just saw that there still are PCs with serial comm: http://www.stealth.com/littlepc_100_ultraminipc.htm
Vasi(funlw65) On Aug 6, 11:27 am, Sebastien Lelong <[email protected]> wrote: > 25K22 (and 26K22 IIRC) doesn't provide USB peripheral, won't it be a problem > for you ? > > Cheers, > Seb > > 2010/8/5 funlw65 <[email protected]> > > > > > Yes, that was first thought - using your board... but it must be a > > board which use a 25k22, 26k22 to be possible... an Arduino clone > > using your exact mapping... > > > On Aug 5, 10:32 pm, Sebastien Lelong <[email protected]> > > wrote: > > > Sorry, I don't understand what you're try to do :) Do you want to put an > > > Atmega on Freejalduino ?? > > > > 2010/8/5 funlw65 <[email protected]> > > > > > Now, you gave me some food for thought with your conversion... > > > > unfortunately, an ATmega328p does not fit into my board... only if we > > > > have a similar board (Arduino clone), using 25k22, 26k22... so, first > > > > must be the chicken... to lay the eggs... > > > > > Vasi(funlw65) > > > > > On Aug 5, 3:56 pm, Sebastien Lelong <[email protected]> > > > > wrote: > > > > > Hi guys, > > > > > > I tried to design Cuckoo PCB, attached are Eagle files and screenshot > > for > > > > > bottom and top layers. Most traces are 16mil width, sometime 14mil to > > > > pass > > > > > between holes, and 5V/GND traces are 20mil. > > > > > > This is a double-sided PCB, aimed to be plugged upside down: bottom > > side, > > > > > where Cuckoo drawing is visible, is the one that can be viewed when > > > > plugged > > > > > on Arduino. PIC, and most components will be hidden by the board. In > > my > > > > > "reckoning" is correct, components should fit appropriately between > > > > Atmega > > > > > chipset, Xtal, push button and shield connectors. Maybe... > > > > > > Subsidiary question: in Eagle, I manually route traces, and added > > > > ratsness > > > > > rectangle. I wanted to check if no unrouted traces were remaining (I > > know > > > > > there weren't but...), and Eagle started to create new signals, with > > very > > > > > little traces and vias. There weren't connected to any existing > > signals, > > > > > it's as though it was to "cut" ratsness rectangle. I've removed them. > > > > Does > > > > > anyone know what's the purpose of such added traces/signals ? > > > > > > As reply to you, Sir Vasile Surducan: > > > > > > 2010/7/24 vasile surducan <[email protected]> > > > > > > > We had a looong discussion about ICSP some time ago, so this is the > > > > last > > > > > > time I'm opening again my mouth (by writting) about this subject. > > > > > > Put a 47nF... 100nF capacitor in parallel with your reset switch, > > in > > > > that > > > > > > way when turn ON the power supply, reset will be automatically, > > change > > > > R1 > > > > > > from 1k2 to 10k...33k and take out that diode. > > > > > > See for reference (only if consider those above) this one: > > >http://4.bp.blogspot.com/_0iJadzFlwNo/S_OgtycPtxI/AAAAAAAAAAc/vNesIW3. > > > > .. > > > > > > Due to lack of space, I've removed reset switch. About reset > > resistor, > > > > > Arduino already has one, 10K, connected from RESET /MCLR to +5V. If I > > had > > > > > added another resistor on Cuckoo board, both resistors would have > > been in > > > > > parallel, resulting in a "not so good value I guess". So, I've made > > > > cuckoo > > > > > reset resistor optional (for standalone usage, not connected to > > Arduino), > > > > > and let MCLR connected to Arduino reset circuitry (that is 10K). > > > > > > Diode was removed. > > > > > > > < > > > >http://4.bp.blogspot.com/_0iJadzFlwNo/S_OgtycPtxI/AAAAAAAAAAc/vNesIW3.. > > > > .>Switching > > > > > > the clock through a switch is a very bad idea. Very long routes of > > > > clock > > > > > > (incuding connectors in their path) is also a bad idea. > > > > > > Connecting to Arduino Xtal is now optional. By default, internal > > clock > > > > will > > > > > be recommanded (16MHz, same MIPS in the end). > > > > > > > If you want to start a merchantable new arduino, imagine the puzzle > > > > game > > > > > > (on a surface and not a startrek spatial puzzle) and imagine a > > complete > > > > > > jalluino-picolino (including "shields" ) in that way. Picolino = > > very > > > > small > > > > > > Sure, how do we proceed ? > > > > > > I think I'll try to build it with some cardboard, to check if all > > > > components > > > > > fit well. Then I plan to order PCBs from Seeedstudio prototyping > > > > service... > > > > > > Cheers, > > > > > Seb > > > > > > cuckoo_pcb_top.png > > > > > 360KViewDownload > > > > > > cuckoo_pcb_bottom.png > > > > > 367KViewDownload > > > > > > cuckoo.sch > > > > > 228KViewDownload > > > > > > cuckoo.brd > > > > > 66KViewDownload > > > > > > cuckoo_sch.png > > > > > 28KViewDownload > > > > > -- > > > > You received this message because you are subscribed to the Google > > Groups > > > > "jallib" group. > > > > To post to this group, send email to [email protected]. > > > > To unsubscribe from this group, send email to > > > > [email protected]<jallib%[email protected]> > > <jallib%[email protected]<jallib%[email protected]> > > > > > . > > > > For more options, visit this group at > > > >http://groups.google.com/group/jallib?hl=en. > > > > -- > > > Sébastien Lelonghttp://www.sirloon.nethttp://sirbot.org > > > -- > > You received this message because you are subscribed to the Google Groups > > "jallib" group. > > To post to this group, send email to [email protected]. > > To unsubscribe from this group, send email to > > [email protected]<jallib%[email protected]> > > . > > For more options, visit this group at > >http://groups.google.com/group/jallib?hl=en. > > -- > Sébastien Lelonghttp://www.sirloon.nethttp://sirbot.org -- You received this message because you are subscribed to the Google Groups "jallib" group. To post to this group, send email to [email protected]. To unsubscribe from this group, send email to [email protected]. For more options, visit this group at http://groups.google.com/group/jallib?hl=en.
