Hi Vsurducan, Interesting.
I looked at some examples on the HC-06 also on Youtube (all with Arduino of course) and you see people struggle with the Arduino board since the serial interface is also used to program the Arduino and so they need to disconnect the module when they program it. Nice to have a separate programmer in that case. You may remember that I made some kind of Arduino Uno board for JAL (JALPIC One) but that uses the programming pins for programming the PIC so you can still use the serial interface. I downloaded some documentation of the HC-06 and I think it is a nice module to use so I think I will start with a JAL library for the HC-06. Kind regards, Rob ________________________________ Van: [email protected] <[email protected]> namens vsurducan <[email protected]> Verzonden: zaterdag 20 februari 2021 08:49 Aan: [email protected] <[email protected]> Onderwerp: Re: [jallib] Library for HC-06 Module? Hi Rob, In 2016 or so, I had a soil moisture sensor project solar powered, using HC 11 BLE for data transmission. A few thoughts about this is here (maybe it helps to set the device as peripheral, as central unit or to initiate a data transmission) : https://www.researchgate.net/publication/322078600_Efficient_low-power_wireless_communication_setup_for_an_autonomous_soil_moisture_sensor/link/5a48d02f458515f6b0578f9d/download Each HC BLE has a different AT command set. Some of the commands are documented in the producer datasheet some others are not. There are also devices with the same name (aka HC 11) but with different command sets, produced by different vendors. The most challenging was to put BLE on sleep and wake it at the requested time, because even though it's a low power, it drives quite much (17mA or so) during transmission. A library will be good. :) However it might work just for the HC06 tested... A typical sequence for defining some operating modes using constants: const byte BLEmode [] = "AT+MODE0" const byte BLEimme [] = "AT+IMME1" const byte BLEwake_up[] = "wakeu" const byte BLEreset[] = "AT+RESET" const byte BLEcentral[] = "AT+ROLE1" const byte BLEdisconnect[] = "AT" const byte BLEperipheral[] = "AT+ROLE0" const byte BLEsleep[] = "AT+SLEEP" const byte BLERFpower[] = "AT+POWE2" ; 0dBm const byte BLEname[] = " MS1 " const byte BLEset_name[] = "AT+NAMEMS1" const byte BLEconnect[] = "AT+CON884AEA6A0DA9" or a procedure for waking up the module (writing anything for a sufficient long time): procedure BLEwake is for 20 loop print_string (serial_hw_data, BLEwake_up) end loop end procedure On Fri, Feb 19, 2021 at 8:16 PM [email protected]<mailto:[email protected]> <[email protected]<mailto:[email protected]>> wrote: Hi all, I saw a question about a library for the HC-06 Module which is a bluetooth module. I had a quick look at the description and it does not seem to be a very complex device but a library could make life a bit easier. I was wondering if - besides the one question I have seen about this module - if there are more people that would like to have a library for this module. If so, let me know. i can give it a try (unless someone already created a library of course). Kind regards, Rob -- You received this message because you are subscribed to the Google Groups "jallib" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]<mailto:[email protected]>. To view this discussion on the web visit https://groups.google.com/d/msgid/jallib/d6eff2a3-71af-4172-ad2b-9f9590b3cef6n%40googlegroups.com<https://groups.google.com/d/msgid/jallib/d6eff2a3-71af-4172-ad2b-9f9590b3cef6n%40googlegroups.com?utm_medium=email&utm_source=footer>. -- You received this message because you are subscribed to the Google Groups "jallib" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]<mailto:[email protected]>. To view this discussion on the web visit https://groups.google.com/d/msgid/jallib/CAM%2Bj4qvT%3DcVrM%2Bzui-FjKT1jjU8UC0XnEXEs4FDas_0UTLAgdA%40mail.gmail.com<https://groups.google.com/d/msgid/jallib/CAM%2Bj4qvT%3DcVrM%2Bzui-FjKT1jjU8UC0XnEXEs4FDas_0UTLAgdA%40mail.gmail.com?utm_medium=email&utm_source=footer>. -- You received this message because you are subscribed to the Google Groups "jallib" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/jallib/AM0PR07MB6241D8C1BF1CB956F7643F18E6839%40AM0PR07MB6241.eurprd07.prod.outlook.com.
