Nice! HM11 can be programmed to be both master and slave, that was the reason I've worked with them. However those BLEs are quite difficult to be found in Europe, except for China. Let me know privately if I can be helpful somehow. I saw in libraries that your programming knowledge looks better that mine...
On Sat, Feb 20, 2021 at 11:40 AM Rob CJ <[email protected]> wrote: > Hi Vserducan, > > I saw the the HC-06 is a Bluetooth slave device only while the HC-05 can > also be used as master. I ordered both to see if I could make one library > to support both the HC-05 and the HC-06. I need to dive into some details > about the master mode since slave only is easier to use. > > It will take at least 6 weeks since I ordered them in China. That would > give me sufficient time to write the library 🙂. > > If it is ready and works, I will most likely make a video and post it on > Jallib & Jallist. > > Kind regards, > > Rob > > > > ------------------------------ > *Van:* [email protected] <[email protected]> namens vsurducan > <[email protected]> > *Verzonden:* zaterdag 20 februari 2021 10:12 > *Aan:* [email protected] <[email protected]> > *Onderwerp:* Re: [jallib] Library for HC-06 Module? > > Hi Rob, > Yes indeed, there are several PIC microcontrollers with up to 4 EUSART, > on those debugging and controlling BLE should be easier... > Testing the whole HC06 command set using an FTD module and a terminal > installed on a laptop is a good idea...:) > have a nice time! > > On Sat, Feb 20, 2021 at 10:41 AM Rob CJ <[email protected]> wrote: > > Hi Vsurducan, > > Interesting. > > I looked at some examples on the HC-06 also on Youtube (all with Arduino > of course) and you see people struggle with the Arduino board since the > serial interface is also used to program the Arduino and so they need to > disconnect the module when they program it. Nice to have a separate > programmer in that case. You may remember that I made some kind of Arduino > Uno board for JAL (JALPIC One) but that uses the programming pins for > programming the PIC so you can still use the serial interface. > > I downloaded some documentation of the HC-06 and I think it is a nice > module to use so I think I will start with a JAL library for the HC-06. > > Kind regards, > > Rob > > ------------------------------ > *Van:* [email protected] <[email protected]> namens vsurducan > <[email protected]> > *Verzonden:* zaterdag 20 februari 2021 08:49 > *Aan:* [email protected] <[email protected]> > *Onderwerp:* Re: [jallib] Library for HC-06 Module? > > Hi Rob, > In 2016 or so, I had a soil moisture sensor project solar powered, using > HC 11 BLE for data transmission. > A few thoughts about this is here (maybe it helps to set the device as > peripheral, as central unit or to initiate a data transmission) : > https://www.researchgate.net/publication/322078600_Efficient_low-power_wireless_communication_setup_for_an_autonomous_soil_moisture_sensor/link/5a48d02f458515f6b0578f9d/download > > Each HC BLE has a different AT command set. Some of the commands are > documented in the producer datasheet some others are not. > There are also devices with the same name (aka HC 11) but with different > command sets, produced by different vendors. > The most challenging was to put BLE on sleep and wake it at the requested > time, because even though it's a low power, it drives quite much (17mA or > so) during transmission. > > A library will be good. :) However it might work just for the HC06 > tested... > > > A typical sequence for defining some operating modes using constants: > const byte BLEmode [] = "AT+MODE0" > const byte BLEimme [] = "AT+IMME1" > const byte BLEwake_up[] = "wakeu" > const byte BLEreset[] = "AT+RESET" > const byte BLEcentral[] = "AT+ROLE1" > const byte BLEdisconnect[] = "AT" > const byte BLEperipheral[] = "AT+ROLE0" > const byte BLEsleep[] = "AT+SLEEP" > const byte BLERFpower[] = "AT+POWE2" ; 0dBm > const byte BLEname[] = " MS1 " > const byte BLEset_name[] = "AT+NAMEMS1" > const byte BLEconnect[] = "AT+CON884AEA6A0DA9" > > or a procedure for waking up the module (writing anything for a sufficient > long time): > procedure BLEwake is > for 20 loop > print_string (serial_hw_data, BLEwake_up) > end loop > end procedure > > > On Fri, Feb 19, 2021 at 8:16 PM [email protected] <[email protected]> > wrote: > > Hi all, > > I saw a question about a library for the HC-06 Module which is a bluetooth > module. I had a quick look at the description and it does not seem to be a > very complex device but a library could make life a bit easier. > > I was wondering if - besides the one question I have seen about this > module - if there are more people that would like to have a library for > this module. > > If so, let me know. i can give it a try (unless someone already created a > library of course). > > Kind regards, > > Rob > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/d6eff2a3-71af-4172-ad2b-9f9590b3cef6n%40googlegroups.com > <https://groups.google.com/d/msgid/jallib/d6eff2a3-71af-4172-ad2b-9f9590b3cef6n%40googlegroups.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/CAM%2Bj4qvT%3DcVrM%2Bzui-FjKT1jjU8UC0XnEXEs4FDas_0UTLAgdA%40mail.gmail.com > <https://groups.google.com/d/msgid/jallib/CAM%2Bj4qvT%3DcVrM%2Bzui-FjKT1jjU8UC0XnEXEs4FDas_0UTLAgdA%40mail.gmail.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/AM0PR07MB6241D8C1BF1CB956F7643F18E6839%40AM0PR07MB6241.eurprd07.prod.outlook.com > <https://groups.google.com/d/msgid/jallib/AM0PR07MB6241D8C1BF1CB956F7643F18E6839%40AM0PR07MB6241.eurprd07.prod.outlook.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/CAM%2Bj4qtHDhWb-e7CRhMNy_zX4Wbjrkg2Px0kJxv%3D2zcigk8v2Q%40mail.gmail.com > <https://groups.google.com/d/msgid/jallib/CAM%2Bj4qtHDhWb-e7CRhMNy_zX4Wbjrkg2Px0kJxv%3D2zcigk8v2Q%40mail.gmail.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/AM0PR07MB62412E3B0327D8E428CD6C72E6839%40AM0PR07MB6241.eurprd07.prod.outlook.com > <https://groups.google.com/d/msgid/jallib/AM0PR07MB62412E3B0327D8E428CD6C72E6839%40AM0PR07MB6241.eurprd07.prod.outlook.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "jallib" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/jallib/CAM%2Bj4qvAig1MBwjB-M1w6f8CJVeRSaZk-AnViy6%3DbATBGoKGsw%40mail.gmail.com.
