Hi all,
a pure resistor takes only "active power". Inductors and capacitors also take
"reactive power", both kinds of power combined are called "apparent power" (all
of the names translate similarly to dutch).
There are cheap devices, which do measure neither of the three but completly
wrong values when loaded inductively or capacitively. But, from what I read
before, the meter is provided by your utility company, therefore it must be a
device which correctly measures "active power". It could, however, also output
one or both of the other powers, or a number called "power factor" or "cos phi".
Greets,Kiste
Am Mittwoch, 20. Juli 2022 um 09:53:08 MESZ hat hans
<[email protected]> Folgendes geschrieben:
Hi Vasile,my site www.tweeduuster.nl works fine. Sorry for the mistake
What do you mean with reactive energy? I shows in and out Kwhr and save the
data for some time.
Op woensdag 20 juli 2022 om 06:24:09 UTC+2 schreef vasile:
Hans, your site is down?Does your meter measure reactive energy too? Thx.
On Tue, Jul 19, 2022 at 8:48 PM hans <[email protected]> wrote:
Hi Rob,
If you look at my site, www.teeduuster.nl, on the first page you will find
SMART METER READER. This animal did fine until last week, but our energy
supplier has placed another meter with something different. Hence. I'll see
what I can do with your tips. thanks again.
regards
HansOp dinsdag 19 juli 2022 om 18:42:33 UTC+2 schreef [email protected]:
Hi Hans,
This seems to be a very old library completely written in assembly.
I suggest you use the current library pic_data_eeprom.jal and replace the
following:
- Program_EEprom_Read --> data_eeprom_read_word
- Program_EEprom --> data_eeprom_word
- Program_EEprom_Write --> data_eeprom_write_word
You can use the same parameters in both procedures and functions. It should
then work again.
But please check this library and read the note about the EEPROM offset
(EEPROM_ADDRESS_OFFSET) since some PICs need it and I do not know which one you
are using.
Kind regards,
Rob
Van: [email protected] <[email protected]> namens hans
<[email protected]>
Verzonden: maandag 18 juli 2022 21:23
Aan: jallib <[email protected]>
Onderwerp: Re: [jallib] Pic_program_eeprom I used the pic-data-eeprom and the
the attached lib in a years_old_still_working-program but the attached is not
working anymore. I got errors in compiling.
Op maandag 18 juli 2022 om 18:48:43 UTC+2 schreef [email protected]:
Hi Hans,
Was your plan to program the eeprom separately or program eeprom from your JAL
program?
You can program eeprom with a PICkit3 (and I assume also a Pickit2) and for
programming it from your JAL program you can use pic_data_eeprom.jal.
Kind regards,
Rob
Van:[email protected] <[email protected]> namens hans
<[email protected]>
Verzonden: maandag 18 juli 2022 17:23
Aan: jallib <[email protected]>
Onderwerp: [jallib] Pic_program_eeprom Hello,
For a very old program I used the lib pic_program_eeprom, does it still exist
somewhere?
greetings
Hans
--
You received this message because you are subscribed to the Google Groups
"jallib" group.
To unsubscribe from this group and stop receiving emails from it, send an email
[email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/jallib/29887325-b407-44e9-b6b1-b886f076ab3bn%40googlegroups.com.
--
You received this message because you are subscribed to the Google Groups
"jallib" group.
To unsubscribe from this group and stop receiving emails from it, send an email
[email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/jallib/3b1192a6-c318-4916-aee8-48796ee17dacn%40googlegroups.com.
--
You received this message because you are subscribed to the Google Groups
"jallib" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/jallib/d0a1275f-7e87-4cfd-a916-1e588b63f5cen%40googlegroups.com.
--
You received this message because you are subscribed to the Google Groups
"jallib" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/jallib/9437eff2-56c6-44eb-a398-c168d5142fa9n%40googlegroups.com.
--
You received this message because you are subscribed to the Google Groups
"jallib" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/jallib/706881805.2121614.1658304790373%40mail.yahoo.com.
