Hi Rob morning test. Suddenly doesn't work anymore. Scoop doesn't give a signal either. Blink a led on both outputs C3 and C5 tested and freq to 16 (oB101) all works well.
Op donderdag 25 augustus 2022 om 22:20:49 UTC+2 schreef hans: > Hi Rob, > Hi Rob, > compiled and loaded with Pckit. Okay. Put on test board, leds on C3 and > C5. 33K on mclr. LVP off. Both leds go on and off but no light variation. > attached used program > > Op donderdag 25 augustus 2022 om 20:55:40 UTC+2 schreef hans: > >> Hi Rob, >> I put the file I showed yesterday in a separate folder. Add the three >> files you posted. When I compile now I don't get any errors anymore. I can >> see that he uses the common, but I don't know which of the other two. I'm >> going to test the case tomorrow to see if it works. >> thanks again >> regards >> Hans >> >> Op donderdag 25 augustus 2022 om 19:13:07 UTC+2 schreef >> [email protected]: >> >>> Hi Hans, >>> >>> You discovered a limitation in some of the PWM libraries. For newer PICs >>> some things have changed. >>> >>> I modified 3 libraries to get it compiling again using your program but >>> did not test this, see attachement. >>> >>> Can you include these libraries in the same directory as your main >>> program, test it and see if it works? >>> >>> I can test it later this weekend but if you have tested it and it works >>> I can skip that. If all is OK I will upload them the Jallib. >>> >>> Thanks. >>> >>> Kind regards, >>> >>> Rob >>> >>> ------------------------------ >>> *Van:* [email protected] <[email protected]> namens hans < >>> [email protected]> >>> *Verzonden:* woensdag 24 augustus 2022 20:34 >>> *Aan:* jallib <[email protected]> >>> *Onderwerp:* Re: [jallib] !6F15324 PWM RC5 and RC3 >>> >>> hello Rob,, >>> Have tried long time but many( 23) errors. To much for this old chap. >>> regards >>> Hans >>> >>> Op dinsdag 23 augustus 2022 om 19:10:00 UTC+2 schreef [email protected] >>> : >>> >>> Hi Hans, >>> >>> I did not see a sample file using two PWM's. I assume you can just >>> include two PWM libraries and give it a try. >>> >>> Note that for this specific PIC you can use PWM3, PWM4, PWM5 and PWM6 >>> since for this PIC they start at 3. >>> >>> I recently added libraries for PWM5 and PWM6 and sample programs for >>> that. >>> >>> As a test I of your challenge I combined the two pwm's from one of the >>> sample files by just copying the lines of pwm5 and change them into pwm6 so >>> the behaviour for both leds is the same, see attached file. >>> >>> The compiler finds it OK but you need to test if it works for you (I did >>> not test this) 🙂. >>> >>> Kind regards, >>> >>> Rob >>> >>> >>> >>> ------------------------------ >>> *Van:* [email protected] <[email protected]> namens hans < >>> [email protected]> >>> *Verzonden:* dinsdag 23 augustus 2022 13:57 >>> *Aan:* jallib <[email protected]> >>> *Onderwerp:* [jallib] !6F15324 PWM RC5 and RC3 >>> >>> Hello all. >>> I am looking for an example to use the 16F15324 for two PWM motor dirver >>> outputs. >>> Is there any? >>> regards >>> Hans >>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "jallib" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/jallib/5863d968-50c5-4e84-97d9-75ea6a9b41d0n%40googlegroups.com >>> >>> <https://groups.google.com/d/msgid/jallib/5863d968-50c5-4e84-97d9-75ea6a9b41d0n%40googlegroups.com?utm_medium=email&utm_source=footer> >>> . >>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "jallib" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/jallib/9cd3c949-d591-450f-b607-a1b070a9930bn%40googlegroups.com >>> >>> <https://groups.google.com/d/msgid/jallib/9cd3c949-d591-450f-b607-a1b070a9930bn%40googlegroups.com?utm_medium=email&utm_source=footer> >>> . >>> >> -- You received this message because you are subscribed to the Google Groups "jallib" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/jallib/fbb5ca2e-4790-4074-8b95-94650b5fd140n%40googlegroups.com.
