Hi Rob, It works great.. Thanks again and again. regards Hans Op zaterdag 27 augustus 2022 om 10:56:37 UTC+2 schreef [email protected]:
> Hi Hans, > > I fixed the problem. There where actually two problems: > > 1. The PIC you are using has 3 prescaler bits instead of 2. The > frequency would then not be correct. > 2. The PIC you are using has a separate clock register for Timer 2. > The default of that register is that it does not use Fosc/4 as input and > because of that Timer 2 was not running. > > Attached the update of the files. Please put them in your directory for > testing. I also removed the deprecated functions from pwm3.jal and pwm4.jal > since sufficient time has passed for JAL users not to use deprecated > functions. It makes the code cleaner. > > It works with your program but please remove the statement CCP1CON = TRUE > from your program. It is not needed. I attached the version of your program > again but changed the clock frequency to 32 MHz. The program also works > with 4 MHz as in your original program. I also changed the program a bit. > When the brightness of one LED increases, the other one decreases and the > other way around. I changed it so that you can see that both LEDs work > independently. > > Let me know if it also works for you. If so I will upload the changed > files to Jallib. > > Thanks. > > Kind regards, > > Rob > > ------------------------------ > *Van:* [email protected] <[email protected]> namens hans < > [email protected]> > *Verzonden:* vrijdag 26 augustus 2022 09:11 > > *Aan:* jallib <[email protected]> > *Onderwerp:* Re: [jallib] !6F15324 PWM RC5 and RC3 > Hi Rob > morning test. Suddenly doesn't work anymore. Scoop doesn't give a signal > either. > Blink a led on both outputs C3 and C5 tested and freq to 16 (oB101) all > works well. > > Op donderdag 25 augustus 2022 om 22:20:49 UTC+2 schreef hans: > > Hi Rob, > Hi Rob, > compiled and loaded with Pckit. Okay. Put on test board, leds on C3 and > C5. 33K on mclr. LVP off. Both leds go on and off but no light variation. > attached used program > > Op donderdag 25 augustus 2022 om 20:55:40 UTC+2 schreef hans: > > Hi Rob, > I put the file I showed yesterday in a separate folder. Add the three > files you posted. When I compile now I don't get any errors anymore. I can > see that he uses the common, but I don't know which of the other two. I'm > going to test the case tomorrow to see if it works. > thanks again > regards > Hans > > Op donderdag 25 augustus 2022 om 19:13:07 UTC+2 schreef [email protected] > : > > Hi Hans, > > You discovered a limitation in some of the PWM libraries. For newer PICs > some things have changed. > > I modified 3 libraries to get it compiling again using your program but > did not test this, see attachement. > > Can you include these libraries in the same directory as your main > program, test it and see if it works? > > I can test it later this weekend but if you have tested it and it works I > can skip that. If all is OK I will upload them the Jallib. > > Thanks. > > Kind regards, > > Rob > > ------------------------------ > *Van:* [email protected] <[email protected]> namens hans < > [email protected]> > *Verzonden:* woensdag 24 augustus 2022 20:34 > *Aan:* jallib <[email protected]> > *Onderwerp:* Re: [jallib] !6F15324 PWM RC5 and RC3 > > hello Rob,, > Have tried long time but many( 23) errors. To much for this old chap. > regards > Hans > > Op dinsdag 23 augustus 2022 om 19:10:00 UTC+2 schreef [email protected]: > > Hi Hans, > > I did not see a sample file using two PWM's. I assume you can just include > two PWM libraries and give it a try. > > Note that for this specific PIC you can use PWM3, PWM4, PWM5 and PWM6 > since for this PIC they start at 3. > > I recently added libraries for PWM5 and PWM6 and sample programs for that. > > As a test I of your challenge I combined the two pwm's from one of the > sample files by just copying the lines of pwm5 and change them into pwm6 so > the behaviour for both leds is the same, see attached file. > > The compiler finds it OK but you need to test if it works for you (I did > not test this) 🙂. > > Kind regards, > > Rob > > > > ------------------------------ > *Van:* [email protected] <[email protected]> namens hans < > [email protected]> > *Verzonden:* dinsdag 23 augustus 2022 13:57 > *Aan:* jallib <[email protected]> > *Onderwerp:* [jallib] !6F15324 PWM RC5 and RC3 > > Hello all. > I am looking for an example to use the 16F15324 for two PWM motor dirver > outputs. > Is there any? > regards > Hans > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/5863d968-50c5-4e84-97d9-75ea6a9b41d0n%40googlegroups.com > > <https://groups.google.com/d/msgid/jallib/5863d968-50c5-4e84-97d9-75ea6a9b41d0n%40googlegroups.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/9cd3c949-d591-450f-b607-a1b070a9930bn%40googlegroups.com > > <https://groups.google.com/d/msgid/jallib/9cd3c949-d591-450f-b607-a1b070a9930bn%40googlegroups.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/fbb5ca2e-4790-4074-8b95-94650b5fd140n%40googlegroups.com > > <https://groups.google.com/d/msgid/jallib/fbb5ca2e-4790-4074-8b95-94650b5fd140n%40googlegroups.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "jallib" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/jallib/126e96bf-b39b-4051-bee6-65dbc0668d54n%40googlegroups.com.
