On 14/11/2007, tiffany <[EMAIL PROTECTED]> wrote: > > I am using "all active threads in current thread group", what does this mean > if I have the following configuration? Do I have to care number of threads > in this case to configure the constant throughput timer? > > threads: 10 > Ramp up period: 60
Every 6 seconds, another thread becomes active. > constant throughput timer: 17.0 ( I want to have frequency=100/hr). 17.0 * 60 = 1020./hour You need 100/60 = 1.66/minute. It's basic arithmetic ... > Iterations: 100 > > ============ > > sebb-2-2 wrote: > > > > On 09/11/2007, tiffany <[EMAIL PROTECTED]> wrote: > >> > >> The calculations is based on 1 thread (1 user) or number of threads > >> doesn't > >> count? > >> > >> Actually, I have a test with the following configuration: > >> > >> threads: 1 > >> iterations: 100 > >> constant throughput timer: 30.0 (all active threads in current thread > >> group) > >> > >> Frequency needs per hour: 200 > >> > >> By the calcuation: I should put 3.33 per min. I tried it to run with > >> constant throughput timer: 3.33 (all active threads in current thread > >> group) > >> , it did't give me the right frequency( in hr), > > > > what did it give? > > > >> by testing, I figure it out, > >> I need to set constant throughput timer: 30.0 in order to have frequency= > >> 200 /hr. > >> > >> I don't really understand this. What about if threads=120, what should I > >> set > >> in constant throughput timer?? > > > > If you are using anything but "this thread only", then it does not > > matter how many threads there are - the delays are calculated as > > needed to provide the throughput. > > > >> > >> ================= > >> > >> sebb-2 wrote: > >> > > >> > 200 per hour=200/60 per min=3.33 per min > >> > > >> > On 18/09/2007, tiffany <[EMAIL PROTECTED]> wrote: > >> >> > >> >> Thanks for the answer. > >> >> > >> >> I still have a question, if I want my test case which consists 9 > >> requests > >> >> run 200 times per hour. How to calculate the throughput time for > >> it(What > >> >> should I set in the Constant Throughput Timer ?) > >> >> > >> >> Thanks, > >> >> Tiffany > >> >> ===================== > >> >> > >> >> sebb-2 wrote: > >> >> > > >> >> > Constant Timer always sleeps for the amount of time specified. > >> >> > > >> >> > Constant Throughput Timer sleeps for as long as necessary to try and > >> >> > maintain the throughput. > >> >> > > >> >> > On 13/09/2007, tiffany <[EMAIL PROTECTED]> wrote: > >> >> >> > >> >> >> Hi, > >> >> >> > >> >> >> I am not sure the difference % the usage of Constant Timer and > >> >> Constant > >> >> >> throughput timer even I have read the user manual. > >> >> >> > >> >> >> I try to do a web load test with 3 test cases, all 3 test cases are > >> in > >> >> a > >> >> >> test plan as the following: > >> >> >> > >> >> >> - test plan > >> >> >> - thread group 1 > >> >> >> - HTTP request > >> >> >> - other requests... > >> >> >> - constant timer/constant throughput timer > >> >> >> - thread group 2 > >> >> >> - HTTP request > >> >> >> - other requests... > >> >> >> - constant timer/constant throughput timer > >> >> >> - thread group 3 > >> >> >> - HTTP request > >> >> >> - other requests... > >> >> >> - constant timer/constant throughput timer > >> >> >> > >> >> >> > >> >> >> What is the difference of using constant timer and constant > >> throughput > >> >> >> timer > >> >> >> in each thread group? Actually, I try to create a test plan with 3 > >> >> test > >> >> >> cases on it and each test case needs to run with different > >> frequency. > >> >> For > >> >> >> example : > >> >> >> test case 1 needs to run 20 times per hour, > >> >> >> test case 2 needs to run 100 times per hour, > >> >> >> test case 3 needs to run 60 times per hour. > >> >> >> > >> >> >> What timer should I use in the above case? > >> >> > > >> >> > Constant Throughput Timer. > >> >> > > >> >> >> Thanks, > >> >> >> Tiffany > >> >> >> > >> >> >> > >> >> >> > >> >> >> -- > >> >> >> View this message in context: > >> >> >> > >> >> > >> http://www.nabble.com/Constant-Timer-vs-Constant-throughput-timer-tf4437423.html#a12660224 > >> >> >> Sent from the JMeter - User mailing list archive at Nabble.com. > >> >> >> > >> >> >> > >> >> >> > >> --------------------------------------------------------------------- > >> >> >> To unsubscribe, e-mail: [EMAIL PROTECTED] > >> >> >> For additional commands, e-mail: > >> [EMAIL PROTECTED] > >> >> >> > >> >> >> > >> >> > > >> >> > > >> --------------------------------------------------------------------- > >> >> > To unsubscribe, e-mail: [EMAIL PROTECTED] > >> >> > For additional commands, e-mail: [EMAIL PROTECTED] > >> >> > > >> >> > > >> >> > > >> >> > >> >> -- > >> >> View this message in context: > >> >> > >> http://www.nabble.com/Constant-Timer-vs-Constant-throughput-timer-tf4437423.html#a12762992 > >> >> Sent from the JMeter - User mailing list archive at Nabble.com. > >> >> > >> >> > >> >> --------------------------------------------------------------------- > >> >> To unsubscribe, e-mail: [EMAIL PROTECTED] > >> >> For additional commands, e-mail: [EMAIL PROTECTED] > >> >> > >> >> > >> > > >> > --------------------------------------------------------------------- > >> > To unsubscribe, e-mail: [EMAIL PROTECTED] > >> > For additional commands, e-mail: [EMAIL PROTECTED] > >> > > >> > > >> > > >> > >> -- > >> View this message in context: > >> http://www.nabble.com/Constant-Timer-vs-Constant-throughput-timer-tf4437423.html#a13673859 > >> Sent from the JMeter - User mailing list archive at Nabble.com. > >> > >> > >> --------------------------------------------------------------------- > >> To unsubscribe, e-mail: [EMAIL PROTECTED] > >> For additional commands, e-mail: [EMAIL PROTECTED] > >> > >> > > > > --------------------------------------------------------------------- > > To unsubscribe, e-mail: [EMAIL PROTECTED] > > For additional commands, e-mail: [EMAIL PROTECTED] > > > > > > > > -- > View this message in context: > http://www.nabble.com/Constant-Timer-vs-Constant-throughput-timer-tf4437423.html#a13753103 > Sent from the JMeter - User mailing list archive at Nabble.com. > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [EMAIL PROTECTED] > For additional commands, e-mail: [EMAIL PROTECTED] > > --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
