Hi All, It was a known issue with 2.2 firmware on my PIC. JTAC supplied a newer firmware which has fixed the issue
Thanks Lee -- Lee Hetherington Technical Services Lead REDtechnology.com T: +44 (0) 1865 880800 F: +44 (0) 1865 880865 W: www.REDtechnology.com Email Disclaimer: "This e-mail is for the use of the intended recipient(s) only. Any views or opinions presented are solely those of the author and do not necessarily represent those of REDtechnology.com or any of it's Affiliates. If you are not the intended recipient, be advised that you have received this email in error and that any use, dissemination, forwarding, printing, or copying of this email is strictly prohibited. We have taken precautions to minimize the risk of transmitting software viruses, but we advise you to carry out your own virus checks on any attachment to this message. We cannot accept liability for any loss or damage caused by software viruses." -----Original Message----- From: Vineet Venugopal [mailto:[EMAIL PROTECTED] Sent: 17 June 2008 16:56 To: Lee Hetherington Subject: Re: [j-nsp] Serial Question Hi Lee, I think this is a known issue for the JUNOS version. I guess you would have to perform an upgradation of JUNOS or the downgrade the firmware of the PIC to resolve this issue :) Thanks Vineet On 6/17/08, Lee Hetherington <[EMAIL PROTECTED]> wrote: > Hi Vineet, > > The Junos version is 9.0R1.10, the firmware of the PIC is 2.2 > > J-TAC are also asking the same questions now :) > > Thanks, > > Lee > > -----Original Message----- > From: Vineet Venugopal [mailto:[EMAIL PROTECTED] > Sent: 17 June 2008 16:43 > To: Lee Hetherington > Cc: [EMAIL PROTECTED]; [email protected] > Subject: Re: [j-nsp] Serial Question > > Hi Lee, > > Can you confirm the JUNOS version running on the Router as well as the > firmware version of the interface "show system firmware"? > > Regards > Vineet > > On 6/17/08, Lee Hetherington <[EMAIL PROTECTED]> wrote: > > Hi Alain, > > > > Im also not sure why I configured the clocking type :) > > > > I will connect it all up later on and drop you the output. > > > > Thanks for this > > > > Lee > > > > > > -----Original Message----- > > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] > > Sent: 17 June 2008 16:13 > > To: Lee Hetherington; [email protected] > > Subject: RE: [j-nsp] Serial Question > > > > Hi Lee > > > > Can you provide us for some traces: > > > > Monitor trafic interface se-1/0/1 > > We will see the lmi traffic > > And > > Show interface se-1/0/1 extensive > > > > I believe it's an LMI problem > > Normaly the default lmi on Juniper is ansi like the one you've configured > > on Cisco (so this should be OK) > > But perhaps the keepalive could be adapted (5 ?) > > I am also wondering why you configured "serial-option: clocking-mode loop" ! > > > > > > Alain > > > > > > > > > > -----Message d'origine----- > > De : [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] De la part de Lee > > Hetherington > > Envoyé : mardi 17 juin 2008 14:06 > > À : [email protected] > > Objet : [j-nsp] Serial Question > > > > Hi All, > > > > I have a J2320-JH which is replacing an aging Cisco 3640. I am having > > trouble bringing up an x.21 leased line. It brings up the line, but in > > cisco terms not the protocol. It keeps telling me on my subinterface > > "flags: down". > > > > Below are my cisco and juniper configs. Anyone any ideas, the isp is being > > particularly un-helpful. > > > > Cisco: > > > > ! > > interface Serial0/0 > > bandwidth 2048 > > no ip address > > encapsulation frame-relay > > no ip mroute-cache > > keepalive 5 > > no fair-queue > > frame-relay lmi-type ansi > > ! > > interface Serial0/0.16 point-to-point > > description Telstra Circuit > > ip address 154.32.xxx.81 255.255.255.252 no cdp enable frame-relay > > interface-dlci 16 IETF ! > > > > > > Juniper: > > > > se-1/0/1 { > > description Telstra; > > mtu 1500; > > encapsulation frame-relay; > > serial-options { > > clocking-mode loop; > > } > > unit 0 { > > description "Telstra Serial Circuit MXFS203988"; > > point-to-point; > > dlci 16; > > family inet { > > address 154.32.152.81/30; > > } > > } > > } > > > > Many Thanks, > > > > Lee > > > > _______________________________________________ > > juniper-nsp mailing list [email protected] > > https://puck.nether.net/mailman/listinfo/juniper-nsp > > > > -- > > This message has been scanned for viruses and > > dangerous content by REDScanner, and is > > believed to be clean. > > > > _______________________________________________ > > juniper-nsp mailing list [email protected] > > https://puck.nether.net/mailman/listinfo/juniper-nsp > > > > > -- > ---Vineet > > -- > This message has been scanned for viruses and > dangerous content by REDScanner, and is > believed to be clean. > > -- ---Vineet -- This message has been scanned for viruses and dangerous content by REDScanner, and is believed to be clean. _______________________________________________ juniper-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/juniper-nsp
