Hello Hendrik, Thnx, it works !!
The local-interface loopback, the IP-adres.. .does it matters ? Kind regards, Tom ________________________________________ Van: [email protected] [[email protected]] namens Hendrik Kahmann [[email protected]] Verzonden: dinsdag 2 november 2010 8:07 Aan: Diogo Montagner; [email protected] Onderwerp: Re: [j-nsp] ERX310 PPPoE and multiple Virtual-routers Hello, as far as i know, this might be your solution: aaa domain-map "ABC" router-name "ABC" local-interface loopback 101 ipv6-router-name default strip-domain enable ! aaa domain-map "DEF" router-name "DEF" local-interface loopback 102 ipv6-router-name default strip-domain enable ! profile pppoe-defaults ip mtu 1492 ip sa-validate ip tcp adjust-mss 1400 ppp authentication pap ! interface gigabitEthernet 1/0.10 vlan id 10 pppoe pppoe auto-configure pppoe remote-circuit-id pppoe profile any pppoe-defaults ! interface gigabitEthernet 1/0.20 vlan id 20 pppoe pppoe auto-configure pppoe remote-circuit-id pppoe profile any pppoe-defaults ! Users would be j...@abc or j...@def Kind regards, Hendrik Am 02.11.2010 05:23, schrieb Diogo Montagner: > AFAIK, you need different subinterfaces for each virtual-router. > > Eg.: > > Vlan 10 - VR ABC > Vlan 20 - VR DEF > ... > > Rgs > > On 11/2/10, Tom Teeuwen<[email protected]> wrote: >> Hello, >> >> >> >> I'm configuring an ERX310 for PPPoE termination. >> >> From the all DSLAM's we get about 190 tagged VLAN's. >> >> So for every VLAN i need to create a subinterface. >> >> >> >> Now we want to create multiple virtual-routers for customers who want to get >> an VPN. >> >> In the basic setup without VR's(only the default) i have a profile bounded >> to an subinterface. >> >> The profile config: >> >> profile Test >> ip unnumbered gigabitEthernet 1/1.102 >> ppp authentication virtual-router default pap >> >> >> >> Now I created a VR and a domain-map and mapped a domain to the VR >> >> But the PPPoE request is comming from the same subinterface as above >> specified (where i attached a profile to the subinterface) >> >> Problem is that I only can attach one profile to a subinterface. >> >> I want the following: >> >> - based on a domain attach the PPPoE session to a specific VR >> >> - PPPoE request can come from different subinterfaces >> >> >> >> Example: >> >> Customer 1 form subif 1 to VR-A >> >> Customer 2 from subif 1 to VR-B >> >> Customer 3 from subif 2 to VR-A >> >> Customer 4 from subif 2 to VR-B >> >> >> >> Kind regards, >> >> Tom >> _______________________________________________ >> juniper-nsp mailing list [email protected] >> https://puck.nether.net/mailman/listinfo/juniper-nsp >> -- Hendrik Kahmann B.Sc. Wirtschaftsinformatik Planung - Technische Produktentwicklung Telefon: +49 441 8000 2778 mailto:[email protected] ___________________________________________ EWE TEL GmbH Cloppenburger Straße 310 26133 Oldenburg Handelsregister Amtsgericht Oldenburg HRB 3723 Vorsitzender des Aufsichtsrates: Dr. Werner Brinker Geschäftsführung: Hans-Joachim Iken (Vorsitzender), Ulf Heggenberger, Dr. Norbert Schulz, Dirk Thole Homepage: http://www.ewetel.de ___________________________________________ _______________________________________________ juniper-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/juniper-nsp _______________________________________________ juniper-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/juniper-nsp
