SAt Mon, 28 Nov 2016 20:55:04 +0100 (CET),
Deloin via juniper-nsp <[email protected]> wrote:
> 
> 
> Hello, 
> 
> I have 2 EX4600 switchs. 
> They have the same symetric configurations: 
> 
> 
> SWITCH EX4600-1                        SWITCH EX4600-2 
> 
> interfaces {                           interfaces { 
>   xe-0/0/1 {                             xe-0/0/1 { 
>     unit 0 {                               unit 0 { 
>       family ethernet-switching {            family ethernet-switching { 
>         interface-mode access;                 interface-mode access; 
>         vlan {                                 vlan { 
>           members vlan-RESEAUX;                  members vlan-RESEAUX; 
>         }                                      } 
>         storm-control default;                 storm-control default; 
>       }                                      } 
>     }                                      } 
>   }                                      }
>  
>   irb {                                  irb { 
>     unit 0 {                               unit 0 { 
>       family inet {                          family inet { 
>         address 10.101.0.4/16;                 address 10.101.0.5/16; 
>       }                                      } 
>     }                                      } 
>   }                                      } 
> }                                      } 
> 
> 
> routing-options {                      routing-options { 
>   static {                               static { 
>     route 0.0.0.0/0 next-hop 10.101.0.1;   route 0.0.0.0/0 next-hop 
> 10.101.0.1; 
>   }                                      } 
> }                                      } 
> 
> 
> vlans {                                vlans { 
>   default {                              default { 
>     vlan-id 1;                             vlan-id 1; 
>   }                                      } 
> 
>   vlan-RESEAUX {                         vlan-RESEAUX { 
>     vlan-id 98;                            vlan-id 98; 
>     l3.interface irb.0;                    l3.interface irb.0; 
>   }                                      } 
> }                                      } 
> 
> I put an optic fiber between xe-0/0/1 from a switch and xe-0/0/1 from the 
> other switch.
> And I can't ping the @ 10.101.0.3 and 10.101.0.4 from each switchs.

you appear to have 2 interfaces connected, with a single fiber and a
/16 netblock assigned.  Then you ping .3 which is on neither
interface, so ... 'no route to host' normally means 'did not get an
arp reply, could not deliver packet'.

this sounds like it's working exactly as expected?

> I obtain :
> root@EX4600-01# run ping 10.101.0.3
> PING 10.101.0.3 (10.101.0.3): 56 data bytes
> ping: sendto: No route to host
> ping: sendto: No route to host
> ping: sendto: No route to host
> ping: sendto: No route to host
> the same for the other.
> 
> Can you help me. Can you tell me where is the mistake, or what I forget ?
> 
> Thank you !
> _______________________________________________
> juniper-nsp mailing list [email protected]
> https://puck.nether.net/mailman/listinfo/juniper-nsp
_______________________________________________
juniper-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/juniper-nsp

Reply via email to