The command you are looking for is called "show interfaces diagnostics optics".
2017-10-04 21:20 GMT+02:00 Aaron Gould <[email protected]>: > I put this into my ACX5048 in the lab today. actually 2 of them. > QSFP+-40G-ER4 (aka QSFPP-40GBASE-ER4) SMF 40 km 1310 nm optic > > > > Optic is seen in cli, but I see no led's on chassis and when I plug them > into each other, interfaces stay up/down. > > > > Is there something I need to do to make this 40 gig optic work in the > ACX5048 (JUNOS 15.1X54-D61.6) ? > > > > {master:0} > agould@eng-lab-5048-2> show interfaces terse | grep et- > et-0/0/48 up down > et-0/0/49 up down > > {master:0} > agould@eng-lab-5048-2> show interfaces et-0/0/48 > Physical interface: et-0/0/48, Enabled, Physical link is Down > Interface index: 657, SNMP ifIndex: 582 > Link-level type: Ethernet, MTU: 1514, LAN-PHY mode, Speed: 40Gbps, BPDU > Error: None, MAC-REWRITE Error: None, Loopback: Disabled, > Source filtering: Disabled, Flow control: Disabled, Media type: Fiber > Device flags : Present Running Down > Interface flags: Hardware-Down SNMP-Traps Internal: 0x4000 > Link flags : None > CoS queues : 8 supported, 8 maximum usable queues > Current address: 20:4e:71:45:d3:d3, Hardware address: 20:4e:71:45:d3:d3 > Last flapped : 2017-10-04 10:26:33 CDT (00:09:14 ago) > Input rate : 0 bps (0 pps) > Output rate : 0 bps (0 pps) > Active alarms : LINK > Active defects : LINK > Interface transmit statistics: Disabled > > {master:0} > agould@eng-lab-5048-2> show interfaces et-0/0/49 > Physical interface: et-0/0/49, Enabled, Physical link is Down > Interface index: 658, SNMP ifIndex: 583 > Link-level type: Ethernet, MTU: 1514, LAN-PHY mode, Speed: 40Gbps, BPDU > Error: None, MAC-REWRITE Error: None, Loopback: Disabled, > Source filtering: Disabled, Flow control: Disabled, Media type: Fiber > Device flags : Present Running Down > Interface flags: Hardware-Down SNMP-Traps Internal: 0x4000 > Link flags : None > CoS queues : 8 supported, 8 maximum usable queues > Current address: 20:4e:71:45:d3:d7, Hardware address: 20:4e:71:45:d3:d7 > Last flapped : 2017-10-04 10:27:53 CDT (00:07:56 ago) > Input rate : 0 bps (0 pps) > Output rate : 0 bps (0 pps) > Active alarms : LINK > Active defects : LINK > Interface transmit statistics: Disabled > > {master:0} > agould@eng-lab-5048-2> show chassis hardware > Hardware inventory: > Item Version Part number Serial number Description > Chassis (removed...) ACX5048 > Pseudo CB 0 > Routing Engine 0 BUILTIN BUILTIN ACX5K Routing > Engine > FPC 0 REV 07 650-060546 (removed...) ACX5048 > CPU BUILTIN BUILTIN FPC CPU > PIC 0 BUILTIN BUILTIN 48x10G-6x40G > > Xcvr 48 REV 01 740-059185 (removed...) QSFP+-40G-ER4 > Xcvr 49 REV 01 740-059185 (removed...) QSFP+-40G-ER4 > Power Supply 0 REV 04 740-043886 (removed...) JPSU-650W-DC-AFO > Power Supply 1 REV 04 740-043886 (removed...) JPSU-650W-DC-AFO > Fan Tray 0 ACX5K Fan Tray 0, > Front to Back Airflow - AFO > Fan Tray 1 ACX5K Fan Tray 1, > Front to Back Airflow - AFO > Fan Tray 2 ACX5K Fan Tray 2, > Front to Back Airflow - AFO > Fan Tray 3 ACX5K Fan Tray 3, > Front to Back Airflow - AFO > Fan Tray 4 ACX5K Fan Tray 4, > Front to Back Airflow - AFO > > > > > {master:0} > agould@eng-lab-5048-2> show chassis pic pic-slot 0 fpc-slot 0 > FPC slot 0, PIC slot 0 information: > Type 48x10G-6x40G > State Online > PIC version 2.7 > Uptime 99 days, 23 hours, 26 minutes, 3 seconds > > PIC port information: > Fiber Xcvr vendor Wave- > Xcvr > Port Cable type type Xcvr vendor part number length > Firmware > 48 40GBASE ER4 SM JUNIPER-FINISAR FTL4E1QE1C-J3 1301 nm > 0.0 > 49 40GBASE ER4 SM JUNIPER-FINISAR FTL4E1QE1C-J3 1301 nm > 0.0 > > > > - Aaron > > > > _______________________________________________ > juniper-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/juniper-nsp > _______________________________________________ juniper-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/juniper-nsp
