Hi, > If I've followed all this through properly: > > With KVM - mmu+caches are configured, but then disabled by 'kvm: allows kvm > cpu hotplug'. This 'arm64_relocate_new_kernel' function then runs at EL2 > with M=0, C=0, I=0. > > Without KVM - when there is no user of EL2, the mmu+caches are left in > whatever state the bootloader (or efi stub) left them in. From > Documentation/arm64/booting.txt: > > Instruction cache may be on or off. > and > > System caches which respect the architected cache maintenance by VA > > operations must be configured and may be enabled. > > So 'arm64_relocate_new_kernel' function could run at EL2 with M=0, C=?, I=?. > > I think this means you can't guarantee anything you are copying below > actually makes it through the caches - booting secondary processors may get > stale values. > > The EFI stub disables the M and C bits when booted at EL2 with uefi - but > it leaves the instruction cache enabled. You only clean the > reboot_code_buffer from the data cache, so there may be stale values in the > instruction cache. > > I think you need to disable the i-cache at EL1. If you jump to EL2, I think > you need to disable the I/C bits there too - as you can't rely on the code > in 'kvm: allows kvm cpu hotplug' to do this in a non-kvm case.
The SCTLR_ELx.I only affects the attributes that the I-cache uses to fetch with, not whether it is enabled (it cannot be disabled architecturally). It's not necessary to clear the I bit so long as the appropriate maintenance has occurred, though I believe that when the I bit is set instruction fetches may allocte in unified levels of cache, so additional consideration is required for that case. > > + /* Copy page. */ > > +1: ldp x22, x23, [x21] > > + ldp x24, x25, [x21, #16] > > + ldp x26, x27, [x21, #32] > > + ldp x28, x29, [x21, #48] > > + add x21, x21, #64 > > + stnp x22, x23, [x20] > > + stnp x24, x25, [x20, #16] > > + stnp x26, x27, [x20, #32] > > + stnp x28, x29, [x20, #48] > > + add x20, x20, #64 > > + tst x21, #(PAGE_SIZE - 1) > > + b.ne 1b > > + > > + /* dest += PAGE_SIZE */ > > + add x14, x14, PAGE_SIZE > > + b .Lnext > > + > > +.Ltest_indirection: > > + tbz x18, IND_INDIRECTION_BIT, .Ltest_destination > > + > > + /* ptr = addr */ > > + mov x15, x13 > > + b .Lnext > > + > > +.Ltest_destination: > > + tbz x18, IND_DESTINATION_BIT, .Lnext > > + > > + mov x16, x13 > > + > > + /* dest = addr */ > > + mov x14, x13 > > + > > +.Lnext: > > + /* entry = *ptr++ */ > > + ldr x18, [x15], #8 > > + > > + /* while (!(entry & DONE)) */ > > + tbz x18, IND_DONE_BIT, .Lloop > > + > > +.Ldone: > > + dsb sy > > + isb > > + ic ialluis > > + dsb sy > > Why the second dsb? > > > > + isb The first DSB ensures that the copied data is observable by the I-caches. The first ISB is unnecessary. The second DSB ensures that the I-cache maintenance is completed. The second ISB ensures that the I-cache maintenance is complete w.r.t. the current instruction stream. There could be instructions in the pipline fetched from the I-cache prior to invalidation which need to be cleared. Thanks, Mark. _______________________________________________ kexec mailing list [email protected] http://lists.infradead.org/mailman/listinfo/kexec
