Thanks Bjorn for replying on this thread.
On Wed, May 13, 2020 at 3:33 AM Bjorn Helgaas <[email protected]> wrote:
>
> [+cc linux-pci]
>
> On Mon, May 11, 2020 at 07:46:06PM -0700, Prabhakar Kushwaha wrote:
> > An SMMU Stream table is created by the primary kernel. This table is
> > used by the SMMU to perform address translations for device-originated
> > transactions. Any crash (if happened) launches the kdump kernel which
> > re-creates the SMMU Stream table. New transactions will be translated
> > via this new table..
> >
> > There are scenarios, where devices are still having old pending
> > transactions (configured in the primary kernel). These transactions
> > come in-between Stream table creation and device-driver probe.
> > As new stream table does not have entry for older transactions,
> > it will be aborted by SMMU.
> >
> > Similar observations were found with PCIe-Intel 82576 Gigabit
> > Network card. It sends old Memory Read transaction in kdump kernel.
> > Transactions configured for older Stream table entries, that do not
> > exist any longer in the new table, will cause a PCIe Completion Abort.
>
> That sounds like exactly what we want, doesn't it?
>
> Or do you *want* DMA from the previous kernel to complete? That will
> read or scribble on something, but maybe that's not terrible as long
> as it's not memory used by the kdump kernel.
>
Yes, Abort should happen. But it should happen in context of driver.
But current abort is happening because of SMMU and no driver/pcie
setup present at this moment.
Solution of this issue should be at 2 place
a) SMMU level: I still believe, this patch has potential to overcome
issue till finally driver's probe takeover.
b) Device level: Even if something goes wrong. Driver/device should
able to recover.
> > Returned PCIe completion abort further leads to AER Errors from APEI
> > Generic Hardware Error Source (GHES) with completion timeout.
> > A network device hang is observed even after continuous
> > reset/recovery from driver, Hence device is no more usable.
>
> The fact that the device is no longer usable is definitely a problem.
> But in principle we *should* be able to recover from these errors. If
> we could recover and reliably use the device after the error, that
> seems like it would be a more robust solution that having to add
> special cases in every IOMMU driver.
>
> If you have details about this sort of error, I'd like to try to fix
> it because we want to recover from that sort of error in normal
> (non-crash) situations as well.
>
Completion abort case should be gracefully handled. And device should
always remain usable.
There are 2 scenario which I am testing with Ethernet card PCIe-Intel
82576 Gigabit Network card.
I) Crash testing using kdump root file system: De-facto scenario
- kdump file system does not have Ethernet driver
- A lot of AER prints [1], making it impossible to work on shell
of kdump root file system.
- Note kdump shell allows to use makedumpfile, vmcore-dmesg applications.
II) Crash testing using default root file system: Specific case to
test Ethernet driver in second kernel
- Default root file system have Ethernet driver
- AER error comes even before the driver probe starts.
- Driver does reset Ethernet card as part of probe but no success.
- AER also tries to recover. but no success. [2]
- I also tries to remove AER errors by using "pci=noaer" bootargs
and commenting ghes_handle_aer() from GHES driver..
than different set of errors come which also never able to recover [3]
As per my understanding, possible solutions are
- Copy SMMU table i.e. this patch
OR
- Doing pci_reset_function() during enumeration phase.
I also tried clearing "M" bit using pci_clear_master during
enumeration but it did not help. Because driver re-set M bit causing
same AER error again.
-pk
---------------------------------------------------------------------------------------------------------------------------
[1] with bootargs having pci=noaer
[ 22.494648] {4}[Hardware Error]: Hardware error from APEI Generic
Hardware Error Source: 1
[ 22.512773] {4}[Hardware Error]: event severity: recoverable
[ 22.518419] {4}[Hardware Error]: Error 0, type: recoverable
[ 22.544804] {4}[Hardware Error]: section_type: PCIe error
[ 22.550363] {4}[Hardware Error]: port_type: 0, PCIe end point
[ 22.556268] {4}[Hardware Error]: version: 3.0
[ 22.560785] {4}[Hardware Error]: command: 0x0507, status: 0x4010
[ 22.576852] {4}[Hardware Error]: device_id: 0000:09:00.1
[ 22.582323] {4}[Hardware Error]: slot: 0
[ 22.586406] {4}[Hardware Error]: secondary_bus: 0x00
[ 22.591530] {4}[Hardware Error]: vendor_id: 0x8086, device_id: 0x10c9
[ 22.608900] {4}[Hardware Error]: class_code: 000002
[ 22.613938] {4}[Hardware Error]: serial number: 0xff1b4580, 0x90e2baff
[ 22.803534] pci 0000:09:00.1: AER: aer_status: 0x00004000,
aer_mask: 0x00000000
[ 22.810838] pci 0000:09:00.1: AER: [14] CmpltTO (First)
[ 22.817613] pci 0000:09:00.1: AER: aer_layer=Transaction Layer,
aer_agent=Requester ID
[ 22.847374] pci 0000:09:00.1: AER: aer_uncor_severity: 0x00062011
[ 22.866161] mpt3sas_cm0: 63 BIT PCI BUS DMA ADDRESSING SUPPORTED,
total mem (8153768 kB)
[ 22.946178] pci 0000:09:00.0: AER: can't recover (no error_detected callback)
[ 22.995142] pci 0000:09:00.1: AER: can't recover (no error_detected callback)
[ 23.002300] pcieport 0000:00:09.0: AER: device recovery failed
[ 23.027607] pci 0000:09:00.1: AER: aer_status: 0x00004000,
aer_mask: 0x00000000
[ 23.044109] pci 0000:09:00.1: AER: [14] CmpltTO (First)
[ 23.060713] pci 0000:09:00.1: AER: aer_layer=Transaction Layer,
aer_agent=Requester ID
[ 23.068616] pci 0000:09:00.1: AER: aer_uncor_severity: 0x00062011
[ 23.122056] pci 0000:09:00.0: AER: can't recover (no error_detected callback)
----------------------------------------------------------------------------------------------------------------------------
[2] Normal bootargs.
[ 54.252454] {6}[Hardware Error]: Hardware error from APEI Generic
Hardware Error Source: 1
[ 54.265827] {6}[Hardware Error]: event severity: recoverable
[ 54.271473] {6}[Hardware Error]: Error 0, type: recoverable
[ 54.281605] {6}[Hardware Error]: section_type: PCIe error
[ 54.287163] {6}[Hardware Error]: port_type: 0, PCIe end point
[ 54.296955] {6}[Hardware Error]: version: 3.0
[ 54.301471] {6}[Hardware Error]: command: 0x0507, status: 0x4010
[ 54.312520] {6}[Hardware Error]: device_id: 0000:09:00.1
[ 54.317991] {6}[Hardware Error]: slot: 0
[ 54.322074] {6}[Hardware Error]: secondary_bus: 0x00
[ 54.327197] {6}[Hardware Error]: vendor_id: 0x8086, device_id: 0x10c9
[ 54.333797] {6}[Hardware Error]: class_code: 000002
[ 54.351312] {6}[Hardware Error]: serial number: 0xff1b4580, 0x90e2baff
[ 54.358001] AER: AER recover: Buffer overflow when recovering AER
for 0000:09:00:1
[ 54.376852] pcieport 0000:00:09.0: AER: device recovery successful
[ 54.383034] igb 0000:09:00.1: AER: aer_status: 0x00004000,
aer_mask: 0x00000000
[ 54.390348] igb 0000:09:00.1: AER: [14] CmpltTO (First)
[ 54.397144] igb 0000:09:00.1: AER: aer_layer=Transaction Layer,
aer_agent=Requester ID
[ 54.409555] igb 0000:09:00.1: AER: aer_uncor_severity: 0x00062011
[ 54.551370] AER: AER recover: Buffer overflow when recovering AER
for 0000:09:00:1
[ 54.705214] AER: AER recover: Buffer overflow when recovering AER
for 0000:09:00:1
[ 54.758703] AER: AER recover: Buffer overflow when recovering AER
for 0000:09:00:1
[ 54.865445] AER: AER recover: Buffer overflow when recovering AER
for 0000:09:00:1
[ 54.888751] pcieport 0000:00:09.0: AER: device recovery successful
[ 54.894933] igb 0000:09:00.1: AER: aer_status: 0x00004000,
aer_mask: 0x00000000
[ 54.902228] igb 0000:09:00.1: AER: [14] CmpltTO (First)
[ 54.916059] igb 0000:09:00.1: AER: aer_layer=Transaction Layer,
aer_agent=Requester ID
[ 54.923972] igb 0000:09:00.1: AER: aer_uncor_severity: 0x00062011
[ 55.057272] AER: AER recover: Buffer overflow when recovering AER
for 0000:09:00:1
[ 274.571401] AER: AER recover: Buffer overflow when recovering AER
for 0000:09:00:1
[ 274.686138] AER: AER recover: Buffer overflow when recovering AER
for 0000:09:00:1
[ 274.786134] AER: AER recover: Buffer overflow when recovering AER
for 0000:09:00:1
[ 274.886141] AER: AER recover: Buffer overflow when recovering AER
for 0000:09:00:1
[ 397.792897] Workqueue: events aer_recover_work_func
[ 397.797760] Call trace:
[ 397.800199] __switch_to+0xcc/0x108
[ 397.803675] __schedule+0x2c0/0x700
[ 397.807150] schedule+0x58/0xe8
[ 397.810283] schedule_preempt_disabled+0x18/0x28
[ 397.810788] AER: AER recover: Buffer overflow when recovering AER
for 0000:09:00:1
[ 397.814887] __mutex_lock.isra.9+0x288/0x5c8
[ 397.814890] __mutex_lock_slowpath+0x1c/0x28
[ 397.830962] mutex_lock+0x4c/0x68
[ 397.834264] report_slot_reset+0x30/0xa0
[ 397.838178] pci_walk_bus+0x68/0xc0
[ 397.841653] pcie_do_recovery+0xe8/0x248
[ 397.845562] aer_recover_work_func+0x100/0x138
[ 397.849995] process_one_work+0x1bc/0x458
[ 397.853991] worker_thread+0x150/0x500
[ 397.857727] kthread+0x114/0x118
[ 397.860945] ret_from_fork+0x10/0x18
[ 397.864525] INFO: task kworker/223:2:2939 blocked for more than 122 seconds.
[ 397.871564] Not tainted 5.7.0-rc3+ #68
[ 397.875819] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs"
disables this message.
[ 397.883638] kworker/223:2 D 0 2939 2 0x00000228
[ 397.889121] Workqueue: ipv6_addrconf addrconf_verify_work
[ 397.894505] Call trace:
[ 397.896940] __switch_to+0xcc/0x108
[ 397.900419] __schedule+0x2c0/0x700
[ 397.903894] schedule+0x58/0xe8
[ 397.907023] schedule_preempt_disabled+0x18/0x28
[ 397.910798] AER: AER recover: Buffer overflow when recovering AER
for 0000:09:00:1
[ 397.911630] __mutex_lock.isra.9+0x288/0x5c8
[ 397.923440] __mutex_lock_slowpath+0x1c/0x28
[ 397.927696] mutex_lock+0x4c/0x68
[ 397.931005] rtnl_lock+0x24/0x30
[ 397.934220] addrconf_verify_work+0x18/0x30
[ 397.938394] process_one_work+0x1bc/0x458
[ 397.942390] worker_thread+0x150/0x500
[ 397.946126] kthread+0x114/0x118
[ 397.949345] ret_from_fork+0x10/0x18
---------------------------------------------------------------------------------------------------------------------------------
[3] with bootargs as pci=noaer and comment ghes_halder_aer() from AER driver
[ 69.037035] igb 0000:09:00.1 enp9s0f1: Reset adapter
[ 69.348446] {9}[Hardware Error]: Hardware error from APEI Generic
Hardware Error Source: 0
[ 69.356698] {9}[Hardware Error]: It has been corrected by h/w and
requires no further action
[ 69.365121] {9}[Hardware Error]: event severity: corrected
[ 69.370593] {9}[Hardware Error]: Error 0, type: corrected
[ 69.376064] {9}[Hardware Error]: section_type: PCIe error
[ 69.381623] {9}[Hardware Error]: port_type: 4, root port
[ 69.387094] {9}[Hardware Error]: version: 3.0
[ 69.391611] {9}[Hardware Error]: command: 0x0106, status: 0x4010
[ 69.397777] {9}[Hardware Error]: device_id: 0000:00:09.0
[ 69.403248] {9}[Hardware Error]: slot: 0
[ 69.407331] {9}[Hardware Error]: secondary_bus: 0x09
[ 69.412455] {9}[Hardware Error]: vendor_id: 0x177d, device_id: 0xaf84
[ 69.419055] {9}[Hardware Error]: class_code: 000406
[ 69.424093] {9}[Hardware Error]: bridge: secondary_status:
0x6000, control: 0x0002
[ 72.118132] igb 0000:09:00.1 enp9s0f1: igb: enp9s0f1 NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX
[ 73.995068] igb 0000:09:00.1: Detected Tx Unit Hang
[ 73.995068] Tx Queue <2>
[ 73.995068] TDH <0>
[ 73.995068] TDT <1>
[ 73.995068] next_to_use <1>
[ 73.995068] next_to_clean <0>
[ 73.995068] buffer_info[next_to_clean]
[ 73.995068] time_stamp <ffff9c1a>
[ 73.995068] next_to_watch <0000000097d42934>
[ 73.995068] jiffies <ffff9cd0>
[ 73.995068] desc.status <168000>
[ 75.987323] igb 0000:09:00.1: Detected Tx Unit Hang
[ 75.987323] Tx Queue <2>
[ 75.987323] TDH <0>
[ 75.987323] TDT <1>
[ 75.987323] next_to_use <1>
[ 75.987323] next_to_clean <0>
[ 75.987323] buffer_info[next_to_clean]
[ 75.987323] time_stamp <ffff9c1a>
[ 75.987323] next_to_watch <0000000097d42934>
[ 75.987323] jiffies <ffff9d98>
[ 75.987323] desc.status <168000>
[ 77.952661] {10}[Hardware Error]: Hardware error from APEI Generic
Hardware Error Source: 1
[ 77.971790] {10}[Hardware Error]: event severity: recoverable
[ 77.977522] {10}[Hardware Error]: Error 0, type: recoverable
[ 77.983254] {10}[Hardware Error]: section_type: PCIe error
[ 77.999930] {10}[Hardware Error]: port_type: 0, PCIe end point
[ 78.005922] {10}[Hardware Error]: version: 3.0
[ 78.010526] {10}[Hardware Error]: command: 0x0507, status: 0x4010
[ 78.016779] {10}[Hardware Error]: device_id: 0000:09:00.1
[ 78.033107] {10}[Hardware Error]: slot: 0
[ 78.037276] {10}[Hardware Error]: secondary_bus: 0x00
[ 78.066253] {10}[Hardware Error]: vendor_id: 0x8086, device_id: 0x10c9
[ 78.072940] {10}[Hardware Error]: class_code: 000002
[ 78.078064] {10}[Hardware Error]: serial number: 0xff1b4580, 0x90e2baff
[ 78.096202] igb 0000:09:00.1: Detected Tx Unit Hang
[ 78.096202] Tx Queue <2>
[ 78.096202] TDH <0>
[ 78.096202] TDT <1>
[ 78.096202] next_to_use <1>
[ 78.096202] next_to_clean <0>
[ 78.096202] buffer_info[next_to_clean]
[ 78.096202] time_stamp <ffff9c1a>
[ 78.096202] next_to_watch <0000000097d42934>
[ 78.096202] jiffies <ffff9e6a>
[ 78.096202] desc.status <168000>
[ 79.587406] {11}[Hardware Error]: Hardware error from APEI Generic
Hardware Error Source: 0
[ 79.595744] {11}[Hardware Error]: It has been corrected by h/w and
requires no further action
[ 79.604254] {11}[Hardware Error]: event severity: corrected
[ 79.609813] {11}[Hardware Error]: Error 0, type: corrected
[ 79.615371] {11}[Hardware Error]: section_type: PCIe error
[ 79.621016] {11}[Hardware Error]: port_type: 4, root port
[ 79.626574] {11}[Hardware Error]: version: 3.0
[ 79.631177] {11}[Hardware Error]: command: 0x0106, status: 0x4010
[ 79.637430] {11}[Hardware Error]: device_id: 0000:00:09.0
[ 79.642988] {11}[Hardware Error]: slot: 0
[ 79.647157] {11}[Hardware Error]: secondary_bus: 0x09
[ 79.652368] {11}[Hardware Error]: vendor_id: 0x177d, device_id: 0xaf84
[ 79.659055] {11}[Hardware Error]: class_code: 000406
[ 79.664180] {11}[Hardware Error]: bridge: secondary_status:
0x6000, control: 0x0002
[ 79.987052] igb 0000:09:00.1: Detected Tx Unit Hang
[ 79.987052] Tx Queue <2>
[ 79.987052] TDH <0>
[ 79.987052] TDT <1>
[ 79.987052] next_to_use <1>
[ 79.987052] next_to_clean <0>
[ 79.987052] buffer_info[next_to_clean]
[ 79.987052] time_stamp <ffff9c1a>
[ 79.987052] next_to_watch <0000000097d42934>
[ 79.987052] jiffies <ffff9f28>
[ 79.987052] desc.status <168000>
[ 79.987056] igb 0000:09:00.1: Detected Tx Unit Hang
[ 79.987056] Tx Queue <3>
[ 79.987056] TDH <0>
[ 79.987056] TDT <1>
[ 79.987056] next_to_use <1>
[ 79.987056] next_to_clean <0>
[ 79.987056] buffer_info[next_to_clean]
[ 79.987056] time_stamp <ffff9e43>
[ 79.987056] next_to_watch <000000008da33deb>
[ 79.987056] jiffies <ffff9f28>
[ 79.987056] desc.status <514000>
[ 81.986688] igb 0000:09:00.1 enp9s0f1: Reset adapter
[ 81.986842] igb 0000:09:00.1: Detected Tx Unit Hang
[ 81.986842] Tx Queue <2>
[ 81.986842] TDH <0>
[ 81.986842] TDT <1>
[ 81.986842] next_to_use <1>
[ 81.986842] next_to_clean <0>
[ 81.986842] buffer_info[next_to_clean]
[ 81.986842] time_stamp <ffff9c1a>
[ 81.986842] next_to_watch <0000000097d42934>
[ 81.986842] jiffies <ffff9ff0>
[ 81.986842] desc.status <168000>
[ 81.986844] igb 0000:09:00.1: Detected Tx Unit Hang
[ 81.986844] Tx Queue <3>
[ 81.986844] TDH <0>
[ 81.986844] TDT <1>
[ 81.986844] next_to_use <1>
[ 81.986844] next_to_clean <0>
[ 81.986844] buffer_info[next_to_clean]
[ 81.986844] time_stamp <ffff9e43>
[ 81.986844] next_to_watch <000000008da33deb>
[ 81.986844] jiffies <ffff9ff0>
[ 81.986844] desc.status <514000>
[ 85.346515] {12}[Hardware Error]: Hardware error from APEI Generic
Hardware Error Source: 0
[ 85.354854] {12}[Hardware Error]: It has been corrected by h/w and
requires no further action
[ 85.363365] {12}[Hardware Error]: event severity: corrected
[ 85.368924] {12}[Hardware Error]: Error 0, type: corrected
[ 85.374483] {12}[Hardware Error]: section_type: PCIe error
[ 85.380129] {12}[Hardware Error]: port_type: 0, PCIe end point
[ 85.386121] {12}[Hardware Error]: version: 3.0
[ 85.390725] {12}[Hardware Error]: command: 0x0507, status: 0x0010
[ 85.396980] {12}[Hardware Error]: device_id: 0000:09:00.0
[ 85.402540] {12}[Hardware Error]: slot: 0
[ 85.406710] {12}[Hardware Error]: secondary_bus: 0x00
[ 85.411921] {12}[Hardware Error]: vendor_id: 0x8086, device_id: 0x10c9
[ 85.418609] {12}[Hardware Error]: class_code: 000002
[ 85.423733] {12}[Hardware Error]: serial number: 0xff1b4580, 0x90e2baff
[ 85.826695] igb 0000:09:00.1 enp9s0f1: igb: enp9s0f1 NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX
> > So, If we are in a kdump kernel try to copy SMMU Stream table from
> > primary/old kernel to preserve the mappings until the device driver
> > takes over.
> >
> > Signed-off-by: Prabhakar Kushwaha <[email protected]>
> > ---
> > Changes for v2: Used memremap in-place of ioremap
> >
> > V2 patch has been sanity tested.
> >
> > V1 patch has been tested with
> > A) PCIe-Intel 82576 Gigabit Network card in following
> > configurations with "no AER error". Each iteration has
> > been tested on both Suse kdump rfs And default Centos distro rfs.
> >
> > 1) with 2 level stream table
> > ----------------------------------------------------
> > SMMU | Normal Ping | Flood Ping
> > -----------------------------------------------------
> > Default Operation | 100 times | 10 times
> > -----------------------------------------------------
> > IOMMU bypass | 41 times | 10 times
> > -----------------------------------------------------
> >
> > 2) with Linear stream table.
> > -----------------------------------------------------
> > SMMU | Normal Ping | Flood Ping
> > ------------------------------------------------------
> > Default Operation | 100 times | 10 times
> > ------------------------------------------------------
> > IOMMU bypass | 55 times | 10 times
> > -------------------------------------------------------
> >
> > B) This patch is also tested with Micron Technology Inc 9200 PRO NVMe
> > SSD card with 2 level stream table using "fio" in mixed read/write and
> > only read configurations. It is tested for both Default Operation and
> > IOMMU bypass mode for minimum 10 iterations across Centos kdump rfs and
> > default Centos ditstro rfs.
> >
> > This patch is not full proof solution. Issue can still come
> > from the point device is discovered and driver probe called.
> > This patch has reduced window of scenario from "SMMU Stream table
> > creation - device-driver" to "device discovery - device-driver".
> > Usually, device discovery to device-driver is very small time. So
> > the probability is very low.
> >
> > Note: device-discovery will overwrite existing stream table entries
> > with both SMMU stage as by-pass.
> >
> >
> > drivers/iommu/arm-smmu-v3.c | 36 +++++++++++++++++++++++++++++++++++-
> > 1 file changed, 35 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/iommu/arm-smmu-v3.c b/drivers/iommu/arm-smmu-v3.c
> > index 82508730feb7..d492d92c2dd7 100644
> > --- a/drivers/iommu/arm-smmu-v3.c
> > +++ b/drivers/iommu/arm-smmu-v3.c
> > @@ -1847,7 +1847,13 @@ static void arm_smmu_write_strtab_ent(struct
> > arm_smmu_master *master, u32 sid,
> > break;
> > case STRTAB_STE_0_CFG_S1_TRANS:
> > case STRTAB_STE_0_CFG_S2_TRANS:
> > - ste_live = true;
> > + /*
> > + * As kdump kernel copy STE table from previous
> > + * kernel. It still may have valid stream table
> > entries.
> > + * Forcing entry as false to allow overwrite.
> > + */
> > + if (!is_kdump_kernel())
> > + ste_live = true;
> > break;
> > case STRTAB_STE_0_CFG_ABORT:
> > BUG_ON(!disable_bypass);
> > @@ -3264,6 +3270,9 @@ static int arm_smmu_init_l1_strtab(struct
> > arm_smmu_device *smmu)
> > return -ENOMEM;
> > }
> >
> > + if (is_kdump_kernel())
> > + return 0;
> > +
> > for (i = 0; i < cfg->num_l1_ents; ++i) {
> > arm_smmu_write_strtab_l1_desc(strtab, &cfg->l1_desc[i]);
> > strtab += STRTAB_L1_DESC_DWORDS << 3;
> > @@ -3272,6 +3281,23 @@ static int arm_smmu_init_l1_strtab(struct
> > arm_smmu_device *smmu)
> > return 0;
> > }
> >
> > +static void arm_smmu_copy_table(struct arm_smmu_device *smmu,
> > + struct arm_smmu_strtab_cfg *cfg, u32 size)
> > +{
> > + struct arm_smmu_strtab_cfg rdcfg;
> > +
> > + rdcfg.strtab_dma = readq_relaxed(smmu->base + ARM_SMMU_STRTAB_BASE);
> > + rdcfg.strtab_base_cfg = readq_relaxed(smmu->base
> > + + ARM_SMMU_STRTAB_BASE_CFG);
> > +
> > + rdcfg.strtab_dma &= STRTAB_BASE_ADDR_MASK;
> > + rdcfg.strtab = memremap(rdcfg.strtab_dma, size, MEMREMAP_WB);
> > +
> > + memcpy_fromio(cfg->strtab, rdcfg.strtab, size);
> > +
> > + cfg->strtab_base_cfg = rdcfg.strtab_base_cfg;
> > +}
> > +
> > static int arm_smmu_init_strtab_2lvl(struct arm_smmu_device *smmu)
> > {
> > void *strtab;
> > @@ -3307,6 +3333,9 @@ static int arm_smmu_init_strtab_2lvl(struct
> > arm_smmu_device *smmu)
> > reg |= FIELD_PREP(STRTAB_BASE_CFG_SPLIT, STRTAB_SPLIT);
> > cfg->strtab_base_cfg = reg;
> >
> > + if (is_kdump_kernel())
> > + arm_smmu_copy_table(smmu, cfg, l1size);
> > +
> > return arm_smmu_init_l1_strtab(smmu);
> > }
> >
> > @@ -3334,6 +3363,11 @@ static int arm_smmu_init_strtab_linear(struct
> > arm_smmu_device *smmu)
> > reg |= FIELD_PREP(STRTAB_BASE_CFG_LOG2SIZE, smmu->sid_bits);
> > cfg->strtab_base_cfg = reg;
> >
> > + if (is_kdump_kernel()) {
> > + arm_smmu_copy_table(smmu, cfg, size);
> > + return 0;
> > + }
> > +
> > arm_smmu_init_bypass_stes(strtab, cfg->num_l1_ents);
> > return 0;
> > }
> > --
> > 2.18.2
> >
_______________________________________________
kexec mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/kexec
